Creative Studio 6 Manual

Phase 4 - Backgrounds211
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 211   |  Page Quilting the Quilt - Which CS Feature To use
E2E (Edge_To_Edge)Pantographs
Now you have enough information to start a new E2E Quilt group. Some people
prefer to begin back at the first row, and others prefer to begin in the middle,
pretending that a middle row is actually the top of the quilt. If you choose to do this,
be sure to adjust the quilt length accordingly....

Getting Started with CreativeStudio®
212
4.5.2 E2E Repeat Pattern Pantographs
Background patterns (pantographs) can be stitched using the Repeat Pattern
features. The benefit is  that Repeat Pattern is a more flexible feature, allowing
additional boundaries and patterns to be placed in the quilt group along with the
background pattern. The nice feature about E2E is the way CS controls the sizing
and repositioning of the patterns automatically when the quilt is rolled. With Repeat
Patterns, you do this...

Phase 4 - Backgrounds213
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 213   |  Page Quilting the Quilt - Which CS Feature To use
E2E Repeat Pattern Pantographs* Set Pattern Location Point = Upper Left Corner
* Move machine to the Pattern Location (Upper Left Corner in this example)
4.  Click OK. An image of your entire quilt appears in the Preview area. 
5.   This method for doing pantographs does not monitor how much area can be
quilted at one...

Getting Started with CreativeStudio®
214
Repeat allows you to use any of the special features you need - Trim, Fill, Combine,
Divide,Draw Sewable, etc. 
Roll the quilt. 
4.5.2.1
E2E Repeat Relocate
Relocate is needed to synchronize the quilt and the sewing head after rolling the
quilt. There are four methods for relocating, and  Relocate - Shift All to 2 Points
 is
shown here. 
Think about which two points are easily identifiable on both the Preview area of the
computer screen, and on the quilt top....

Phase 4 - Backgrounds215
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 215   |  Page Quilting the Quilt - Which CS Feature To use
E2E Repeat Pattern Pantographs
5.  Check the positioning by using the machine crosshairs. 
6.  Continue until the entire quilt is done. 
The last row may need some adjustments. Check this by drawing a boundary around
the last row, paying close attention to the bottom edge of the quilt. Use any/all tools
to adjust the...

Getting Started with CreativeStudio®
216
Assumptions:  The machine is threaded, bobbins wound, belts engaged and
patterns have been added to the project. The Prep Steps here are the same as a
standard E2E.  
Prep Step #1.)
 Measure the quilt length and width accurately before loading the
quilt. Note: There are three reasons to modify the total quilt length and width.
1. If you are leaving a margin at the top and bottom, be sure to reduce your total quilt length by
this amount. 
2. If your pattern is...

Phase 4 - Backgrounds217
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 217   |  Page Quilting the Quilt - Which CS Feature To use
E2E Alternating Patterns
Variable Settings : 
*  Select Between Blocks
 describes what you want CS to do between blocks.
Connect Start And End is preferred for pantographs.
Bobbin Pullup is used if each repeat is a separate block pattern. CS automatically
switches to Bobbin Pullup if the repeated patterns have become...

Getting Started with CreativeStudio®
218
5.  Click Quilt
   
   The machine moves to the start of the first pattern, takes a
single stitch and prompts you to pull up the bobbin, so do that. Press OK on the
keypad when ready. The first row now begins.
Repeat the steps listed in the previous section to complete the quilt. Be sure to trim
the bottom edge to fit.
Quick Reference E2E
4.5.4 E2E Concatenating Patterns
Edge To Edge patterns can be concatenated giving a very custom look. These
patterns must have...

Phase 4 - Backgrounds219
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 219   |  Page Quilting the Quilt - Which CS Feature To use
E2E Concatenating Patterns
3.  Click the E2E icon
.  
   and follow the prompts to define the boundary. 
4.  Enter the quilt length
  in the E2E Settings area and CS will display the patterns.
Here are examples of different combinations of the Ride Into The Sunset patterns. 

Getting Started with CreativeStudio®
220
Save the project .   
Follow the same steps as defined in the previous sections to stitch them.  Begin at
Step 5 of Pantographs using Edge-To-Edge. This will guide you through the steps of
quilting each row (and advancing the quilt) until done. 
67