D-Link Router DIR-100 User Manual

11D-Link DIR-100 User Manual
Section  - Installation
Installation
Getting Started
Installation Location
The DIR-100 functions as an Ethernet LAN for your home or office use. The Router can be placed on a shelf or desktop and ideally 
you should be able to see the LED indicators on the front if you need to view them for troubleshooting. No special wiring or cooling 
requirements are needed but when you are ready to place the Router, you must take into account the following guidelines:• 
Place the...

1D-Link DIR-100 User Manual
Section 3 - Configuration
(the IP address of the DIR-100).
Configuration
The  DIR-100  provides  an  embedded  Web-based  management  utility  making  it  operating  system  independent.  You  can  configure 
your DIR-100 through the Netscape Communicator or Internet Explorer browser in MS Windows®, Macintosh, Linux or UNIX based 
platforms. All that is needed is a web browser such as Internet Explorer\
 or Netscape Navigator with Java Script enabled.
Log in
Open your...

13D-Link DIR-100 User Manual
Section 3 - Configuration
Setup Wizard
You may run the setup wizard to quickly setup your router. 
Click Setup Wizard to launch the wizard.
Click Launch Internet Connection Setup Wizard to begin.
Click Next to continue. 

14D-Link DIR-100 User Manual
Section 3 - Configuration
Create a new password and then click Next to continue.
Select  your  time  zone  from  the  drop-down  menu  and  then  click Next  to 
continue.
Select  the  type  of  Internet  connection  you  use  and  then  click Next  to 
continue. 

15D-Link DIR-100 User Manual
Section 3 - Configuration
If you selected Dynamic, you may need to enter the MAC address of the computer that 
was last connected directly to your modem. If you are currently using that computer, 
click Clone Your PC’s MAC Address and then click Next to continue.
The Host Name is optional but may be required by some ISPs. The default host name 
is the device name of the Router and may be changed.
If you selected PPPoE, enter your PPPoE username and password. Click Next to...

16D-Link DIR-100 User Manual
Section 3 - Configuration
If  you  selected  LTP,  enter  your  L TP  username  and  password.  Click Next  to 
continue.
If you selected BigPond, enter your BigPond Auth Server, username and password. 
Click Next to continue.
If you selected Static, enter your network settings supplied by your Internet provider. 
Click Next to continue. 

17D-Link DIR-100 User Manual
Section 3 - Configuration
Click  Connect  to  save  your  settings.  Once  the  router  is  finished  rebooting,  click 
Continue. Please allow 1- minutes to connect. 
Close your browser window and reopen it to test your Internet connection. It may 
take a few tries to initially connect to the Internet. 

18D-Link DIR-100 User Manual
Section 3 - Configuration
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The default MAC Address is set to the WAN’s physical 
interface MAC address on the Broadband Router. It is 
not  recommended  that  you  change  the  default  MAC 
address unless required by your ISP.
The default MAC address is set to the WAN’s physical 
interface MAC address on the Broadband Router. You 
can  use  the Clone...

19D-Link DIR-100 User Manual
Section 3 - Configuration
Choose Dynamic IP Address to obtain IP Address information 
automatically from your ISP. Select this option if your ISP does 
not give you any IP numbers to use. This option is commonly 
used for Cable modem services.
The Host Name is optional but may be required by some ISPs. 
The  default  host  name  is  the  device  name  of  the  Router  and 
may be changed.
The default MAC Address is set to the WAN’s physical interface 
MAC address on the...

0D-Link DIR-100 User Manual
Section 3 - Configuration
Select Dynamic  (most  common)  or Static.  Select 
Static if your ISP assigned you the IP address, subnet 
mask, gateway, and DNS server addresses.
Enter your PPPoE user name.
Enter  your  PPPoE  password  and  then  retype  the 
password in the next box.
Enter the ISP Service Name (optional).
Enter the IP address (Static PPPoE only).
Enter the Primary and Secondary DNS Server Addresses 
(Static PPPoE only).
Enter  a  maximum  idle  time...