DELL 1320c User Manual

This method is usually the best use of system resources. The server handles driver modifications and print job processing. This lets network clients return to 
their programs much faster.  
   
If you use the point and print method, a subset of driver information is copied from the server to the client computer. This is just enough information to send a 
print job to the printer.  
For Windows   XP, Windows XP 64 - bit Edition, Windows Server   2003, and Windows 2000:  
1. On the Windows desktop of the...

 
b.   Select the printer you just created.  
 
c.   Click  File ®   Properties .  
 
d.   From the  General  tab, click  Print Test Page .  
When a test page prints successfully, printer installation is complete.  
 
For Window Vista   and Windows Server 2008:  
1. Click  Start ®   Control Panel ®   Hardware and Sound ®   Printers  ( Start ®   Control Panel ®   Printers  for Windows Server 2008).  
 
2. Click  Add a Printer  to launch the  Add Printer  wizard.  
 
3. Select  Add a network ,  wireless...

back to contents page  
Clearing Jams   
   
Careful selection of appropriate print media and proper loading allow you to avoid most jams. See  Print Media Guidelines  for more information.  
   Avoiding Jams  
   Identifying the Location of Paper Jams  
   Clearing Paper Jams From the Single Sheet Feeder  
   Clearing Paper Jams From the Tray 1  
   Clearing Paper Jams From the Fuser  
Avoiding Jams  
   
l Use only recommended print media. See  Print Media Guidelines  for more information.  
 
     
l...

   
 
Clearing Paper Jams From the Single Sheet Feeder  
1. Pull the jammed paper out of the single sheet feeder. If no jammed paper can be found or it is hard to remove the paper, go to the next step to remove 
the jammed paper from the inside of the printer.  
 
 
   
2. Remove the tray 1 from the printer, and then pull out the jammed paper remaining inside the printer. If no jammed paper can be found or it is hard to 
remove the paper, go to the next step to remove the jammed paper from the inside of...

   
4. Close the front cover.  
 
5. Insert the tray back into the printer, and push until it stops.  
 
 
   
Clearing Paper Jams From the Tray 1  
1. Pull the tray out of the printer carefully. Hold the tray with both hands, lift the front slightly, and remove it from the printer.  
 
 
   
2. Remove all the jammed and/or creased paper from the tray.  
 
 
   
3. Pull the jammed paper out carefully to avoid tearing it. If it is still hard to remove the paper, go to the next step to remove the jammed...

   
4. Open the front cover by pushing the button (right side) and remove the jammed paper. Then, confirm that there are no scraps of paper remaining inside 
the printer.  
 
 
   
5. Close the front cover.  
 
 
   
6. Insert the tray into the printer, and push until it stops.  
 
 
   
Clearing Paper Jams From the Fuser  
1. Turn off the printer and wait for 30 minutes.  
 
2. Push the button (right side) and open the front cover.  
 
 
   
3. Lift the levers at both ends of the fuser, and remove the...

   
4. Open the cover of the fuser and remove the jammed paper.  
 
5. Close the cover of the fuser and press down the levers at both ends of the fuser.  
 
 
   
6. Confirm that there are no scraps of paper remaining inside the printer, and then close the front cover.  
 
 
   
   
back to contents page  CAUTION:  The fuser is hot. Do not touch it, doing so may cause burns.  

back to contents page  
Troubleshooting Guide   
   
   Basic Printer Problems  
   Printing Problems  
   Print Quality Problems  
   Other Problems  
   Contacting Service  
Basic Printer Problems  
   
Some printer problems can be easy to resolve. If a problem occurs with your printer, check each of the following:  
   
l The printer power cable is plugged into the printer and a properly grounded electrical outlet.  
 
     
l The printer power is on.  
 
     
l The electrical outlet is not turned...

Print Quality Problems  
Print is too light.  
 
   
 
All of the print is too light.  
  Ensure the Tray 1 is securely inserted.  
Do not overfill the print media sources.  
Do not force print media into the single 
sheet feeder when you load it; 
otherwise, it may skew or buckle.  
Remove any curled print media from 
sources.  
Load the recommended print side 
correctly for the type of print media you 
are using. See  Loading Print Media in 
Tray 1  for more information.  
Turn the print media over or...

Part of the print is too light.  
  the printer driver.    
Ensure Non - Dell Toner is not selected in the Printer 
Maintenance tab in the Tool Box.  
1.   Click the  Tool Box  button.    
Set Toner Saving Mode to Off in the printer driver.  
1.   Press [Printing Preferences], and then click the 
Advanced tab.    
If you are printing on an uneven print surface, change the 
paper type setting in the printer driver. For example, 
change the plain paper to thick.  
1.   Press [Printing Preferences], and...