D-Link Dir825 B1 Manual

							56D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
Static.IPv6.Address.Connection
This mode is used when your ISP provides you with a set IPv6 addresses that does not chan\be. The IPv6 information is manua\f\fy entered in your 
IPv6  confi\buration  settin\bs. You  must  enter  the  IPv6  address,  Subnet  Prefix  Len\bth,  Defau\ft  Gateway,  Primary  DNS  Server,  and  Secondary  DNS 
Server. Your ISP provides you with a\f\f this information.
Use.Link-Loca\b.
Address:
IPv6.Address:
Subnet.Prefix.
Length:
Defau\bt.Gateway:
Primary.IPv6.DNS.
Address:
Secondary.IPv6.
DNS.Address:
LAN.IPv6.Address:
The  Link-\foca\f  address  is  used  by  nodes  and  routers  when 
communicatin\b  with  nei\bhborin\b  nodes  on  the  same  \fink. 
This  mode  enab\fes  IPv6-capab\fe  devices  to  communicate 
with each other on the \uLAN side.
Enter the WAN IPv6 address for the router here.
Enter the WAN subnet prefix \fen\bth va\fue used here.
Enter the WAN defau\ft \bateway IPv6 address used here.
Enter the WAN primary DNS Server address used here.
Enter the WAN secondary DNS Server address used here.
These  are  the  settin\bs  of  the  LAN  (Loca\f  Area  Network) 
IPv6  interface  for  the  router. The  router’s  LAN  IPv6  Address 
confi\buration  is  based  on  the  IPv6  Address  and  Subnet 
assi\bned by your ISP. (A subnet with prefix /64 is supported 
in LAN.)  
						

							57D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
The fo\f\fowin\b parameters wi\f\f be avai\fab\fe for confi\buration:
6rd IPv6 Prefix:Enter the 6rd IPv6 address and prefix va\fue used 
here.
IPv4 Address:Enter the IPv4 address used here.
Mask Length:Enter the IPv4 mask \fen\bth used h\uere.
Assigned IPv6 Prefix:Disp\fays the IPv6 assi\bned prefix va\fue here.
6rd Border Relay IPv4 
Address:
Enter the 6rd border re\fay IPv4 address used here.
IPv6 DNS Server:Enter the primary DNS Server address used here.
The IPv6 Internet Connection Setup Wizard is comp\fete. 
C\fick on the Connect button to continue. C\fick on the Prev button to return to 
the previous pa\be. C\fick on the Cance\b button to discard a\f\f the chan\bes made 
and return to the main pa\be.
Tunne\bing.Connection.(6rd)
After se\fectin\b the Tunne\fin\b Connection (6rd) option, the user \ucan confi\bure the IPv6 6rd connection settin\bs.  
						

							58D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
IPv6 Manual Setup
There are severa\f connection types to choose from: Auto Detection, Static IPv6, Autoconfi\buration (SLAAC/DHCPv6), PPPoE, 
IPv6 in IPv4 Tunne\f, 6to4, 6rd, and Link-\foca\f. If you are unsure of your connection method, p\fease contact your IPv6 Internet 
Service Provider. 
Note: If usin\b the PPPoE option, you wi\f\f need to ensure that any PPPoE c\fient software on your computers has been removed 
or disab\fed.
Auto Dete\ftion
Se\fect Auto.Detection  to  have  the  router  detect  and  automatica\f\fy 
confi\bure your IPv6 settin\b from your ISP.  
						

							59D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
Stati\f IPv6
Se\fect Static.IPv6 from the drop-down menu.
Enter the address settin\bs supp\fied by your Internet provider 
(ISP). 
Enter the LAN (\foca\f) I\uPv6 address for the router. 
Disp\fays the Router’s LAN Link-Loca\f Address.
Check to enab\fe the Autoconfi\buration feature.
Se\fect Statefu\b.(DHCPv6), SLAAC .+ .RDNSS  or SLAAC .+.
State\bess.DHCPv6. 
Enter the start IPv6 Address for the DHCPv6 ran\be for your 
\foca\f computers.
Enter  the  end  IPv6  Address  for  the  DHCPv6  ran\be  for  your 
\foca\f computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Conne\ftion:
WAN IPv6 Address 
Settings:
LAN IPv6 Address:
LAN Link-Lo\fal Address:
Enable 
Auto\fonfiguration:
Auto\fonfiguration Type:
IPv6 Address Range 
Start:
IPv6 Address Range 
End:
IPv6 Address Lifetime:  
						

							60D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
Auto\fonfiguration
Se\fect Autoconfiguration.(State\bess/DHCPv6)  from  the 
drop-down menu.
Se\fect either \fbtain. DNS.server. address. automatica\b\by or 
Use.the.fo\b\bowing.DNS.Address.
Enter the primary and secondary DNS server addresses. 
Enter the LAN (\foca\f) I\uPv6 address for the router. 
Disp\fays the Router’s LAN Link-Loca\f Address.
Check to enab\fe the Autoconfi\buration feature.
Se\fect Statefu\b.(DHCPv6), SLAAC .+ .RDNSS  or SLAAC .+.
State\bess.DHCPv6.  
Enter the start IPv6 Address for the DHCPv6 ran\be for your 
\foca\f computers.
Enter  the  end  IPv6  Address  for  the  DHCPv6  ran\be  for  your 
\foca\f computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Conne\ftion:
IPv6 DNS Settings:
Primary/Se\fondary DNS 
Address:
LAN IPv6 Address:
LAN Link-Lo\fal Address:
Enable 
Auto\fonfiguration:
Auto\fonfiguration Type:
IPv6 Address Range 
Start:
IPv6 Address Range 
End:
IPv6 Address Lifetime:  
						

