Cisco 881w Manual

CH A P T E R
 
2-1
Cisco Integrated Services Router Hardware Installation Guide
 
2
Installing the Router
This chapter describes the equipment and the procedures for successfully installing the Cisco 860, 880, 
890 ISRs, Cisco 819 ISRs, and the Cisco 812 ISRs, and contains the following sections:
Installing the Cisco 810 ISR, page 2-1
Installing the Cisco 860, 880, 890 ISR, page 2-43
Installing the Cisco 810 ISR
This section contains the following:
Installing the Cisco 812 ISR, page 2-1
Installing the...

 
2-2
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Items Shipped with your Router
Unpack the box and verify that all items listed on the invoice were shipped with the Cisco 812 ISR.
The following items are shipped with your router:
AC power adapter 
Accessory kit 53-3453-01 which contains the following:
–Pointer document 78-19961-01
–RCSI document 78-17665-05
Mounting bracket kit C810-BR-CM
–Includes screws needed for...

 
2-3
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-1 10-24 Screws
Step 2
Install the PoE+ splitter into the mounting plate with four 6-32 screws. (See Figure 2-2.)
285667
1
1
3
2
110-24 screws
2Box hanger 
3Shelf bracket (PID 700-39491-01) 

 
2-4
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-2 6-32 Screws
Step 3
Connect the supplied plenum rated Cat5 cable to the GE0 port on the PoE+ splitter.   
Step 4Connect the Cat5 cable from your PoE+ source to the PoE+ in port on the PoE+ splitter.
Step 5Place the power cord lock onto the power cord behind the connector overmold as shown in Figure 2-3. 
Slide the power cord lock forward so that it captures...

 
2-5
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Step 6Install the power cord with power cord lock to the power jack of the PoE+ splitter while making sure 
that the two arms of the power cord lock slide into the corresponding slots on the PoE+ splitter and are 
fully seated with both arms locking into the slots. Figure 2-4 shows the installation of the power cord 
lock and other cables.
In the event that the power...

 
2-6
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-5 T-Rail
Installing the SIM Card
This section describes how to install and replace the SIM card. Ensure that the router is not mounted to 
a wall, rack, or DIN rail.
CautionDo not touch any part of the exposed PCB circuit area when the SIM cover is removed.
WarningHot surface. Statement 1079
To install the SIM card, perform these steps:
Step 1Power off the...

 
2-7
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-6 Accessing the SIM Card
Step 4
Remove the SIM card and install the new cards.
Step 5Reinstall the same 6-32 flat head screws using a screw driver to secure the access panel back in place. 
Figure 2-7 shows the SIM card installed and the SIM access panel closed.
344397 

 
2-8
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-7 SIM Access Panel
Installing the 3G Antenna
NoteInstall the antenna before you mount the Cisco 812 ISR. 
WarningDo not locate the antenna near overhead power lines or other electric light or power circuits, or 
where it can come into contact with such circuits. When installing the antenna, take extreme care 
not to come into contact with such circuits, because...

 
2-9
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Figure 2-8 Installing the 3G Antenna
Step 2
Orient the antenna perpendicular with respect to the floor. Figure 2-9 shows the 3G antenna installed.
Figure 2-9 3G Antenna Installed
Mounting the Cisco 812 ISR
This section describes the steps in mounting the Cisco 812 ISR in several configurations, including on 
a suspended ceiling, on a hard ceiling or wall, and on an...

 
2-10
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 810 ISR
Mounting Bracket, page 2-10
Ceiling Grip Clips, page 2-11
Mounting the Cisco 812 ISR Below a Suspended Ceiling, page 2-13
Mounting the Cisco 812 ISR on a Hard Ceiling or a Wall, page 2-15
Mounting the Cisco 812 ISR to a Network or Electrical Box, page 2-17
Grounding the Cisco 812 ISR, page 2-18
Mounting Hardware
Mounting hardware for the Cisco 812 ISR consists of...