Daewoo Dt 42a1 Users Manual

							22
EditEdit
Deleting the Program.
•  Place the selection bar on the program that you want to 
delete using the “
PR” and “VOL” buttons.
•  Press the Delete(Yellow) button.
• The deleted program goes to PR number 99 for recover.1
Edit
PR CH Name  Skip
PR98  S41  _ _ _ _  o
PR99  S41  _ _ _ _  o
PR0  C69  _ _ _ _ 
PR1  S41  _ _ _ _  o
PR2  S41  _ _ _ _  o
PR3  S41  _ _ _ _  o
PR4  S41  _ _ _ _  o
SkipExit
Delete Move Adjust
Moving the Program Positions
•  Place the selection bar on the program
that you want to move.
• Press the Move(Green) button.
•  It becomes ready for moving as the
colour of selection changes to green.
•  Move the program that you desire to
move to the wanted PR number.
•  Press the Move(Green) button again to 
finish. The colour of selection changes 
to yellow.
2
Skipping the Channels
•  Using “PR” a n d   “VOL” buttons, place the
selection bar on the program that you want to skip.
• Press the Skip(red) button.
• The colour of the program changes to red.
• The program will be skipped.
•  In order to cancel skip state,press the Skip(red) button
again.
3
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
23
Manual SetupManual Setup
Press the Number Buttons(0~9) or the “VOL ” 
Button to Select a Program Number You Want.
1
Picture
Sound
Screen
Feature
InstallManual Setup
Program 01
Channel C06
Fine Tune    48
Name  – – – – –
Video PAL
Audio D/K
Search  
Memory  
Move Adjust Exit
Adjust0~9
Find the Desired Channel.
•  Using  “VOL” button or number keys, select 
the desired channel directly, if you know it other-
wise step through the numbers using the “VOL
” 
button until you find the right channel.
•  By pressing red teletext button, you can toggle C 
channel to S-channel.2
Fine Tune
•  If you are unable to get a good picture or 
sound because of a poor signal reception, 
it is possible to adjust it with the Fine Tune 
feature.
•  Move the selection bar to Fine Tune and 
press the “
VOL” buttons to activate Fine 
Tune up or down.
•  Note that it operates while the “
VOL” 
button is being pressed.
•  It will be saved only when you select “OK” in 
Memory.
3
Picture
Sound
Screen
Feature
InstallManual Setup
Program 01
Channel C06
Fine Tune    48
Name  – – – – –
Video PAL
Audio D/K
Search  
Memory  
Move Adjust Exit
Cable/Air
Picture
Sound
Screen
Feature
InstallManual Setup
Program 01
Channel C06
Fine Tune    48
Name  – – – – –
Video PAL
Audio D/K
Search  
Memory  
Move Adjust ExitAdjust
0~9
Cable/Air
Adjust0~9
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
24
Manual SetupManual Setup
4
Picture
Sound
Screen
Feature
InstallManual Setup
Program 01
Channel C06
Fine Tune    48
Name          C06
Video PAL
Audio D/K
Search  
Memory  
Move Adjust Exit
Select the Video and Audio System.
•  You can select the Video (PAL,SECAM, 
SECAM-L) and Audio (B/G, DK, I, L) 
System with these functions.
5
Picture
Dźwiek
Screen
Feature
InstallManual Setup
Program 01
Channel C06
Fine Tune    48
Name          C06
Video PAL
Audio D/K
Search  
Memory
Move Select Exit
Name the program
•  Using ”VOL” button, move the position 
where you want to write the character.
•  Select the desired character with the “PR” 
button.
• There are A-Z, +, ., /, and 0-9 characters.
•  After naming, you can exit by pressing the 
”Menu” button.
Cable/Air
Adjust0~9
Picture
Dźwiek
Screen
Feature
Install
Manual Setup
Program 01
Channel C06
Fine Tune    48
Name          C06
Video PAL
Audio D/K
Search  
Memory
Move Select Exit
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
25
Find the Desired Channel with ‘Search’.
•  By selecting the Search function, you 
can find the desired channel, but it 
searches only one channel unlike Auto 
Setup.
•  If the nearest channel is found, 
the searching would be stopped 
automatically.
6
Picture
Dźwiek
Screen
Feature
InstallManual Setup
Program 01
Channel C06
Fine Tune    48
Name          C06
Video PAL
Audio D/K
Search  
Memory
Move Select Exit
Memorize the Program.
• Without Memorizing, the program will not be saved.
•  Press “
VOL” buttons to memorize the program 
after selecting ‘Memory’. “OK” will flash green.7
Picture
Sound
Screen
Feature
InstallManual Setup
Program 01
Channel C06
Fine Tune    48
Name          C06
Video PAL
Audio D/K
Search  
Memory
Move Select Exit
 
						