							61D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
PPPoE
Se\fect PPPoE from the drop-down menu.
Enter  the  PPPoE  account  settin\bs  supp\fied  by  your  Internet 
provider (ISP). 
Se\fect Static if your ISP assi\bned you the IP address, subnet mask, 
\bateway, and DNS server addresses. In most cases, se\fect Dynamic.
Enter the IP address (Static PPPoE on\fy).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the 
next box.
Enter the ISP Service Name (optiona\f).
Se\fect either A\bways-on, \fn-Demand, or Manua\b.
Enter a maximum id\fe time durin\b which the Internet connection 
is  maintained  durin\b  inactivity.  To  disab\fe  this  feature,  enab\fe 
Auto-reconnect.
Maximum Transmission Unit - you may need to chan\be the MTU for 
optima\f performance with your specific ISP. 1492 is the defau\ft MTU.
Se\fect either \fbtain.DNS.server. address. automatica\b\by or Use.
the.fo\b\bowing.DNS.Address.
Enter the primary and secondary DNS server addresses. 
Enter the LAN (\foca\f) I\uPv6 address for the router. 
Disp\fays the Router’s LAN Link-Loca\f Address.
Check to enab\fe the Autoconfi\buration feature.
My IPv6 Conne\ftion:
PPPoE:
Address Mode:
IP Address:
User Name:
Password:
Servi\fe Name:
Re\fonne\ftion Mode:
Maximum Idle Time: 
MTU:
IPv6 DNS Settings:
Primary/Se\fondary DNS 
Address:
LAN IPv6 Address:
LAN Link-Lo\fal Address:
Enable Auto\fonfiguration:  
						

							62D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
Auto\fonfiguration Type:
IPv6 Address Range Start:
IPv6 Address Range End:
IPv6 Address Lifetime:
Se\fect Statefu\b.(DHCPv6), SLAAC.+.RDNSS or SLAAC.+.State\bess.DHCPv6.
Enter the start IPv6 Address for the DHCPv6 ran\be for your \foca\f computers.
Enter the end IPv6 Address for the DHCPv6 ran\be for your \foca\f computers.
Enter the IPv6 Address Lifetime (in minutes).  
						

							63D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
IPv6 in IPv4 Tunneling
Se\fect IPv6.in.IPv4.Tunne\b from the drop-down menu.
Enter the settin\bs supp\fi\ued by your Internet provider (ISP). 
Enter the LAN (\foca\f) I\uPv6 address for the router. 
Disp\fays the Router’s LAN Link-Loca\f Address.
Check to enab\fe the Autoconfi\buration feature.
Se\fect Statefu\b.(DHCPv6), SLAAC.+.RDNSS or SLAAC. +.State\bess.
DHCPv6. 
Enter  the  start  IPv6  Address  for  the  DHCPv6  ran\be  for  your  \foca\f 
computers.
Enter  the  end  IPv6  Address  for  the  DHCPv6  ran\be  for  your  \foca\f 
computers.
Enter the Router Advertisement Lifetime (in minutes).
My IPv6 
Conne\ftion:
IPv6 in IPv4 Tunnel 
Settings:
LAN IPv6 Address:
LAN Link-Lo\fal 
Address:
Enable 
Auto\fonfiguration:
Auto\fonfiguration 
Type:
IPv6 Address 
Range Start:
IPv6 Address 
Range End:
Pv6 Address 
Lifetime:  
						

							64D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
6 to 4 Tunneling
Se\fect 6.to.4 from the drop-down menu.
Enter the IPv6 settin\bs supp\fied \uby your Internet provider (ISP). 
Enter the primary and secondary DNS server addresses. 
Enter the LAN (\foca\f) I\uPv6 address for the router. 
Disp\fays the Router’s LAN Link-Loca\f Address.
Check to enab\fe the Autoconfi\buration feature.
Se\fect Statefu\b.(DHCPv6), SLAAC.+.RDNSS or SLAAC. +.State\bess.
DHCPv6. 
Enter  the  start  IPv6  Address  for  the  DHCPv6  ran\be  for  your  \foca\f 
computers.
Enter  the  end  IPv6  Address  for  the  DHCPv6  ran\be  for  your  \foca\f 
computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Conne\ftion:
6 to 4 Settings:
Primary/Se\fondary 
DNS Address:
LAN IPv6 Address:
LAN Link-Lo\fal 
Address:
Enable 
Auto\fonfiguration:
Auto\fonfiguration 
Type:
IPv6 Address Range 
Start:
IPv6 Address Range 
End:
IPv6 Address 
Lifetime:  
						

							65D-Link DIR-825 User Manua\f
Section 3 - Confi\buration
6rd
Se\fect 6rd from the drop-down menu.
Enter  the  address  settin\bs  supp\fied  by  your  Internet  provider 
(ISP). 
Enter the LAN (\foca\f) I\uPv6 address for the router. 
Disp\fays the Router’s LAN Link-Loca\f Address.
Check to enab\fe the Autoconfi\buration feature.
Se\fect Stateful (DHCPv6), SLAAC+RDNSS or SLAAC + Stateless 
DHCPv6. 
Enter the Router Advertisement Lifetime (in minutes).
My IPv6 Conne\ftion:
6RD Settings:
LAN IPv6 Address:
LAN Link-Lo\fal Address:
Enable 
Auto\fonfiguration:
Auto\fonfiguration Type:
Router Advertisement  
Lifetime: