Cisco D9854i Manual

 
 
 Assigning a Program Channel to a PE (Program Entry) 
 
78-4021470-01 Rev J 7 
 
Assigning a Program Channel to a PE (Program 
Entry) 
 
1 At the start-up screen, PE1 is initially displayed. 
2 Press ADV and use the  keys to scroll through the available program entries. 
3 Press ADV again to select the channel number. 
4 Use the  keys to scroll through the available program channels or directly 
enter the channel number using the 0 to 9 keys; press SELECT to save the 
channel selection. 
Important:...

 
Chapter 1    Quick Setup - Read Me First!  
 
 
8 78-4021470-01 Rev J 
ASI Out 
1 Press MENU to move to the MAIN MENU.   
2 Press to move to the Setup menu. Press SELECT.   
3 Press to move to the Outputs menu. Press SELECT.   
4 Press to move to the TS Out menu. Press SELECT.   
5 Press SELECT to access the ASI menu. Press . Press SELECT. Use  to select 
the output mode. The factory default is No Output. It is recommended to set 
the Output Mode to MAP Svc Chans Only. Refer to Factory Default...

 
 
 Setting up the HD-SDI Outputs (SDI Model, with SD/HD-SDI and AES outputs) 
 
78-4021470-01 Rev J 9 
 
Setting up the HD-SDI Outputs (SDI Model, with 
SD/HD-SDI and AES outputs) 
The following displays the rear panel of the D9854 SDI Model, with SD/HD-SDI and 
AES outputs: 
 
1 Press MENU. 
2 Press  to move to the Setup menu. Press SELECT.  
3 Press  three times to move to the Services menu. Press SELECT.  
4 Press SELECT to enter the Video menu.  
5 Press SELECT to enter the PV Format menu, then use...

 
Chapter 1    Quick Setup - Read Me First!  
 
 
10 78-4021470-01 Rev J 
Setting up the MOIP Outputs (Base Model) 
The following displays the rear panel of the D9854 Base Model: 
 
1 Press MENU to move to the Main Menu.  
2 Press  to move to the Setup menu. Press SELECT.  
3 Press  to move to the Outputs menu. Press SELECT.  
4 Press  to move to the TS Out menu. Press SELECT.  
5 Press  to move to the MOIP menu. Press SELECT. Press . Press SELECT for 
Rate Control. Use   to select “USER”. Selecting...

 
 
 Setting the DPM Mode 
 
78-4021470-01 Rev J 11 
 
Setting the DPM Mode 
A program can be set to one of three Digital Program Mapping (DPM) modes, either 
Drop, Pass or Map respectively. For more information, see TS Out - DPM (on page 
103). 
LCD Setting Description 
Drop Removes the service and its associated PMT reference 
from the transport output.  
Pass Permits the source content and PMT reference to appear 
in the transport output with the same references unless 
the source material is mapped...

 
 
78-4021470-01 Rev J 13 
 
Overview 
This chapter is a general introduction to the D9854 Advanced Program 
Receiver. It describes the most common applications and interfaces of 
the receiver.  
 
 
2 Chapter 2 
Introduction 
In This Chapter 
 D9854 Advanced Program Receiver .................................................. 14 
 DVB-ASI Transport Stream Outputs ................................................. 17  

 
Chapter 2    Introduction  
 
 
14 78-4021470-01 Rev J 
D9854 Advanced Program Receiver 
The D9854 Advanced Program Receiver is designed for satellite content distribution 
applications requiring DVB-S and DVB-S2 reception capabilities with advanced 
digital outputs for digital tier program distribution. A built-in decoder will be 
capable of decoding a MPEG-2 or MPEG-4 High Definition (HD) program for analog 
monitoring or high-quality HD-SDI output version will be available for re-encode...

 
 
 D9854 Advanced Program Receiver 
 
78-4021470-01 Rev J 15 
 
 Uplink addressable decoder output control (VBI, audio routing, DPI, and ASI 
output) 
 Fingerprint trigger  
 Field upgradeable software and security  
 SNMP for setup, control, and monitoring 
 Front panel LCD for control and monitoring each with the ability to use part of 
their output for applications such as SAP, cue tones, etc. 
 DVB-VBI and SCTE-127 support 
 DTMF cue tone and cue trigger outputs for ad-insertion 
 Digital...

 
Chapter 2    Introduction  
 
 
16 78-4021470-01 Rev J 
SFN Model Receivers 
The Single Frequency Network (SFN) receivers do not include some of the key 
features normally equipped on D9854 receivers, such as Digital Program Mapping 
(DPM), MPEGoIP output, and transport stream null packet stuffing. These features 
are disabled on this receiver model. SFN model receivers can be identified by the 
part number “401943801060305” on the label on the top cover of the unit.  
Software Update 
All software in...