Cine Versum Cineversum Projector Lv Wu6k User Manual

							40
 2/2
MENUSELECT
1/2
MENUSELECT
menu
Setting
On start
Standby mode
Closed caption
Lamp control
Test pattern
High   land Cooling fast
Filter   counter
Warning log
Factory defaultOff
Move
ExitNext
Language
OSD setting
Auto setup
Keystone
Blue Back
Display
Logo
Ceiling
Rear
Terminal
Power  management English
Move Exit
Next
menu
Setting
Setting
Setting
You can use the setting menu to configure the
following functions.
1.Press F. Menu on the remote control to display the
on-screen menu. Press

·ito select Setting.
Then press

yor press Select to enter the
submenu.
2.Press
·ito select the desired item to be
adjusted, and then press

yor press Select to
reach the selected item.
3.Press
·ito select the desired item and then
press Select.
OSD language
OSD languages include English,Chinese, French,
Spanish, Portugal, German, Italian, Japanese, Korean,
Russian, Finnish, Dutch, Thai, Vientnamese, Turkish,
Afrikaans, Bahasa Indonesia, Arabic.
OSD setting
Press
·ito select OSD setting. then press Select or

y
.
Menu posi tion:
You can use this function to changethe
positionof
on-screen menu. To do that, select menu position
and press Select. Each time you press Select,
the menu’s position on the screen in the order
below:
Upper left
:Upper right
:Center
:Lower left
:
Lower right
:Upper left
:…
Translucent
This item allows you to change the transparency of
the on-screen menu. Press
x
zto select from these
options: Off, High, Mid  and Low.
Background
This item allows you to change the background of the
on-screen menu. Press
x
zto select from options
0-6.
Security
Off Off Off
Eco Off Store
On
On
Auto
Off
Monitor out
Back
Back 
						

							41
Blue back
You can use this item to set the background of
The time when no signal is detected.
You can press
x
zto switch over between the
items below:
ON: To enable the blue background for
projection;
OFF: To disable the blue background.
Setting
Auto setup
Input search
This function detects the input signal automatically. When 
a signal is found, the search will stop. Use the Point 
x
z
buttons to select one of the following options.
Off ...........  Input search will not work.
On........... .. Active Input Sourcing fuction. It detects the 
input signal and search stops when the signal is 
found.
Auto PC Adjustment
On........... .. Press Auto Set button on the Top Control or 
remote control to enable Auto PC Adjustment
function.
Off ...........  Disables Auto PC Adjustment. This function enables Input search,
 by pressing theand Auto PC adjustment
AUTO SETUP button  on the top control or the
AUTO SET button on the remote 
can be altered as follocontrol. Settings for those
ws:
Keystone Correction
This function is used to store or reset the keystone 
correction when the AC power cord is unplugged. Use the 
Point
x
z buttons to switch between each option.
Store ...... ...... Keep the keystone correction even when
                          the AC power cord is unplugged.
Reset ............ Release the keystone correction when the
AC power cord is unplugged.
To correct keystone distortion, press the SELECT button. 
Keystone appears on the screen. Use the Point 
x
z
buttons to correct keystone distortion.3NOTE:
‡Only the last selected input source can be 
detected.
‡If the INPUT button on the top control or 
the COMPUTER 1/2 buttons, VIDEO or 
S-video or COMPONENT buttons on the 
remote control is pressed during Input 
search is in progress, Input search will stop 
and go back to the previous input signal.
‡Input Search,Auto PC Adj. can not 
be set Off
 at the  same time.
‡Fine sync.,Total dots,Horizontal and 
Vertical position of some computers 
cannot be fully adjusted with the Auto PC 
Adjustment function. When the image is 
not provided properly with this operation, 
manual adjustments are required. 
						

