Daewoo Dt 42a1 Users Manual

							52
Watching Two Pictures SimultaneouslyWatching Two Pictures Simultaneously
Select the program
•  Using program Up/Down buttons
(PR
/PR), you may select the desired 
channels for sub-pictures.
•  The PR Up/Down buttons select the
TV channels.4
Select the Input Source
•  Various signal sources can be displayed 
within the sub-picture under PIP mode.
•  Once the PIP mode is on, you may change 
the input source of the sub-picture by press-
ing the ‘SOURCE’ button.
•  Pressing the ‚SOURCE’ button repeatedly will
cycle through following order.
5
T V à AV1 à AV2 à AV 3
Available PIP Input Combinations
•  Main-pictue and sub-pictue input 
combinations
6MAINPIPTV
(MAIN)AV1
(CVBS)AV2
(CVBS)AV3S-VIDEOAV1
(RGB)AV2
(RGB)
TV
(MAIN)OOOOOOO
AV1
(CVBS)O X OOO X O
AV2
(CVBS)OO X OOO X
AV3
OOO X X OO
S-VIDEOOOO X X OO
AV1
(RGB)XXXXXXX
AV2
(RGB)XXXXXXX
 
						

							53
Adjusting Auto Sound ModeAdjusting Auto Sound Mode
•  Enjoy various sound 
modes by selecting
your favourite Sound
Mode depending on
the kinds of moving
pictures.
Adjusting Auto
Sound Mode
Select “SOUND  MODE”.
•  Press the “SOUND MODE” on the remote 
control.
•  While pressing the “SOUND MODE” for the 
first time, the current sound mode will be 
displayed.
1
KEvery Press of the Button Changes Modes.
•  Each time you press the button, a different 
sound mode appears. 
The sequence used is as follows:
2
Normal /³ Movie /³ Music /³ News /³ User
* Normal :   Suitable for watching any motion picture
* Movie :   Select this mode to simulate being at a movie theatre
* Music :  Ideal for listening to music
* News :   Allows human voice to be heard more clearly
* User :   Allows the user to adjust as desired.
MENU will Disappear.
•  After selecting a desired Sound Mode, the
on-screen menu will disappear in about
2~3 seconds.
•  Normal, Movie, Music and News modes
are factory preset values.
If you want to customise the sound modes
for your preference, refer to the following 
page.
3
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
54
Press the MENU Button.
• The MENU screen as below will be displayed.
1
  Customising Sound Mode    Customising Sound Mode
•  This feature allows the 
user to adjust for their 
preference.
Customising
Sound Mode
Press the “ PR ” Button.
•  Select [Sound] by the “PR”  
buttons, then press the “VOL
” button 
to display the following.2
Picture
Sound
Screen
Feature
InstallBalance  0
Effect Off 
AVC Off 
Mode Normal 
120Hz  0
500HZ  0
1. 5k Hz  0
5kHz  0
10kHz  0
Move SelectExit
Select SOUND BALANCE.
•  Select “Sound-Balance” by the “VOL” 
buttons, then adjust it.
3
Picture
Sound
Screen
Feature
InstallBalance  0
Effect Off 
AVC Off 
Mode Normal 
120Hz  0
500HZ  0
1. 5k Hz  0
5kHz  0
10kHz  0
Move AdjustExit
Picture
Sound
Screen
Feature
InstallMode Normal 
Brightness 32
Contrast 48
Sharpness 32
Color 32
Colour Temp.  Normal
N.R. On
CTI On
Move Select Exit
 
						

