Cisco 881w Manual

 
2-61
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 860, 880, 890 ISR
Figure 50 SIM Card Installation
282316
12
3
AB
4
AB 

 
2-62
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 2      Installing the Router
  Installing the Cisco 860, 880, 890 ISR
To install the SIM cards, follow these steps:
Step 1Open the door covering the SIM card slots.
a.Insert the tip of the screw driver into the upper latch and gently disengage it as shown in the figure.
b.Remove the door as shown.
Step 2To insert a SIM card into the SIM 0 slot, hold the SIM card with the contacts facing up as shown and 
gently push the card...

CH A P T E R
 
3-1
Cisco Integrated Services Router Hardware Installation Guide
 
3
Connecting the Router
This chapter describes how to install the Cisco 860, 880, 890 ISRs and the Cisco 819 ISR.
Cisco 810 Series, page 3-1
Cisco 860, 880, 890 Series, page 3-8
Cisco 810 Series
Cisco 819 Series
This section describes how to connect Cisco 819 ISRs to Ethernet devices and a network. The section 
contains the following topics:
Preparing to Connect the Router, page 3-1
Connecting a PC, Server, or Workstation,...

 
3-2
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 3      Connecting the Router
  Cisco 810 Series
Preventing Damage to the Router
To prevent damage to your router, follow these guidelines when connecting devices to your router:
Turn off power to the devices and to the router until all connections are completed.
CautionDo not turn on the devices until after you have completed all connections to the router.
If you must supply your own cable, see the “Cisco 860, 880, 890 Series”...

 
3-3
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 3      Connecting the Router
  Cisco 810 Series
Step 3(Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.
NoteUse the Cisco Configuration Express to configure the Internet connection settings. See 
Cisco Configuration Professional Quick Start Guide for more information.
Connecting an External Ethernet Switch 
If more than four PCs in an office must be connected to each other, you can...

 
3-4
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 3      Connecting the Router
  Cisco 810 Series
Connecting a Terminal or PC to the Console Port
Connect a terminal or PC to the Console port either to configure the software by using the CLI or to 
troubleshoot problems with the router. 
To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:
Step 1Connect the RJ-45 end of a DB-9-to-RJ-45 serial cable to the RJ-45 Console port on the...

 
3-5
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 3      Connecting the Router
  Cisco 810 Series
Connecting a Modem to the Console Port
To connect a modem to the router, follow these steps:
Step 1Connect the RJ-45 end of the adapter cable to the Console port on the router as shown in Figure 3-4. 
Figure 3-4 Connecting a Modem to the Console Port
Step 2
Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter. 
Step 3Connect the DB-25 end of the modem...

 
3-6
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 3      Connecting the Router
  Cisco 810 Series
To connect your Cisco 819 ISR to an AC power outlet, follow these steps:
Step 1Connect the AC adapter to an AC power outlet.
Step 2Plug the adapter cord into the router.
Connecting the DC Adapter
WarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that 
the protective device is rated not greater than 36 VDC, 5A Statement...

 
3-7
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 3      Connecting the Router
  Cisco 810 Series
Figure 3-6 DC Power Supply PWR2-20W-12VDC and PWR2-20W-24VDC
Step 2
Plug the adapter cord into the router.
NoteThe power adapters have 18 AWG wires for the input connection. Tinned bare wires are used for 
the input connection as there is no standard established for connector type. Screw terminal 
blocks are most often used.
Verifying Connections
To verify that all devices are...

 
3-8
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 3      Connecting the Router
  Cisco 860, 880, 890 Series
Cisco 860, 880, 890 Series
This section describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs to 
Ethernet devices, Power over Ethernet (PoE), and a network.
NoteDepending on the features available for your router, some content in this section may not apply to your 
router.
The section contains the following topics:
Safety Warnings, page...