							42
Setting
Logo (Logo and Logo PIN code lock settings)
This function allows you to customize the screen logo with Logo select, Capture, Logo PIN code lock
and Logo PIN code change functions.
3NOTE:
When On is selected in the Logo PIN code lock function, Logo select and Capture functions cannot be 
  selected.
Logo select
This function decides on the starting-up display
from among following options.
User ........ Show the image you captured.
Default .... Show the factory-set logo.
Off ........... Show the countdown display only.
Capture
This function enables you to capture an image being projected to use it for a starting-up display or interval of 
presentations.
SelectCapture and press the SELECT button. A confirmation box appears and select Ye s to capture the 
projected image.
After capturing the projected image, go to the Logo select function and set it to User. Then the captured image 
will be displayed the next time you turn on the projector.
This function prevents an unauthorized person from changing the screen logo.
Off ...... ..... The screen logo can be changed freely from the Logo Menu.
On ........... The screen logo cannot be changed without a Logo PIN code.
If you want to change the Logo PIN code lock setting, press the SELECT button and the Logo PIN code 
dialog box appears. Enter a Logo PIN code by following the steps below.
Logo PIN code lock On............................
Show startup screen
Off ............................Show the input image instead of the on-start screen
Display
You can use this item to set whether the startup animation is displayed. 
						

							43
Setting
Logo PIN code lock
Use the Point
x
zbuttons to enter a number. Press the Point
ybutton to fix the number and move the red
frame pointer to the next box. The number changes to “*”. If you fixed an incorrect number, use the Point
{
button to move the pointer to the number you want to correct, and then enter the correct number.
Repeat this step to complete entering a three-digit number.
After entering the three-digit number, move the pointer to Set. Press the SELECT button so that you can start 
to operate the projector.
If you entered an incorrect Logo PIN code, Logo PIN code and the number (***) will turn red for a moment. 
Enter the correct Logo PIN code all over again.
Logo PIN code can be changed to your desired three-
digit number. Press the SELECT button to select Logo
PIN code change.Logo Pin code dialog box appears, 
use the Point 
x
z buttons to enter the correct code. The
New Logo PIN code input dialog box appears. Set a new
Logo PIN code, confirmation box appears, choose yes to 
set the new Logo Pin code.
Be sure to note the new Logo PIN code and keep it on 
hand. If you lost the number, you could no longer change 
the Logo PIN code setting.
Use the Point 
x
z buttons to switch No or yes, and then 
press the SELECT button to make a choice. Change the Logo PIN code lock setting
CAUTION:
WHEN YOU HAVE CHANGED THE LOGO PIN CODE,
WRITE DOWN THE NEW PIN CODE IN COLUMN OF 
THE LOGO PIN CODE NO. MEMO ON PAGE 59, AND
KEEP IT SECURELY. SHOULD THE LOGO PIN CODE
BE LOST OR FORGOTTEN, THE LOGO PIN CODE
SETTING CAN NO LONGER BE CHANGED.
Logo PIN code change 
						

							44
Setting
Rear
When this function is set to On, the picture will be left/right 
reversed. This function is used to project the image from 
rear of the screen.
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer input or 
monitor output. (See page 9) Select Computer or Monitor Out with the Point 
x
z buttons.
PC 2................. ...Computer 2 Inputomputer 2 Input
Monitor Out........Monitor Output
Power management
Time left before Lamp is off.
Power management
For reducing power consumption as well as maintaining the lamp life, the Power management function turns off
the projection lamp when the projector is not operated for a certain period.
Select one of the following options:
Ready .................. When the lamp has been fully cooled down, the POWER indicator changes to green blinking. 
In this condition, the projection lamp will be turned on if the input signal is reconnected or any 
button on the top control or remote control is pressed. 
Shut down ..........  When  the  lamp  has  been  fully  cooled down, the power will be turned off.
Off ....................... Power management function is off.
Timer ................... If the input signal is interrupted and no button is pressed for more than 30 seconds, the timer 
display with No signal appears. It starts the countdown until the lamp is turned off. Use the 
Point
x
z buttons to set the Timer(1~30min.).
3NOTE:
  Factory default is Ready: 5 Min.
On start
This function enables projector auto power on with detection connection with AC power cord. Ceiling
This function is used to project the image from a ceiling-
mounted projector.
Off ......Disable this function.
Auto ........The picuture will be top/bottom and left/right 
reversed automatically.
On..........The picture will be top/bottom and left/right 
reversed.
Rear
    No signal
01 : 20 
						

