Cine Versum Cineversum Projector Lv Wu6k User Manual

40
 2/2
MENUSELECT
1/2
MENUSELECT
menu
Setting
On start
Standby mode
Closed caption
Lamp control
Test pattern
High   land Cooling fast
Filter   counter
Warning log
Factory defaultOff
Move
ExitNext
Language
OSD setting
Auto setup
Keystone
Blue Back
Display
Logo
Ceiling
Rear
Terminal
Power  management English
Move Exit
Next
menu
Setting
Setting
Setting
You can use the setting menu to configure the
following functions.
1.Press F. Menu on the remote control to display the
on-screen menu. Press

·ito select...

41
Blue back
You can use this item to set the background of
The time when no signal is detected.
You can press
x
zto switch over between the
items below:
ON: To enable the blue background for
projection;
OFF: To disable the blue background.
Setting
Auto setup
Input search
This function detects the input signal automatically. When 
a signal is found, the search will stop. Use the Point 
x
z
buttons to select one of the following options.
Off ...........  Input search will not work.
On........... .. Active...

42
Setting
Logo (Logo and Logo PIN code lock settings)
This function allows you to customize the screen logo with Logo select, Capture, Logo PIN code lock
and Logo PIN code change functions.
3NOTE:
When On is selected in the Logo PIN code lock function, Logo select and Capture functions cannot be 
  selected.
Logo select
This function decides on the starting-up display
from among following options.
User ........ Show the image you captured.
Default .... Show the factory-set logo.
Off ........... Show the...

43
Setting
Logo PIN code lock
Use the Point
x
zbuttons to enter a number. Press the Point
ybutton to fix the number and move the red
frame pointer to the next box. The number changes to “*”. If you fixed an incorrect number, use the Point
{
button to move the pointer to the number you want to correct, and then enter the correct number.
Repeat this step to complete entering a three-digit number.
After entering the three-digit number, move the pointer to Set. Press the SELECT button so that you can start...

44
Setting
Rear
When this function is set to On, the picture will be left/right 
reversed. This function is used to project the image from 
rear of the screen.
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer input or 
monitor output. (See page 9) Select Computer or Monitor Out with the Point 
x
z buttons.
PC 2................. ...Computer 2 Inputomputer 2 Input
Monitor Out........Monitor Output
Power management
Time left before Lamp is off.
Power...

45
Setting
Auto............Brightness is adjusted according to the input signal.
Standby mode
This function is available when operating the projector via network.
  Normal ...... Supply the power to the network function even after turning off the projector. You can turn on/ off
                      the projector via network, modify network environment, and receive an e-mail about projector 
                      status while the projector is powered off.
  Eco ...........  Select Eco when you do not use...

46
Setting
PIN code lock
This function prevents the projector from being operated by unauthorized persons and provides the following 
setting options for security.
Off ............ Unlocked.
On ........... Enter the PIN code every time turning on the projector.
Whenever you change the PIN code lock setting or the PIN code (the three-digit number), you are required to 
enter the PIN code. The “111” is set as the initial PIN code at the factory.
If you want to change the PIN code lock setting, Press the...

47
Setting
ON (1)........The fan runs faster than normal speed. Whenoperated in places with high altitude
(2000m), the cooling fan will produce weaker effects. So, you should select this item.
ON (2)........The fan runs faster than “ON (1)”. When operated in places with high altitude
(above 3000m), the cooling fan will produce weaker effects. So, you should select this item.
There are the following options in the cooling fans operation when the projector is turned off.
 ON ... Faster and louder-sound...

48
                               KH
                               H
MENUSELECT
z
z1080i
A
Information
Displaying input source
The information menu is used to detect signal of projected image and running state 
Operation through menu
Press
x
zto select the information. And the information menu will appear.
You can then see the information displayed as follows:
Information
Input
H-sync freq.
V- s y n c f r e q .
Screen
Language
Lamp status
Power management
Key lock
Back
ExitMove
Component...

49
“Warning Temper” indicator
The “Warning Temper” indicator tells in what pr otection stateengaged. The user should
check the “Warning Temper” indicator and power indicator to make sure they work.
Projector is in OFF state, and “Warning Temper” indicator flashes red.
When its internal temperature exceeds the normal value,
will be automatically powered off to protectthe parts.
Whenin a cooled state, the power
indicator will blink.
When it is cooled enough (restore
the normal operating
temperature), you...