DELL 2130cn User Manual

4. If ordering by phone, call the number that appears under the  Order by Phone  heading.   
 
Storing Print Media   
To avoid potential paper feeding problems and uneven print quality, there are several things you can do.  
l   To achieve the best possible print quality, store print media in an environment where the temperature is approximately 21°C (70°FyfDQGWKHUHODWLYH 
humidity is 40%.  
 
l   Store cartons of print media on a pallet or shelf, rather than directly on the floor.  
 
l   If you...

   
   
3. Pull the cartridge holder outwards until it stops, and then pull the toner cartridge out of the holder.   
 
   
   
   
Installing a New Toner Cartridge  
   
1. Ensure that the color of the new toner cartridge matches that on the handle before replacing it. Shake the toner cartridge five or six times to distribute 
the toner evenly.   
 
   
   
2. Insert the toner cartridge into the associated cartridge holder, and slide the latches of the toner cartridge until it locks well....

   
   
3. Close the side cover.   
 
   
Replacing the Print Head Device (PHD) Unit   
   
   
1. Ensure that the printer is turned off.   
 
     
2. Pull the standard 250 - sheet tray out of the printer carefully. Hold the tray with both hands, and remove it from the printer.   
 
   
   
3. Press the side button and open the front cover.   
 
   
   
4. Open the belt unit.   
   CAUTION:  Before performing any of the following procedures, read and follow the safety instructions in your  Product...

   
   
5. Turn the four PHD lock levers counter - clockwise.   
 
   
   
6. Pull the PHD unit out of the printer.   
 
   
   
Installing the PHD Unit  
   
1. Open the PHD packaging.   
 
   
   
2. Remove the PHD unit from the packaging.   
   

   
   
3. Completely remove the eight yellow ribbons from the PHD unit.   
 
   
   
4. Remove the rear protective cover from the PHD unit.   
 
   
   
5. Insert the PHD unit until the line on the handle aligns with the white line on the printer.   
 
   
   
6. Turn the four PHD lock levers 90 degrees clockwise to lock the PHD unit.   
 
   
      NOTE:  Do not remove the front protective cover at this moment.  

7. Carefully remove the front protective cover from the PHD unit.   
 
   
   
8. Close the belt unit by pushing it up.   
 
   
   
9. Close the front cover.   
 
   
   
10. Insert the standard 250 - sheet tray into the printer, and push until it stops.   
 
   
   
Replacing Retard Roller   
Keeping the retard roller in the paper tray clean helps ensure the best possible copies. It is recommended to clean the separator at regular intervals.  
   
   
Dell retard rollers are available only through...

Removing the Used Retard Roller in the Standard 250 - Sheet Tray  
   
1. Pull the standard 250 - sheet tray out of the printer carefully. Hold the tray with both hands, and remove it from the printer.   
 
   
   
2. By holding the retard roller tabs with your fingers, pull the retard roller out of the groove in the axle.   
 
   
   
   
Installing the New Retard Roller in the Standard 250 - Sheet Tray  
   
1. Align the new retard roller to the groove on the axle.   
 
   
   
2. Insert the retard...

   
   
3. Load paper and place it in the printer.   
 
   
   
Cleaning the Feed Roller Inside the Printer   
Clean the feed roller inside the printer if print media does not feed correctly.  
   
1. Ensure that the printer is turned off.   
 
     
2. Pull the standard 250 - sheet tray out of the printer carefully. Hold the tray with both hands, and remove it from the printer.   
 
   
   
3. Push the side button and open the front cover.   
 
   
   
4. Open the belt unit.   
   CAUTION:  Do not use...

   
   
5. Turn the four PHD lock levers counter - clockwise, and then pull the PHD unit out of the printer.   
 
   
   
   
6. Clean the feed roller inside the printer with a dry cloth.   
 
   
   
7. Insert the PHD unit until it stops and turn the four PHD lock levers clockwise to lock the PHD unit.   
    NOTE:  Keep the PHD unit in the dark place. Avoid exposing the PHD unit to light.  

   
   
8. Close the belt unit by pushing it up.   
 
   
   
9. Close the front cover.   
 
   
   
10. Insert the standard 250 - sheet tray into the printer, and push until it stops.   
 
   
   
Cleaning the CTD Sensor Inside the Printer   
Clean the CTD sensor only when an alert for the CTD sensor is shown on the Status Monitor or operator panel.  
   
1. Ensure that the printer is turned off.   
 
     
2. Pull the standard 250 - sheet tray out of the printer carefully. Hold the tray with both...