compaq evo notebook n800 xx series User Manual

							Connector Pin Assignments
Maintenance and Service GuideA–3
Ta b l e  A - 4
S-Video
Pin Signal Pin Signal
1 Ground (Y) 3 Y-Luminance (Intensity)
2 Ground (C) 4 C-Chrominance (Color)
268135-003.book  Page 3  Thursday, January 30, 2003  9:12 AM 
						

							A–4Maintenance and Service Guide
Connector Pin Assignments
Ta b l e  A - 5
Parallel
Pin Signal Pin Signal
1 Strobe* 10 Acknowledge*
2 Data bit 0 11 Busy
3 Data bit 1 12 Paper out
4 Data bit 2 13 Select
5 Data bit 3 14 Auto line feed*
6 Data bit 4 15 Error*
7 Data bit 5 16 Initialize printer*
8 Data bit 6 17 Select in*
9 Data bit 7 18-25 Signal ground
*Signal is active low.
114
25
13
268135-003.book  Page 4  Thursday, January 30, 2003  9:12 AM 
						

							Connector Pin Assignments
Maintenance and Service GuideA–5
Ta b l e  A - 6
External Monitor
Pin Signal Pin Signal
1 Red analog 9 +5 VDC
2 Green analog 10 Ground
3 Blue analog 11 Monitor detect
4 Not connected 12 DDC 2B data
5 Ground 13 Horizontal sync
6 Ground analog 14 Vertical sync
7 Ground analog 15 DDC 2B clock
8 Ground analog
1 6115 1015
268135-003.book  Page 5  Thursday, January 30, 2003  9:12 AM 
						

							A–6Maintenance and Service Guide
Connector Pin Assignments
Ta b l e  A - 7
Stereo Speaker/Headphone
Pin Signal Pin Signal
1 Audio out 2 Ground
21
Ta b l e  A - 8
Microphone
Pin Signal Pin Signal
1 Audio in 2 Ground
21
268135-003.book  Page 6  Thursday, January 30, 2003  9:12 AM 
						

							Maintenance and Service GuideB–1
B
Power Cord Set Requirements
3-Conductor Power Cord Set
The computer’s wide range input feature permits it to operate 
from any line voltage from 100 to 120 or 220 to 240 volts AC.
The power cord set received with the computer meets the 
requirements for use in the country where the equipment is 
purchased.
Power cord sets for use in other countries must meet the 
requirements of the country where the computer is used. For more 
information on power cord set requirements, contact a Compaq 
authorized reseller or service provider.
General Requirements
The requirements listed below are applicable to all countries:
■The length of the power cord set must be at least 5.00 feet 
(1.5 m) and a maximum of 6.50 feet (2.0 m).
■All power cord sets must be approved by an acceptable 
accredited agency responsible for evaluation in the country 
where the power cord set will be used.
■The power cord set must have a minimum current capacity of 
10 amps and a nominal voltage rating of 125 or 250 volts AC, 
as required by each country’s power system.
■The appliance coupler must meet the mechanical 
configuration of an EN 60 320/IEC 320 Standard Sheet C13 
connector, for mating with the appliance inlet on the back of 
the computer.
268135-003.book  Page 1  Thursday, January 30, 2003  9:12 AM 
						

							B–2Maintenance and Service Guide
Power Cord Set Requirements
Country-Specific Requirements
3-Conductor Power Cord Set Requirements
Country Accredited Agency Applicable Note Number
Australia EANSW 1
Austria OVE 1
Belgium CEBC 1
Canada CSA 2
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
Italy IMQ 1
Japan METI 3
The Netherlands KEMA 1
Norway NEMKO 1
Sweden SEMKO 1
Switzerland SEV 1
268135-003.book  Page 2  Thursday, January 30, 2003  9:12 AM 
						

							Power Cord Set Requirements
Maintenance and Service GuideB–3
United Kingdom BSI 1
United States UL 2
Notes
1. The flexible cord must be  Type HO5VV-F, 3-conductor, 1.0 mm
2 
conductor size. Power cord set fittings (appliance coupler and wall plug) 
must bear the certification mark of the agency responsible for evaluation in 
the country where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 
3-conductor. The wall plug must be a two-pole grounding type with a 
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark 
and registration number in accordance with the Japanese Dentori Law. 
The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm
2 
conductor size. The wall plug must be a two-pole grounding type with a 
Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
3-Conductor Power Cord Set Requirements
Country Accredited Agency Applicable Note Number
268135-003.book  Page 3  Thursday, January 30, 2003  9:12 AM 
						

							Maintenance and Service GuideC–1
C
Screw Listing
This appendix provides specification and reference information 
for the screws used in the computer. All screws listed in this 
appendix are available in the Miscellaneous Screw Kit, spare part 
number 285290-001.
268135-003.book  Page 1  Thursday, January 30, 2003  9:12 AM 
						

							C–2Maintenance and Service Guide
Screw Listing
Figure C-1. Phillips M3.0 × 4.0 Screw Location
Ta b l e  C - 1
Phillips M3.0 × 4.0 Screw
Color Qty. Length ThreadHead 
Width
Black 3 4.0 mm 3.0 mm 5.0 mm
Where used:
One screw that secures the hard drive to the computer
(documented in Section 5.3)
268135-003.book  Page 2  Thursday, January 30, 2003  9:12 AM 
						

							Screw Listing
Maintenance and Service GuideC–3
Figure C-2. Phillips M3.0 × 4.0 Screw Locations
Ta b l e  C - 1
Phillips M3.0 × 4.0 Screw (Continued)
Color Qty. Length ThreadHead 
Width
Black 3 4.0 mm 3.0 mm 5.0 mm
Where used:
Two screws that secure the hard drive bezel to the hard drive
(documented in Section 5.3)
268135-003.book  Page 3  Thursday, January 30, 2003  9:12 AM