compaq evo n610c and evo n600c User Manual

							Connector Pin Assignments
Maintenance and Service GuideA–9
Ta b l e  A - 1 0
Docking (Continued)
Pin Signal Pin Signal
91 PS2 VCC 106 GND
92 SERIRQ 107 AD[15]
93 PS2 CLK 108 AD[13]
94 EXPREQ 109 AD[11]
95 AD[29] 110 AD[09]
96 AD[31] 111 GND
97 AD[30] 112 AD[06]
98 AD[28] 113 AD[04]
99 AD[26] 114 AD[02]
100 GND 115 AD[00]
101 AD[24] 116 GND
102 AD[22] 117 FRAME
103 AD[20] 118 TRDY
104 AD[18] 119 STOP
105 AD[16] 120 PAR
31
61
911
120 90 60 30
279362-001.book  Page 9  Monday, July 8, 2002  11:49 AM 
						

							Maintenance and Service GuideB–1
B
Power Cord Set Requirements
3-Conductor Power Cord Set
The wide range input feature of the notebook permits it to operate 
from any line voltage from 100 to 120 or 220 to 240 volts AC.
The power cord set received with the notebook meets the 
requirements for use in the country where the equipment is 
purchased.
Power cord sets for use in other countries must meet the 
requirements of the country where the notebook is used. For more 
information on power cord set requirements, contact a Compaq 
authorized reseller or service provider.
General Requirements
The requirements listed below are applicable to all countries:
■The length of the power cord set must be at least 1.5 m 
(5.00 feet) and a maximum of 2.0 m (6.50 feet).
■All power cord sets must be approved by an acceptable 
accredited agency responsible for evaluation in the country 
where the power cord set will be used.
■The power cord set must have a minimum current capacity 
of 10 amperes and a nominal voltage rating of 125 or 
250 volts AC, as required by each country’s power system.
■The appliance coupler must meet the mechanical 
configuration of an EN 60 320/IEC 320 Standard Sheet C13 
connector, for mating with the appliance inlet on the back of 
the notebook.
279362-001.book  Page 1  Monday, July 8, 2002  11:49 AM 
						

							B–2Maintenance and Service Guide
Power Cord Set Requirements
Country-Specific Requirements
3-Conductor Power Cord Set Requirements
Country Accredited Agency Applicable Note Number
Australia EANSW 1
Austria OVE 1
Belgium CEBC 1
Canada CSA 2
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
Italy IMQ 1
Japan METI 3
The Netherlands KEMA 1
Norway NEMKO 1
Sweden SEMKO 1
Switzerland SEV 1
279362-001.book  Page 2  Monday, July 8, 2002  11:49 AM 
						

							Power Cord Set Requirements
Maintenance and Service GuideB–3
United Kingdom BSI 1
United States UL 2
Notes
1. The flexible cord must be  Type HO5VV-F, 3-conductor, 1.0 mm
2 
conductor size. The power cord set fittings (appliance coupler and wall plug) 
must bear the certification mark of the agency responsible for evaluation in 
the country where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 
3-conductor. The wall plug must be a two-pole grounding type with a 
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and 
registration number in accordance with the Japanese Dentori Law. The 
flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm
2 conductor 
size. The wall plug must be a two-pole grounding type with a Japanese 
Industrial Standard C8303 (7 A, 125 V) configuration.
3-Conductor Power Cord Set Requirements
Country Accredited Agency Applicable Note Number
279362-001.book  Page 3  Monday, July 8, 2002  11:49 AM 
						

							Maintenance and Service GuideC–1
C
Screw Listing
This appendix provides specification and reference information 
for the screws used in the notebook. All screws listed in this 
appendix are available in the Miscellaneous Screw Kit, spare part 
number 241440-001.
279362-001.book  Page 1  Monday, July 8, 2002  11:49 AM 
						

							C–2Maintenance and Service Guide
Figure C-1. PM2.5 × 2.5 Screw Location
Ta b l e  C - 1
Phillips Metric 2.5 × 2.5 Screw
Color Qty Length ThreadHead 
Width
Black 1 2.5 mm 2.5 mm 5.0 mm
Where used:
One screw that secures the hard drive to the base enclosure
(documented in Section 5.3)
279362-001.book  Page 2  Monday, July 8, 2002  11:49 AM 
						

							Maintenance and Service GuideC–3
Figure C-2. PM1.5 × 3.5 Screw Location
Ta b l e  C - 2
Phillips Metric 1.5 × 3.5 Screw
Color Qty Length ThreadHead 
Width
Black 2 1.5 mm 3.5 mm 3.0 mm
Where used:
Two screws that secure the hard drive bezel to the hard drive
(documented in Section 5.3)
279362-001.book  Page 3  Monday, July 8, 2002  11:49 AM 
						

							C–4Maintenance and Service Guide
Figure C-3. PM2.5 × 5.5 Screw Location
Ta b l e  C - 3
Phillips Metric 2.5 × 5.0 Screw
Color Qty Length ThreadHead 
Width
Black 3 5.0 mm 2.5 mm 4.5 mm
Where used:
Evo Notebook N600c models—Two screws that secure the memory 
expansion compartment cover to the base enclosure
Evo Notebook N610c models—Two screws that secure the mini PCI 
compartment cover to the base enclosure (documented in Section 5.5)
279362-001.book  Page 4  Monday, July 8, 2002  11:49 AM 
						

							Maintenance and Service GuideC–5
Figure C-4. PM2.5 × 5.5 Screw Location (Continued)
Ta b l e  C - 3
Phillips Metric 2.5 × 5.0 Screw (Continued)
Color Qty Length ThreadHead 
Width
Black 3 5.0 mm 2.5 mm 4.5 mm
Where used:
Evo Notebook N610c models—One screw that secures the fan to the heat 
sink (documented in Section 5.14)
279362-001.book  Page 5  Monday, July 8, 2002  11:49 AM 
						

							C–6Maintenance and Service Guide
Figure C-5. TM2.5 × 7.0 Screw Locations
Ta b l e  C - 4
Torx T8 Metric 2.5 × 7.0 Screw
Color Qty Length ThreadHead 
Width
Black 12 7.0 mm 2.5 mm 5.0 mm
Where used:
1 One screw that secures the keyboard to the base enclosure
(documented in Section 5.7)
2 Three screws that secure the top cover to the base enclosure
(documented in Section 5.12)
279362-001.book  Page 6  Monday, July 8, 2002  11:49 AM