Cisco 881w Manual

 
2-21
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Items Shipped with your Router
Unpack the box and verify that all items listed on the invoice were shipped with the Cisco 819 ISR.
The following items are shipped with your router:
AC power supply (default)
AC power supply cable (default)
Cisco Configuration Professional (Cisco CP) CD
DC power supply (optional)
Power cord retention lock (available in Cisco 819HGW,...

 
2-22
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Ethernet Devices
Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. 
Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.
If you plan to configure the software using Cisco IOS commands through the console port, provide an 
ASCII terminal or a PC that is running terminal...

 
2-23
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
WarningRead the wall-mounting instructions carefully before beginning installation. Failure to use the 
correct hardware or to follow the correct procedures could result in a hazardous situation to people 
and damage to the system. Statement 378
WarningDo not cover or obstruct the router vents located on both sides of the router; otherwise, overheating 
could occur and...

 
2-24
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-18 Accessing the SIM Cards
Step 4
To open the SIM socket cover, slide the cover in the direction of the open arrow. (See Figure 2-19.) 
Figure 2-19 Opening the SIM Socket Cover
Step 5
Gently lift the cover on its hinges. (See Figure 2-20.)
245829
364622 

 
2-25
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-20 Lifting the Socket Cover
Step 6
Slide the SIM card into the slot in the cover. Gently push down the cover to close. The SIM card will 
come in contact with the metal contacts in the socket. (See Figure 2-21.)
364623 

 
2-26
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-21 Sliding the SIM Card into the Slot
Step 7
To lock the cover, slide it in the direction of the lock arrow. (See Figure 2-22.)
364624 

 
2-27
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-22 Locking the SIM Socket Cover
Step 8
Replace the panel and the screws.
Installing Antennas
NoteBefore you install the Cisco 819 ISR on a table, wall, or DIN rail, install the antennas on the front panel. 
It is difficult to install the antennas after the router is installed.
To attach the radio antennas to your wireless router, follow these steps:
Step...

 
2-28
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Installing a WiFi External Antenna
This section describes how to install a WiFi external antenna.
Step 1Install the lightning arrestor. For details in installing lightning arrestor, see Cisco Aironet Lightning 
Arrestor (AIR-ACC245LA-R). The lightning arrestor for cellular(3G/4G/LTE) is CGR-LA-NM-NF or 
CGR-LA-NF-NF. For detailed antenna information, see Ta b l e 1 - 1...

 
2-29
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Installing on a Table
To install the router on a table or other flat horizontal surface, firmly place the router on a table or other 
horizontal surface. Keep at least 1 inch (2.5 centimeters) of clear space for heat dissipation.
Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the 
“Installing the Router Using the...

 
2-30
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
NoteThe mounting brackets (PID number ACS-810-FWM) are not included in the package of C819G series 
routers.
Figure 2-26 Installing the Router to the Wall
NoteFor hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and 
washers must be size number 10.
Step 4Route the cables so that they do not put a strain on the connectors or...