Home > Compaq > Notebook > compaq evo notebook n800c series User Manual

compaq evo notebook n800c series User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual compaq evo notebook n800c series User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							A–4Maintenance and Service Guide
    Connector Pin Assignments
    Ta b l e  A - 5
    Parallel
    Pin Signal Pin Signal
    1 Strobe* 10 Acknowledge*
    2 Data bit 0 11 Busy
    3 Data bit 1 12 Paper out
    4 Data bit 2 13 Select
    5 Data bit 3 14 Auto line feed*
    6 Data bit 4 15 Error*
    7 Data bit 5 16 Initialize printer*
    8 Data bit 6 17 Select in*
    9 Data bit 7 18-25 Signal ground
    *Signal is active low.
    268135-002.book  Page 4  Thursday, October 24, 2002  4:10 PM 
    						
    							Connector Pin Assignments
    Maintenance and Service GuideA–5
    Ta b l e  A - 6
    External Monitor
    Pin Signal Pin Signal
    1 Red analog 9 +5 VDC
    2 Green analog 10 Ground
    3 Blue analog 11 Monitor detect
    4 Not connected 12 DDC 2B data
    5 Ground 13 Horizontal sync
    6 Ground analog 14 Vertical sync
    7 Ground analog 15 DDC 2B clock
    8 Ground analog
    268135-002.book  Page 5  Thursday, October 24, 2002  4:10 PM 
    						
    							A–6Maintenance and Service Guide
    Connector Pin Assignments
    Ta b l e  A - 7
    Stereo Speaker/Headphone
    Pin Signal Pin Signal
    1 Audio out 2 Ground
    Ta b l e  A - 8
    Microphone
    Pin Signal Pin Signal
    1 Audio in 2 Ground
    268135-002.book  Page 6  Thursday, October 24, 2002  4:10 PM 
    						
    							Maintenance and Service GuideB–1
    B
    Power Cord Set Requirements
    3-Conductor Power Cord Set
    The computer’s wide range input feature permits it to operate 
    from any line voltage from 100 to 120 or 220 to 240 volts AC.
    The power cord set received with the computer meets the 
    requirements for use in the country where the equipment is 
    purchased.
    Power cord sets for use in other countries must meet the 
    requirements of the country where the computer is used. For more 
    information on power cord set requirements, contact a Compaq 
    authorized reseller or service provider.
    General Requirements
    The requirements listed below are applicable to all countries:
    ■The length of the power cord set must be at least 5.00 feet 
    (1.5 m) and a maximum of 6.50 feet (2.0 m).
    ■All power cord sets must be approved by an acceptable 
    accredited agency responsible for evaluation in the country 
    where the power cord set will be used.
    ■The power cord set must have a minimum current capacity of 
    10 amps and a nominal voltage rating of 125 or 250 volts AC, 
    as required by each country’s power system.
    ■The appliance coupler must meet the mechanical 
    configuration of an EN 60 320/IEC 320 Standard Sheet C13 
    connector, for mating with the appliance inlet on the back of 
    the computer.
    268135-002.book  Page 1  Thursday, October 24, 2002  4:10 PM 
    						
    							B–2Maintenance and Service Guide
    Power Cord Set Requirements
    Country-Specific Requirements
    3-Conductor Power Cord Set Requirements
    Country Accredited Agency Applicable Note Number
    Australia EANSW 1
    Austria OVE 1
    Belgium CEBC 1
    Canada CSA 2
    Denmark DEMKO 1
    Finland FIMKO 1
    France UTE 1
    Germany VDE 1
    Italy IMQ 1
    Japan METI 3
    The Netherlands KEMA 1
    Norway NEMKO 1
    Sweden SEMKO 1
    Switzerland SEV 1
    United Kingdom BSI 1
    United States UL 2
    268135-002.book  Page 2  Thursday, October 24, 2002  4:10 PM 
    						
    							Power Cord Set Requirements
    Maintenance and Service GuideB–3
    Notes
    1. The flexible cord must be  Type HO5VV-F, 
    3-conductor, 1.0 mm
    2 conductor size. Power cord set fittings 
    (appliance coupler and wall plug) must bear the certification 
    mark of the agency responsible for evaluation in the country 
    where it will be used.
    2. The flexible cord must be Type SPT-3 or equivalent, No. 18 
    AWG, 3-conductor. The wall plug must be a two-pole 
    grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 
    6-15P (15 A, 250 V) configuration.
    3. The appliance coupler, flexible cord, and wall plug must bear 
    a “T” mark and registration number in accordance with the 
    Japanese Dentori Law. The flexible cord must be Type VCT 
    or VCTF, 3-conductor, 1.00 mm
    2 conductor size. The wall 
    plug must be a two-pole grounding type with a Japanese 
    Industrial Standard C8303 (7 A, 125 V) configuration.
    268135-002.book  Page 3  Thursday, October 24, 2002  4:10 PM 
    						
    							Maintenance and Service GuideC–1
    C
    Screw Listing
    This appendix provides specification and reference information 
    for the screws used in the computer. All screws listed in this 
    appendix are available in the Miscellaneous Screw Kit, spare part 
    number 285290-001.
    268135-002.book  Page 1  Thursday, October 24, 2002  4:10 PM 
    						
    							C–2Maintenance and Service Guide
    Screw Listing
    Figure C-1. Phillips M3.0 × 4.0 Screw Location
    Ta b l e  C - 1
    Phillips M3.0 × 4.0 Screw
    Color Qty. Length ThreadHead 
    Width
    Black 3 4.0 mm 3.0 mm 5.0 mm
    Where used:
    One screw that secures the hard drive to the computer
    (documented in Section 5.3)
    268135-002.book  Page 2  Thursday, October 24, 2002  4:10 PM 
    						
    							Screw Listing
    Maintenance and Service GuideC–3
    Figure C-2. Phillips M3.0 × 4.0 Screw Locations
    Ta b l e  C - 1
    Phillips M3.0 × 4.0 Screw (Continued)
    Color Qty. Length ThreadHead 
    Width
    Black 3 4.0 mm 3.0 mm 5.0 mm
    Where used:
    Two screws that secure the hard drive bezel to the hard drive
    (documented in Section 5.3)
    268135-002.book  Page 3  Thursday, October 24, 2002  4:10 PM 
    						
    							C–4Maintenance and Service Guide
    Screw Listing
    Figure C-3. Phillips M2.0 × 5.5 Screw Locations
    Ta b l e  C - 2
    Phillips M2.0 × 5.5 Screw
    Color Qty. Length ThreadHead 
    Width
    Silver 2 5.5 mm 2.0 mm 4.0 mm
    Where used:
    Two screws that secure the connector cover to the computer
    (documented in Section 5.7)
    268135-002.book  Page 4  Thursday, October 24, 2002  4:10 PM 
    						
    All Compaq manuals Comments (0)

    Related Manuals for compaq evo notebook n800c series User Manual