Comdial Solo II Telephone User Guide

COMDlAL 
Solo II 
TeleDhone 
User’s 
Guide 
:’ 
This publication is applicable for the following 
Solo II Telephone models: 
5531 -xx Manufacturing Code REV E and Later 
5531 S-xx Manufacturing Code REV F and Later 
5432X-xx Manufacturing Code REV A and Later 
15432S-xx Manufacturing Code REV A and Later  

Table of Contents 
BASIC OPERATION 
OPTIONS 
Speakerphone operation ~~~~,,~~~~~~..~...~~~~,~~,,~..~~.~~~~~~~~~~~~~~~ 1 1 
. . . 
111  

/ HANDSET CORD JACK 
SPKR KEY 
SPEUERPHOHE YOrEL51 
.MUERPHOWE OH/OFF / MONITOR KEY - 
. HAWOSFREE CKL YO”ITOR,Y 
. DO “OT DISTURB 
II/ I I \lI‘an 
II L-ii I 
PULL OUT DIRECTORY MICROPHONE OPENING 
ISPEhxE(ERPHO”E YOULSl 
STATION 
LINE KEYS- POWER SUPPLY 
‘L’NE ’ KEY ON LEFT’ TRANSFORMER 
. Ew8l.E CO”FERE”C,“O 
TELEPHONE POWER CORD 
Solo II Controls and Indicators  

Basic Operation 
BASIC OPEl?ATlON 
PLACING A CALL 
On Hook 
l Press line key. Listen for dial tone. 
l Dial number. 
l Lift handset when party answers. 
l Hang up handset to end call. 
Off Hook 
l Lift handset. 
l Press line key. (This step is not necessary if idle 
line preference has been assigned to station.) 
l Listen for dial tone. 
l Dial number. 
l Hang up handset to end call. 
ANSWERING A CALL 
l Press flashing line key. (This step not necessary if 
ringing line preference is assigned and is...

Basic Operation 
ABANDON HOLD DETECTION - If a distant party hangs up and 
the host system provides disconnect supervision, the holding 
station will: 
l Drop line from hold condition 
l Turn off tine status indicator 
PLACING INTERCOM CALLS 
Voice Announcing 
l Lift handset. 
l Press ITCM. 
l Press station number memory key (in memory key 
field) for desired station. 
0 Voice announce message. 
l Wait for reply or hang up. 
Tone Ringing 
l While on hook, press ITCM. 
l Press station number memory key...

Basic Operation 
CONFERENCE CALLS 
Multiline Conference for 2 external parties and 1 internal party 
NOTE: Conference transmission levels are not com- 
pensated and connections of parties must be super- 
vised by one inside party. 
l Establish first outside call and press HOLD. 
l Establish second outside call. 
l Press and hold down line key for second call. 
l Press line key for first call. 
l Release both line keys. Conference is established. 
To selectively disconnect one member of the 
conference,...

Feature Operation 
FEATURE OPERATION 
LINE MONITORING 
! 
Handsfree dial a number, 
l Press line key. 
l Dial number. 
l Monitor call ringing. 
l Lift handset when party answers. 
To activate line monitoring while on a call, 
l Press MONITOR. 
. Hang up handset. 
NOTE: Useful when a pafly 
places you on hold. You 
can monitor until caller’s return, then lift handset to 
resume con versa tion. 
To cancel monitoring, 
l Lift handset to resume conversation. 
-OR- 
. Press MONITOR to disconnect. 
AUTOMATIC...

Feature Operation 
line preference is busy or unavailable, press a line key 
and make the auto dial selection again. 
To program numbers, 
Press ITCM. 
Press SAVE. Listen for tone. 
Press desired key (in memory key field) for 
autodial ltc&ons l-20 (level 1). Tone will stop. 
s 
Press HOLD key, then memory key for auto dial 
locations 21-40 (level 2). 
If specific line is to be used, press that line key. 
Dial number sequence to be stored (up to 32 
digits). 
l Press dial pad to store digits 1-9, 0, #,...

Feature Operation 
REDIALING 
Saved Number Redial 
lhe last number dialed can be saved for redial 
at anytime. 
To save number, 
0 Press SAVE, during or after the call. 
To dial saved number, 
l Press HOLD key. 
l Press SAVE key. 
When party answers, 
l Lift handset. 
To cancel, 
l Press MONITOR. 
Last Number Redial 
The last number previously dialed can be 
redialed automatically stored to replace a pre- 
viously stored number. A special key is 
provided for the last number. 
NOTE: If the RED/AL key...