compaq evo n610c and evo n600c User Manual

							5–2Maintenance and Service Guide
Removal and Replacement Procedures
5.1 Serial Number
Report the notebook serial number to Compaq when requesting 
information or ordering spare parts. The serial number is located 
on the bottom of the notebook (Figure 5-1).
Figure 5-1. Serial Number Location
5.2 Disassembly Sequence Chart
Use the chart below to determine the section number to be 
referenced when removing notebook components.
Disassembly Sequence Chart
Section Description# of Screws 
Removed
5.3 Preparing the Notebook for Disassembly
Battery Pack 0
279362-001.book  Page 2  Monday, July 8, 2002  11:49 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–3
Section Description# of Screws 
Removed
5.3 Preparing the Notebook for Disassembly 
(Continued)
Media Bay Device 0
Hard Drive 1 to remove 
hard drive
2 to remove 
hard drive 
bezel
5.4 Computer Feet 0
5.5 Mini PCI Communications Board 2
5.6 Disk Cell RTC Battery 0
5.7 Keyboard 1
5.8 Memory Expansion 0
5.9 TouchPad 0
5.10 Switch Cover 2
5.11 Display 3
5.12 Top Cover 12
5.13 System Board 5
5.14 Fan 3
5.15 Heat Sink (Evo Notebook N610c models only) 6
5.16 Processor (Evo Notebook N610c models only) 0
5.17 DC-DC Converter Board 0
5.18 Modem Cable 0
Disassembly Sequence Chart (Continued)
279362-001.book  Page 3  Monday, July 8, 2002  11:49 AM 
						

							5–4Maintenance and Service Guide
Removal and Replacement Procedures
5.3 Preparing the Notebook for 
Disassembly
Perform the following steps before disassembling the notebook:
1. Turn off the notebook.
2. Disconnect the AC adapter and all external devices.
3. Remove the battery pack by following these steps:
a. Turn the notebook bottom side up with the front facing 
forward.
Battery Pack, 6-cell, Li ion
Spare Part Number Information
Battery packs, 6-cell, Li ion 232633-001 
and 
301952-001
279362-001.book  Page 4  Monday, July 8, 2002  11:49 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–5
b. Slide the battery release latch 1 toward the back of the 
notebook (Figure 5-2).
c. Swing the right side of the battery pack up and to the 
left
2.
d. Remove the battery pack 
3.
Figure 5-2. Removing the Battery Pack
Reverse the preceding procedure to install the battery pack.
279362-001.book  Page 5  Monday, July 8, 2002  11:49 AM 
						

							5–6Maintenance and Service Guide
Removal and Replacement Procedures
Media Bay Devices
Spare Part Number Information
For use with all Evo Notebook N610c and
Evo Notebook N600c models:
Diskette drive
24X Max CD-ROM drive
8X Max CD-RW drive
8X Max DVD-ROM drive
DVD/CD-RW combination drive
2X Max SuperDisk LS120 drive
IOmega 250-MB ZIP drive
6-cell battery pack135233-001
228746-001 
and 
228746-001
153992-001
173949-001
238878-001
201274-001
218683-001
100680-001 
and 
280876-001
For use with Evo Notebook N610c models only:
16X Max CD-RW drive
24X Max DVD/CD-RW combination drive274419-001
274420-001
279362-001.book  Page 6  Monday, July 8, 2002  11:49 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–7
4. Remove a Media Bay device by following these steps:
a. Turn the notebook bottom side up with the left side 
facing forward.
b. Slide and hold the Media Bay release latch toward the 
back of the notebook 
1 (Figure 5-3).
c. Use the notch in the Media Bay device to slide the device 
out of the Media Bay 
2.
Figure 5-3. Removing a Media Bay Device
Reverse the preceding procedure to install the Media Bay device.
279362-001.book  Page 7  Monday, July 8, 2002  11:49 AM 
						

							5–8Maintenance and Service Guide
Removal and Replacement Procedures
5. Remove the hard drive by following these steps:
a. Turn the notebook bottom side up with the right side 
facing forward.
Hard Drive
Spare Part Number Information
For use with Evo Notebook N610c models only:
40 GB
30 GB
20 GB
For use with Evo Notebook N600c models only:
30 GB
20 GB
15 GB
10 GB265495-001
257660-001 
235540-101
217096-001
235421-001
241429-001
217094-001
279362-001.book  Page 8  Monday, July 8, 2002  11:49 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–9
b. Remove the PM2.5 × 2.5 hard drive retention screw 1 
(Figure 5-4).
c. Separate the hard drive bezel 
2.
d. Use the bezel to slide the hard drive forward 
3 to unseat 
the hard drive connector from the system board.
e. Remove the hard drive.
Figure 5-4. Removing the Hard Drive
Reverse the preceding procedure to install the hard drive.
279362-001.book  Page 9  Monday, July 8, 2002  11:49 AM 
						

							5–10Maintenance and Service Guide
Removal and Replacement Procedures
6. Loosen the two PM1.5 × 3.5 screws 1 that secure the hard 
drive bezel to the hard drive (Figure 5-5).
7. Remove the hard drive bezel from the hard drive 
2.
Figure 5-5. Removing the Hard Drive Bezel
✎The hard drive bezel is included in the Miscellaneous Plastics Kit, 
spare part number 241439-001.
279362-001.book  Page 10  Monday, July 8, 2002  11:49 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–11
5.4 Computer Feet
The notebook feet are adhesive-backed rubber pads. The 
notebook feet are included in the Miscellaneous Plastics Kit 
(spare part number 241439-001). Refer to Figure 5-6 for 
notebook feet locations.
Figure 5-6. Replacing the Notebook Feet
279362-001.book  Page 11  Monday, July 8, 2002  11:49 AM