compaq evo notebook n1020v series User Manual

							Maintenance and Service GuideC–5
Figure C-4. TM2.5 × 5.0 Screw Locations
Ta b l e  C - 1
Torx T8 Metric 2.5 × 5.0 Screw (Continued)
Color Qty Length ThreadHead 
Width
Silver 30 5.0 mm 2.5 mm 5.0 mm
Where used:
One screw that secures the display inverter cable ground loop to the heat 
spreader (documented in Section 5.13) 
						

							C–6Maintenance and Service Guide
Figure C-5. TM2.5 × 5.0 Screw Locations
Ta b l e  C - 1
Torx T8 Metric 2.5 × 5.0 Screw (Continued)
Color Qty Length ThreadHead 
Width
Silver 30 5.0 mm 2.5 mm 5.0 mm
Where used:
1 Three screws that secure the diskette drive to the palm rest
(documented in Section 5.15)
2 TouchPad only models—Four screws that secure the TouchPad 
components to the palm rest (documented in Section 5.16)
2 Dual Stick models—Five screws that secure the TouchPad components to 
the palm rest (documented in Section 5.16)
3 Two screws that secure the display release assembly to the palm rest
(documented in Section 5.17) 
						

							Maintenance and Service GuideC–7
Figure C-6. TM2.5 × 5.0 Screw Locations
Ta b l e  C - 1
Torx T8 Metric 2.5 × 5.0 Screw (Continued)
Color Qty Length ThreadHead 
Width
Silver 30 5.0 mm 2.5 mm 5.0 mm
Where used:
Three screws that secure the charger board and shield to the base enclosure
(documented in Section 5.18) 
						

							C–8Maintenance and Service Guide
Figure C-7. TM2.5 × 5.0 Screw Locations
Ta b l e  C - 1
Torx T8 Metric 2.5 × 5.0 Screw (Continued)
Color Qty Length ThreadHead 
Width
Silver 30 5.0 mm 2.5 mm 5.0 mm
Where used:
Three screws that secure the top cover to the base enclosure
(documented in Section 5.20) 
						

							Maintenance and Service GuideC–9
Figure C-8. TM2.5 × 5.0 Screw Locations
Ta b l e  C - 1
Torx T8 Metric 2.5 × 5.0 Screw (Continued)
Color Qty Length ThreadHead 
Width
Silver 30 5.0 mm 2.5 mm 5.0 mm
Where used:
1 Two screws that secure the optical drive front alignment rail to the base 
enclosure (documented in Section 5.22)
2 Two screws that secure the optical drive rear alignment rail to the base 
enclosure (documented in Section 5.22)
3 Three screws that secure the system board to the base enclosure 
(documented in Section 5.22) 
						

							C–10Maintenance and Service Guide
Figure C-9. TM2.5 × 8.0 Screw Locations
Ta b l e  C - 2
Torx T8 Metric 2.5 × 8.0 Screw
Color Qty Length ThreadHead 
Width
Silver 11 8.0 mm 2.5 mm 4.0 mm
Where used:
1 One screw that secures the hard drive to the base enclosure
(documented in Section 5.3)
2 Two screws that secure the LED cover to the base enclosure
(documented in Section 5.9)
3 Five screws that secure the palm rest to the base enclosure
(documented in Section 5.14)
4 Two screws that secure the top cover to the base enclosure
(documented in Section 5.20) 
						

							Maintenance and Service GuideC–11
Figure C-10. TM2.5 × 8.0 Screw Locations
Ta b l e  C - 2
Torx T8 Metric 2.5 × 8.0 Screw (Continued)
Color Qty Length ThreadHead 
Width
Silver 11 8.0 mm 2.5 mm 4.0 mm
Where used:
One screw that secures the heat spreader to the base enclosure
(documented in Section 5.11) 
						

							C–12Maintenance and Service Guide
Figure C-11. PM3.0 × 3.0 Screw Locations
Ta b l e  C - 3
Phillips Metric 3.0 × 3.0 Screw
Color Qty Length ThreadHead 
Width
Silver 4 3.0 mm 3.0 mm 5.0 mm
Where used:
Four screws that secure the hard drive to the hard drive bracket
(documented in Section 5.3) 
						

							Maintenance and Service GuideC–13
Figure C-12. PM2.5 × 4.0 Screw Locations
Ta b l e  C - 4
Phillips Metric 2.5 × 4.0 Screw
Color Qty Length ThreadHead 
Width
Silver 2 4.0 mm 2.5 mm 5.0 mm
Where used:
1 One screw that secures the memory expansion compartment cover to the 
base enclosure (documented in Section 5.5)
2 One screw that secures the mini PCI compartment cover to the base 
enclosure (documented in Section 5.6) 
						

							C–14Maintenance and Service Guide
Figure C-13. TM2.5 × 14.0 Shoulder Screw Locations
Ta b l e  C - 5
Torx T8 Metric 2.5 × 14.0 Shoulder Screw
Color Qty Length ThreadHead 
Width
Silver 4 14.0 mm 2.0 mm 6.0 mm
Where used:
Four screws that secure the heat spreader to the base enclosure
(documented in Section 5.11)