compaq evo notebook n1000 series User Manual

							Specifications
Maintenance and Service Guide6–19
I/O Address (hex)System Function (shipping configuration)
2F0 - 2F7 Unused
2F8 - 2FF Infrared port
300 - 31F Unused
320 - 36F Unused
370 - 377 Secondary diskette drive controller
378 - 37F Parallel port (LPT1/default)
380 - 387 Unused
388 - 38B FM synthesizer - OPL3
38C - 3AF Unused
3B0 - 3BB VGA
3BC - 3BF Reserved (parallel port/no EPP support)
3C0 - 3DF VGA
3E0 - 3E1 PC Card controller in CPU
3E2 - 3E3 Unused
3E8 - 3EF Internal modem
3F0 - 3F7 “A” diskette controller
3F8 - 3FF Serial port (COM1/default)
CF8 - CFB PCI configuration index register (PCIDIVO-1)
CFC - CFF PCI configuration data register (PCIDIVO-1)
Table 6-15
System I/O Addresses (Continued)
279372-001.book  Page 19  Friday, July 19, 2002  11:50 AM 
						

							6–20Maintenance and Service Guide
Specifications
Table 6-16
System Memory Map
Size Memory Address System Function
640 KB 00000000 - 0009FFFF Base memory
128 KB 000A0000 - 000BFFFF Video memory
48 KB 000C0000 - 000CBFFF Video BIOS
160 KB 000C8000 - 000E7FFF Unused
64 KB 000E8000 - 000FFFFF System BIOS
15 MB 00100000 - 00FFFFFF Extended memory
58 MB 01000000 - 047FFFFFSuper extended memory
58 MB 04800000 - 07FFFFFF Unused
2 MB 08000000 - 080FFFFF Video memory (direct access)
4 GB 08200000 - FFFEFFFF Unused
64 KB FFFF0000 - FFFFFFFF System BIOS
279372-001.book  Page 20  Friday, July 19, 2002  11:50 AM 
						

							Maintenance and Service GuideA–1
A
Connector Pin Assignments
Ta b l e  A - 1
RJ-45 Network Interface
Pin Signal Pin Signal
1 Transmit + 5 Unused
2 Transmit - 6 Receive -
3 Receive + 7 Unused
4Unused 8Unused
6 5
4 3
2 1
7
8
279372-001.book  Page 1  Friday, July 19, 2002  11:50 AM 
						

							A–2Maintenance and Service Guide
Connector Pin Assignments
Ta b l e  A - 2
RJ-11 Modem
Pin Signal Pin Signal
1Unused 4Unused
2 Tip 5 Unused
3Ring 6Unused
Ta b l e  A - 3
Universal Serial Bus
Pin Signal Pin Signal
1 +5 VDC 3 Data +
2 Data - 4 Ground
279372-001.book  Page 2  Friday, July 19, 2002  11:50 AM 
						

							Connector Pin Assignments
Maintenance and Service GuideA–3
Ta b l e  A - 4
S-Video
Pin Signal Pin Signal
1 Ground (Y) 3 Y-Luminance (Intensity)
2 Ground (C) 4 C-Chrominance (Color)
Ta b l e  A - 5
External Keyboard/Mouse
Pin Signal Pin Signal
1 Keyboard/mouse DATA 4 +5 VDC
2 Keyboard/mouse DATA 5 Keyboard/mouse CLK
3 Ground 6 Keyboard/mouse CLK
KEY
6 54 32 1
279372-001.book  Page 3  Friday, July 19, 2002  11:50 AM 
						

							A–4Maintenance and Service Guide
Connector Pin Assignments
Ta b l e  A - 6
Parallel
Pin Signal Pin Signal
1 Strobe* 10 Acknowledge*
2 Data bit 0 11 Busy
3 Data bit 1 12 Paper out
4 Data bit 2 13 Select
5 Data bit 3 14 Auto line feed*
6 Data bit 4 15 Error*
7 Data bit 5 16 Initialize printer*
8 Data bit 6 17 Select in*
9 Data bit 7 18-25 Signal ground
*Signal is active low.
114
25
13
279372-001.book  Page 4  Friday, July 19, 2002  11:50 AM 
						

							Connector Pin Assignments
Maintenance and Service GuideA–5
Ta b l e  A - 7
External Monitor
Pin Signal Pin Signal
1 Red analog 9 +5 VDC
2 Green analog 10 Ground
3 Blue analog 11 Monitor detect
4 Not connected 12 DDC 2B data
5 Ground 13 Horizontal sync
6 Ground analog 14 Vertical sync
7 Ground analog 15 DDC 2B clock
8 Ground analog
1 6115 1015
279372-001.book  Page 5  Friday, July 19, 2002  11:50 AM 
						

							A–6Maintenance and Service Guide
Connector Pin Assignments
Ta b l e  A - 8
Stereo Speaker/Headphone
Pin Signal Pin Signal
1 Audio out 2 Ground
21
Ta b l e  A - 9
Microphone
Pin Signal Pin Signal
1 Audio in 2 Ground
21
279372-001.book  Page 6  Friday, July 19, 2002  11:50 AM 
						

							Maintenance and Service GuideB–1
B
Power Cord Set Requirements
3-Conductor Power Cord Set
The wide range input feature of the notebook permits it to operate 
from any line voltage from 100 to 120 or 220 to 240 volts AC.
The power cord set received with the computer meets the 
requirements for use in the country where the equipment is 
purchased.
Power cord sets for use in other countries must meet the 
requirements of the country where the computer is used. For more 
information on power cord set requirements, contact a Compaq 
authorized reseller or service provider.
General Requirements
The requirements listed below are applicable to all countries:
■The length of the power cord set must be at least 1.5 m 
(5.00 feet) and no more than 2.0 m (6.50 feet).
■All power cord sets must be approved by an acceptable 
accredited agency responsible for evaluation in the country 
where the power cord set will be used.
■The power cord set must have a minimum current capacity of 
10 amperes and a nominal voltage rating of 125 or 250 volts 
AC, as required by each country’s power system.
■The appliance coupler must meet the mechanical 
configuration of an EN 60 320/IEC 320 Standard Sheet C13 
connector, for mating with the appliance inlet on the back of 
the computer.
279372-001.book  Page 1  Friday, July 19, 2002  11:50 AM 
						

							B–2Maintenance and Service Guide
Power Cord Set Requirements
Country-Specific Requirements
3-Conductor Power Cord Set Requirements
Country Accredited Agency Applicable Note Number
Australia EANSW 1
Austria OVE 1
Belgium CEBC 1
Canada CSA 2
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
Italy IMQ 1
Japan METI 3
The Netherlands KEMA 1
Norway NEMKO 1
Sweden SEMKO 1
Switzerland SEV 1
279372-001.book  Page 2  Friday, July 19, 2002  11:50 AM