Dell 1350cnw User Guide

Loading Print Media167
4Pull the MPF extension forward until it stops.
5Adjust the paper width guides to their maximum width.
6Before loading the print media, flex the sheets back and forth, and then 
fan them. Straighten the edges of  the stack on a level surface.
 

168Loading Print Media
7Load print media on the MPF with the top edge first and with the 
recommended print side facing up.
8Adjust the width guides until they re st lightly against the edges of the 
stack of print media.
9Slide the length guide towards the prin ter until it touches the print media.
 

Loading Print Media169
 NOTE: Depending on the size of print media, first slide the length guide 
backward until it stops, and then slide t he MPF extension until it touches print 
media.
10Insert the PSI into the printer and th en align the PSI to the marking on 
the paper tray.
 

170Loading Print Media
Loading Envelopes in the Multipurpose Feeder (MPF)
 NOTE: When you print on envelopes, be sure to  specify the envelope setting on the 
printer driver. If not specified, the  print image will be rotated 180 degrees.
When Loading Envelope#10, DL, or Monarch
Load envelopes with the side to be prin ted on facing up, the flap side facing 
down, and the flap turned to the right.
To prevent DL and Monarch from being wrinkled, they are recommended to 
be loaded with the prin t-side facing...

Loading Print Media171
When Loading C5
Load envelopes with the side to be printed on facing up, with the flap open.
 NOTICE: Never use envelopes with windows, or coated linings. These lead to 
paper jams and can cause damage to the printer.
 
NOTE: If you do not load envelopes in the MPF right after they have been removed 
from the packaging, they may bulge. To av oid jams, flatten them as shown below 
when loading them in the MPF.
 

172Loading Print Media
 NOTE: If envelopes are still not fed correctly, add some bending to the flap of the 
envelopes as shown in the following illustration.
The amount of the bending shall be  5mm (0.20 inches) or less.
 
NOTE: To confirm the correct orientation of each print media such as envelopes, 
see the instruction on the Envelope/Paper  Setup Navigator on the printer driver.
 

Loading Print Media173
Loading Letterhead
The letterhead must be toward the top edge of MPF with the print side facing 
up. However, the letterhead must be inse rted top edge first with the print side 
facing down when loading paper into the MPF.
Loading Print Media in the Priority Sheet Inserter 
(PSI)
 NOTE: To avoid paper jams, do not remove the PSI while printing is in progress.
 
NOTE: Use only laser print media. Do not use ink jet paper in this printer.
1Open the front cover.
2Slide the PSI...

174Loading Print Media
3Adjust the paper width guides to their maximum width.
4Before loading the print media, flex  the sheets back and forth, and then 
fan them. Straighten the edges of the stack on a level surface.
5Load print media on the PSI with  the top edge first and with the 
recommended print side facing up.
 

Loading Print Media175
6Adjust the width guides until they rest lightly against the edges of the 
stack of print media.
7Select the paper type from the printer driver if the loaded print media is 
not standard plain paper. If a user-specified print media is loaded in the 
PSI, you must specify the paper size  setting by using the printer driver.
Loading an Envelope in the Priority Sheet Inserter (PSI)
 NOTE: Be sure to fully insert the envelope un til it stops. Otherwise, print media that 
is loaded on...

176Loading Print Media
To prevent DL and Monarch from being wrinkled, they are recommended to 
be loaded with the print-side facing up, flap opened, and facing you.
When Loading C5
Load envelopes with the side to be prin ted on facing up, with the flap open.