							55
•  If a programme is received 
in two languages (dual 
language), you can switch 
to Dual I, Dual II or F mono 
by pressing the I/II button 
of the remote control 
repeatedly.
Dual I
Dual I sends the primary 
broadcast language to the
loudspeakers.
Dual II
Dual II sends the 
secondary broadcast 
language to the
loudspeakers.
F Mono
F Mono sends the Mono 
sound to the loudspeakers.
Picture
Sound
Screen
Feature
InstallBalance  0
Effect Off 
AVC Off 
Mode Normal 
120Hz  0
500HZ  0
1. 5k Hz  0
5kHz  0
10kHz  0
Move AdjustExit
Language selection
for dual language
broadcast
Select the Effect Mode.
•  Select [Effect] by pressing the “PR” then 
select the desire sound effect by pressing the 
“VOL
” button.
• [Effect]: Used to emphasize stereo effect.4
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
56
Customising Sound ModeCustomising Sound Mode
Select the Sound Mode.
•  Select the Sound Mode by pressing the
“
PR” buttons, then adjust it by pressing 
the “
VOL” buttons.5
Picture
Sound
Screen
Feature
InstallBalance  0
Effect Off 
AVC Off 
Mode Normal 
120Hz  0
500HZ  0
1. 5k Hz  0
5kHz  0
10kHz  0
Move AdjustExit
NOTES:
1)  User Mode : Used as an equalizer with which the user can
adjust the sound frequency as desired.
2)  If you modify the sound frequency in auto Sound Mode
(News, Movie, Music, etc.), it is automatically switched to the
User Mode.
3)  For a realistic sound effect, lower than 120Hz frequency
sound and greater than 12kHz frequency adjust the
equalizer accordingly.
4) AVC function :  This function adjusts volume to the set level
automatically. However, dependent on the
sources, it may have different volume levels
because the sound sources have their own
initially set up levels.
Normal /³ Movie /³ Music /³ News /³ User
* Normal :   Suitable for watching any motion picture
* Movie :   Select this mode to simulate being at a movie theatre
* Music :   Suitable for listening to music
* News :   Allows human voice to be heard more clearly
* User :   Allows the user to adjust as desired.
 
						

							Component 1
VCR/DVD
SATTV
CATV
57
Press the Input Signal Selecting Button.
•    Press  the “TV”, “AV”, “COMPONENT”  or “PC/DVI”  button
on the remote control or the PDP Display to select the
desired input signal.
•  Each time you press input mode buttons, a different input 
mode appears. 
The sequence used is as follows:•  Used to select INPUT 
signal of external device 
connected to the PDP.INPUT SIGNAL
NOTES:
1)  If an external device is not connected or INPUT signal 
is not applied a Warning Message (“No Signal”) will be 
displayed.
2)  In this case, check if external device is connected 
and/or terminal connection is properly fitted.
3)  Also, you can select input using [INPUT SELECT ] 
button in the keypad of the PDP unit. The sequence of 
selection is as follows:
TV -> AV1 -> AV2 -> AV3 ->Component1 
-> Component2 -> PC -> DVI -> TV
• “TV  ”  button
1
Selecting INPUT SIGNALSelecting INPUT SIGNAL
TV
• “AV  ”  buttonAV 1AV 2AV 3
• “COMPONENT”  button
Component1Component2
• “PC/DVI”  button
PCDVI
 
						