							26
Watching Digital BroadcastsWatching Digital Broadcasts
•  To watch digital
broadcasts:
-  Purchase a separate
Digital Broadcasting
Receiver(SET-TOP BOX)
-  Connect the PDP to a
Digital Broadcasting
Receiver as shown right.
Watching Digital
Broadcasts
Connect a Digital Broadcasting Receiver to the PDP
• Prepare A/V cables.
•  Connect the cables from the digital TV Receiver output terminal to the
PDP(Component 1, 2) input terminal.
• When connecting the cables, be sure to match the cable colours.
1
Digital Broadcasting Receiver
(Set-Top Box) Video Audio
Press the Power Buttons
•  Turn the PDP and the receiver ON.
2
 
						

							COMPONENT
Component 1   Component 2
27
Input Select
•  Select [Component 1 or Component 2] by
pressing the “COMPONENT” button of the
remote control or using the “INPUT SELECT”
button of the PDP unit.
•  Each time you press the “COMPONENT” 
button, different input modes appear. 
The sequence is as follows:
3
Select the Desired Channel and Function
•  Select the desired channel and function
by using the remote control of the Digital
Broadcasting Receiver.
4
NOTES:
1) Possible digital broadcasting signals: 1080i, 720p, 576p, 480p.
2)  Antenna connection:
Apartment : Check if communal aerial receives digital broadcasts.
Private Houses: Set the indoor/outdoor UHF antenna to the 
direction of the digital broadcasting transmitting company.
3)  For detailed connection method, refer to the owner’s manual of 
Digital Broadcasting Receiver.
4)  What is a component? : Signals with which luminance and
chrominance are separated, producing a sharp picture.
5)  If the Digital Broadcasting Receiver has PC output terminal or DVI
output terminal, connect to ‘PC INPUT’ or ‘DVI INPUT’ at the rear of
the panel of the PDP.
• N.B.:  You cannot select component inputs if the picture in 
picture mode is on. 
  
						

							AV 2AV 1
L
- O I D U
A - R
O
E D I V - S O
E D
I V
AV 3
• N.B.:   When using the AV3 input, there is no need to use both as S-Video
will always take precedence on this input but you must have the right
and left audio leads connected to produce sound when using S-Video.
28
Watching Cable BroadcastsWatching Cable Broadcasts
•   To watch cable broadcasts, 
subscribe to your local 
cable TV broadcasting, 
and then connect a cable 
Broadcasting Receiver to 
the PDP as shown right.
Watching Cable
Broadcasts
Connect a Cable Broadcasting Receiver to the PDP.
• Prepare the A/V cable.
• Connect the receiver(Output) to PDP(Video Input) as shown below.
•  While using the scart cable for connection, put the ferrite core to the middle 
of the cable to prevent EMI (Electro Magnetic Interference).
1
Cable Broadcasting Receiver Video/Audio
S-Video
Video/Audio
Ferrite Core
Press the Power Buttons
• Turn the PDP and the receiver ON.
2
 
						

							• N.B.:  An S-Video input into AV3 will take precedence 
over the normal yellow video lead so no need to 
utilise this if S-Video lead is used but you must 
still use the right and left audio leads to produce 
sound.
AV1 AV2
AV(S)3
AV
29
NOTES:
1)  If your local cable company re-transmits digital broadcasts,
you may watch normal broadcasts and digital broadcasts
simultaneously. For detailed information, refer to your local
cable company.
2)  A/V OUT OF SCART TERMINAL will provide with TV signal
output of the selected channel.
Input Select
•  Select [AV 1(Scart), AV 2(Scart) or 
AV3(S-Video)] by pressing the [AV ] 
button of the remote control or the
“INPUT SELECT” in keypad of the PDP unit.
•  Each time you press the [AV ] button, 
different input modes appear. 
The sequence is as follows:
3
Select the Desired Program and Function
*   Select the desired program and function
by using the remote control of the Cable
Broadcasting Receiver.
4
  
						

							AV 2AV 1
L
- O I D U A - R
O E D I
V - S
O E D I V
AV 3
• N.B. :  If using AV3 then S-Video takes precedence so no need for video
lead if S-Video lead used the audio leads must still be used to
produce sound.
30
Watching Satellite BroadcastsWatching Satellite Broadcasts
•  To watch satellite 
broadcasting, subscribe 
to Digital Satellite 
Broadcasting, then connect 
the satellite Broadcasting 
Receiver to the PDP as 
shown right.
Watching Satellite
Broadcasts
Connect a Satellite Broadcasting Receiver to the PDP.
• Prepare the A/V cable.
• Connect the receiver(Output) to PDP(Video Input) as shown below.
• When connecting to an external AV source, be sure to match the colours.
•  If using the scart cable for connection, put the ferrite core to the middle of 
the cable for preventing EMI.
1
Satellite Broadcasting Receiver Video/Audio
S-Video
Video/Audio
Ferrite Core
Press the Power Buttons
• Turn the PDP and the Satellite receiver ON.
2
 
						

							AV1 AV2
AV(S)3
AV
31
Input Select
•  Select [AV 1(Scart), AV 2(Scart) or
AV3(S-Video)] by pressing the [AV ]
button of the remote control or the
“INPUT SELECT” in keypad of the PDP unit.
•  Each time you press the [AV ] button, different 
input modes appear. 
The sequence is as follows:
3
Select the Desired Program and Function
•  Select the desired program and function
by using the Remote Control of the
Satellite Broadcasting Receiver.
4