Daewoo Frs 2021 Service Manual

3) Refrigerator Bottom Light
4) Wine Holder
5) Shelves
* Snap out the bottom hook of light cover with a flat tip screw driver.
* Hold down the light cover to pull out.
* Change the light bulb.
   (Assembling is the reverse order of disassembling.)
* Remove two screw caps on the top of Wine holder with a (-) driver.
* Unscrew 2 screws with a (+) dirver.
* Hold end of wineholder and pull up smoothly after seperating completel\
y fixed hook.
   (Assembling is the reverse order of disassembling.)
* Pull...

6) Return Duct Cover
7) Dairy Pocket
8) Refreshment Pocket (Only for FRS-2041)
9) Refrigerator interior parts
* Pull out the cover to arrow direction.
* Pull forward and lift up a little.
* Hold both end and pull up to remove the pocket.
* Lift up a little and then pull forward out.
* Remove foods and shelves of R-compartment.
* Remove screws caps with a tiny tip screw driver and
   remove light cover screws with a (+) screw driver
   (Refer to 2) Top R-Light )
* Disassemble RAMP R A HOUSING, SENSOR...

* Unscrew two screws on the left and right side of
   DAMP COVER.
* Hold the bottom and right of damper to pull down
   to remove.
* After removing bottom R-light cover, unscrew with a (+)
  driver. (Refer to 3) Refrigerator Bottom Light )
* Hold top of the MULT DUCT COVER AS and pull forward
   to remove.
* Remove FAN HOUSING on the right side.
  (Unscrew two screws on the FIXTURE MOTOR B.)
* Assembling is the reverse order of disassembling.
  When assembling, be careful not to disturb Fan.
- 53 -
 

6-1. Installation Preparation
Dimensions (Including Door Handles)
   Sufficient space from refrigerator back to thewall for free air ventilation    Avoid direct sunlight.
   Once the installation place is ready follow the installation instruction\
s.
If surround temperature of refrigerator is low (below 5C), foods can b\
e frozen or the refrigerator can work
in an abnormal way.
  
Check if the refrigerator can pass 
a doorway or enter a door first.
Find a suitable place to install.
6. INSTALLATION GUIDE...

   Remove front bottom cover first, if it is attached.
!
!
@
!
@
1Unscrew top hinge cover with a screw driver.
Insert a thin screw driver into the side
groove of the cover to remove.
2
Turn top hinge fastener counterclockwise
3~4 times.
 
Disconnect the harness wires.
3Lift up the front of hinge to remove. (After
the hinge is removed the door can fall
4
Lift the door straight up to remove.
Removing Freezer Door 
6-2. If the refrigerator can not enter the door, follow these steps.
- 55 -
!
down forward....

!@
!
@
1
Unscrew top hinge cover with a screw
driver.Insert a thin screw driver into the side
groove of the cover to remove.
2
Turn top hinge fastener counterclockwise
3~4 times. 
Disconnect harness wires.
3
Lift up the front of hinge to remove. (After
the hinge is removed the door can fall
down forward. Be careful !)
4
Lift the door straight up to remove.
Removing Refrigerator Door 
- 56 -
!
 

!
@
!
@
! @
Replacing Freezer Door
- 57 -
!
1
Insert the bottom hole of freezer door
straight to the bottom hinge pin.
2
Let the top of door close to the cabinet and
insert the top hinge pin to the top hole of
freezer door.
( Insert the back of hinge to the groove of
protrusion first, then front to the top hole of
door.)
3
Turn the hinge fastener tightly to the end.
Connect harness wirings and screw ground
wire. 
4
Click and screw the top hinge cover.
 

Replacing Refrigerator Door
- 58 -
!
@
!
@
!
@
!
1
Insert the bottom hole of refrigerator door
straight to the bottom hinge pin.
2
Let the top of door close to the cabinet and
insert the top hinge pin to the top hole of
freezer door. ( Insert the back of hinge to the groove of
protrusion first, then front to the top hole of
door.)
3
Turn the hinge fastener tightly to the end.
Connect harness wirings and screw ground
wire.Click and screw the top hinge cover.
 

 
1
Insert a screw driver (flat tip) into a groove of the right wheel (bo\
ttom of refrigerator) and
turn it clockwise until the door is balanced. (clockwise to raise refri\
gerator door ;
counterclockwise to lower)
  
Unless the refrigerator door is balanced by step 1, then follow the next\
 steps.
2  
Loosen 3 hinge bolts(2 on the left + 1 on the right) a little. (Do no\
t unfasten them completely)
Insert a hexagonal wrench into the groove of adjusting nut and turn cloc\
kwise until the
door is level....

15
16
1314
10
9
12
11
2722
24
21
25
2326
18
17
20
19
4
3
2
6
8
71
7. EXPLODED VIEW AND PARTS LIST
7-1. Total Exploded ViewFRS-2021  /  FRS-2421
- 60 -
CABINET
303632
31
47
3435
38
37
39
33
29
46
45
40
44
4241
49
43
48MECH ROOM