							Comopnent 1
PM 12:00
 PR22  PR Name
 Mono/Stereo  Time PR22   PR Name
 Mono PM 12:00
AV 1
 PM 12:00
Component 1
PM 12:00
-  Press the [RECALL] button on the remote control, then displays basic informations of the current input signal,
Under this state, pressing the [RECALL] button once more, additional informations about the current input signal
will be displayed on the OSD.
H:1920
V:1080
[RECALL] button
[RECALL] button 
once more
H:1920
V:1080
Video PAL B/G
Audio I
Country GB
Channel C35
Video PAL B/G
58
Press the RECALL Button.
• Press the [RECALL] button on the Remote Control.
1
 Checking the Current Input Signal  Checking the Current Input Signal
•  Used to check the
INPUT signal mode,
current time,
resolution, channel,
etc.
Checking the
Current Input Signal
1. If you watch Component, PC, or DVI :
Displays which input terminal is used, and indicates the 
input signal mode.
Indicates the horizontal and vertical resolution of the 
current INPUT signal.
Indicates the mode and current time.
2. If you watch TV:
Displays the program number and its name.
Indicates the current sound state and time.
Displays additional informations of TV signal of TV signal, 
video and audio system. country, channel.
3. If you watch VCR image:
Displays the program number and input terminal, which is used.
Indicates the mode and current time.
Displays the video system of input signal
NOTES:
1)  “1920 x 1080” displayed in the INPUT signal is not the
resolution of the monitor, but the signal that is sent by the
Digital Broadcasting Receiver.
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
59
•  Used to select the 
tanslucent level of MENU 
background and language 
used in MENU.
Selecting
Languages
MENU Background, Language and Child Lock SettingMENU Background, Language and Child Lock Setting
Press the MENU Button.
• The MENU screen will be displayed as below.
1
Press the “ PR ” Button.
•  Select [Features] by the “PR” button.
2
Picture
Sound
Screen
Feature
InstallBackground  10
Language English 
Child Lock  Off 
MGDI On 
Auto Power  Off 
Time Setting   
ISM  
Initialize  
Move SelectExit
Select the menu Background.
•  Select the MENU [Background] by pressing 
the “VOL
” button.
•  Adjust the tanslucent level of OSD back-
ground using “VOL
” buttons. 
3
Picture
Sound
Screen
Feature
InstallBackground  10
Language English 
Child Lock  Off 
MGDI On 
Auto Power  Off 
Time Setting   
ISM  
Initialize  
Move AdjustExit
Picture
Sound
Screen
Feature
InstallMode Normal 
Brightness  32
Contrast  48
Sharpness  32
Color  32
Colour Temp.  Normal
N.R. On
CTI On
Move SelectExit
 
						

							60
Select LANGUAGE by using the “PR”Button.
• Select [Language] by using the”PR” button.
•  Every press of the “VOL
” button while you are 
in the [Language] mode would cycle through 
the different languages.4
MENU Background, Language and Child Lock SettingMENU Background, Language and Child Lock Setting
NOTES:
•   When power is turned on the first time, ‘SELECT
LANGUAGE’ mode will be displayed, then, select the
desired language by using “VOL
” button. 
(Displayed only once)
Picture
Sound
Screen
Feature
InstallBackground  10
Language English 
Child Lock  Off 
MGDI On 
Auto Power  Off 
Time Setting   
ISM  
Initialize  
Move AdjustExit
Child Lock Setting
• Select [Child Lock] by the “PR” buttons.
•  Whenever “VOL
” button is pressed, the lock
mode would cycle On and Off.
•   While the Child Lock is ON, if you have not
turned off the PDP, all of it’s keys will work
normaly. However, after turning the PDP off,
the PDP will not be turned on with the keypad
on the PDP. Only by the remote controller, the
PDP is turned on.5
Picture
Sound
Screen
Feature
InstallBackground  10
Language English 
Child Lock  Off 
MGDI Off 
Auto Power  Off 
Time Setting   
ISM  
Initialize  
Move AdjustExit
 
						

							61
•  MGDI function can not be 
used In PC and DVI modes.
MGDI
MGDI (Meta Genuine Digital Image)MGDI (Meta Genuine Digital Image)
MGDI is the image enhancement technology of Daewoo Electronics, which provides more clear, realistic, and delicate 
images.
Press the MENU Button.
• The MENU screen will be displayed as below.
1
Select Features
• Select [Features] by the “ PR ” button.
2
MGDI Setting
•  Enter the sub Menu by using the “VOL” 
button.
•  Select the [MGDI] by pressing the “
PR” 
button.
•  You can select [MGDI] On or Off mode by 
using the “VOL
” button.
3
Picture
Sound
Screen
Feature
InstallBackground  10
Language English 
Child Lock  Off 
MGDI Off 
Auto Power  Off 
Time Setting   
ISM  
Initialize  
Move SelectExit
Picture
Sound
Screen
Feature
InstallMode Normal 
Brightness  32
Contrast  48
Sharpness  32
Color  32
Colour Temp.  Normal
N.R. On
CTI On
Picture
Sound
Screen
Feature
InstallBackground  10
Language English 
Child Lock  Off 
MGDI On 
Auto Power  Off 
Time Setting   
ISM  
Initialize  
Move SelectExit Move SelectExit