D-Link Router DIR-100 User Manual

31D-Link DIR-100 User Manual
Section 3 - Configuration
Check this box to enable DMZ.
Enter the IP address of the computer you would like 
to open all ports to.
Check  this  box  to  allow  PPTP  VPN  traffic  to  pass 
through the router to your VPN client.
Check  this  box  to  allow  LTP  VPN  traffic  to  pass 
through the router to your VPN client.
Check  this  box  to  allow  IPSec  VPN  traffic  to  pass 
through the router to your VPN client.
Enable DMZ Host:
DMZ IP Address:
Enable PPTP...

3D-Link DIR-100 User Manual
Section 3 - Configuration
To use the Universal Plug and Play (UPnP™) feature 
click on Enabled. UPNP provides compatibility with 
networking equipment, software and peripherals.
Unchecking  the  box  will  not  allow  the  WBR-310 
to respond to pings. Blocking the Ping may provide 
some extra security from hackers. Check the box to 
allow the WAN port to be “pinged”.
You  may  set  the  port  speed  of  the  WAN  port  to 
10Mbps,  100Mbps,  or  auto.  Some  older...

33D-Link DIR-100 User Manual
Section 3 - Configuration
Use the QoS WAN Upstream Bandwidth drop-down 
menu to adjust the upstream bandwidth setting.
This option is disabled by default.Enable this option 
for better performance and experience with online 
games  and  other  interactive  applications,  such  as 
VoIP.
Upstream 
Bandwidth:
QoS:
QoS 

34D-Link DIR-100 User Manual
Section 3 - Configuration
Enter the new password for the Administrator login. 
The administrator can make changes to the settings.
Remote  management  allows  the  DIR-100  to  be 
configured  from  the  Internet  by  a  web  browser.  A 
username and password is still required to access the 
Web-Management interface. In general, only a member 
of  your  network  can  browse  the  built-in  web  pages 
to perform Administrator tasks. This feature enables 
you to perform...

35D-Link DIR-100 User Manual
Section 3 - Configuration
Time Settings
NTP  is  short  for  Network  Time  Protocol.  NTP 
synchronizes  computer  clock  times  in  a  network  of 
computers. This field is optional.
To manually input the time, enter the values in these 
fields  for  the  Year,  Month,  Day,  Hour,  Minute,  and 
Second. Click Set Time.
Select the Time Zone from the drop-down menu.
To  select  Daylight  Saving  time  manually,  select 
enabled or disabled, and enter a start date and an end...

36D-Link DIR-100 User Manual
Section 3 - Configuration
System Settings
Use this option to save the current router configuration 
settings to a file on the hard disk of the computer you 
are using. First, click the Save button. You will then 
see a file dialog, where you can select a location and 
file name for the settings. 
Use  this  option  to  load  previously  saved  router 
configuration settings. First, use the Browse control 
to find a previously save file of configuration settings. 
Then, click...

37D-Link DIR-100 User Manual
Section 3 - Configuration
Firmware Upgrade
Click on the link in this screen to find out if there is an 
updated firmware; if so, download the new firmware 
to your hard drive.
After you have downloaded the new firmware, click 
Browse in this window to locate the firmware update 
on your hard drive.  Click Save Settings to complete 
the firmware upgrade.
Firmware 
Upgrade:
Browse:
You can upgrade the firmware of the Router here. Make sure the firmware you want to use is on...

38D-Link DIR-100 User Manual
Section 3 - Configuration
Dynamic DNS
Enable  this  option  only  if  you  have  purchased  your 
own domain name and registered with a dynamic DNS 
service provider. The following parameters are active 
when the option is enabled.  
Select a dynamic DNS service provider from the pull-
down list.
Enter  your  entire  host  name;  for  example:  myhost.
mydomain.net. 
Enter  the  username  or  key  provided  by  your  service 
provider. If the Dynamic DNS provider supplies...

39D-Link DIR-100 User Manual
Section 3 - Configuration
System Check
VCT  is  an  advanced  feature  that  integrates  a  LAN 
cable  tester  on  every  Ethernet  port  on  the  router. 
Through  the  graphical  user  interface  (GUI),  VCT 
can be used to remotely diagnose and report cable 
faults such as opens, shorts, swaps, and impedance 
mismatch.  This  feature  significantly  reduces 
service calls and returns by allowing users to easily 
troubleshoot their cable connections.
The Ping Test is used...

40D-Link DIR-100 User Manual
Section 3 - Configuration
Schedules
Give the schedule a name that is meaningful to you, 
such as “Weekday Rule”. 
Place a checkmark in the boxes for the desired days, 
or select the All Week radio button to schedule all 
seven days of the week. 
Select this option if you want this schedule in effect 
all day for the selected day(s). 
If  you  don’t  use  the  All  Day  option,  then  enter  the 
time  here.  The  start  time  is  entered  in  two  fields. 
The first box is...