							45
Setting
Auto............Brightness is adjusted according to the input signal.
Standby mode
This function is available when operating the projector via network.
  Normal ...... Supply the power to the network function even after turning off the projector. You can turn on/ off
                      the projector via network, modify network environment, and receive an e-mail about projector 
                      status while the projector is powered off.
  Eco ...........  Select Eco when you do not use the projector via network. The projector’s network function will 
                      stop when turning off the projector.
Closed Caption
Closed Caption is a text version of the program sound or other information displayed on the screen.If the input 
signal contains closed captions, you can turn on the feature and switch the channels. Press the Point 
x
z
buttons to select Off, CC1, CC2, CC3 or CC4.
If the closed caption is not clear, you can change the text from Color to white.
3
NOTE:
The Closed Caption is available only under the situation below.
QGWKHV\VWHPLVVHWDFFRUGLQJWRWKHVLJQDORU
      set on Auto.
‡The system must be set on NTSC or Auto in Video System Selection. (P.36)
‡The icon of Closed Caption is displayed in gray while it is not available.
‡The Closed caption is unavailable when On-Screen menu and Timer are displayed.
This function allows you to change brightness of the screen.
Normal ...... Normal brightness
Eco ............Lower brightness reduces the lamp power consumption and extends the lamp life.
Lamp Control 
Key lock
Security (Key lock and PIN code lock)
This function locks the top control and remote control buttons to prevent operation by unauthorized persons. 
SelectKey lock and then press the SELECT button, and select the desired item by pressing the Point 
x
z
buttons.
Off .................. Unlocked.
Projector ........ Lock the operation of the top control. To unlock, use the remote control.
Remote Control  ..... Lock the operation of the remote control. To unlock, use the top control.
If the top control accidentally becomes locked and you do not have the remote control nearby or there is 
something wrong with your remote control, contact the dealer where you purchased the projector or the 
service center.
This function allows you to use the Key lock and PIN code lock function to set the security for the projector 
operation.
This function enables you to test & set interior signals.
Test Pattern 
						

							46
Setting
PIN code lock
This function prevents the projector from being operated by unauthorized persons and provides the following 
setting options for security.
Off ............ Unlocked.
On ........... Enter the PIN code every time turning on the projector.
Whenever you change the PIN code lock setting or the PIN code (the three-digit number), you are required to 
enter the PIN code. The “111” is set as the initial PIN code at the factory.
If you want to change the PIN code lock setting, Press the SELECT button and the PIN code dialog box 
appears.
Enter a PIN code
Use the Point
x
zbuttons to enter a number. Press the Point
ybutton to fix the number and move the red 
y
frame pointer to the next box. The number changes to “*”. If you fixed an incorrect number, use the Point
{
{
button to move the pointer to the number you want to correct, and then enter the correct number.
Repeat this step to complete entering a three-digit number.
After entering the three-digit number, move the pointer to “Set.” Press the SELECT button so that you can 
start to operate the projector.
If you entered an incorrect PIN code, PIN code and the number (***) will turn red for a moment. Enter the 
correct PIN code all over again.
Use the Point 
x
z buttons to select Yes or No,and t
hen press the SELECT button to make a choice.
Change the PIN code lock setting
The PIN code can be changed to your desired three-digit number. Press 
x
z SELECT button to select PIN 
code change. Pin code dialog box appears, use the Point
x
z buttons to enter the correct code. The New 
PIN code input dialog box appears. Set a new PIN code.
CAUTION:
WHEN YOU HAVE CHANGED THE PIN CODE, WRITE DOWN THE NEW  PIN CODE IN COLUMN OF 
THE PIN CODE NO. MEMO ON PAGE 59, AND KEEP IT SECURELY. IF YOU FORGET YOUR PIN CODE, 
THE PROJECTOR CAN NO LONGER BE STARTED.
PIN code change 
						

							47
Setting
ON (1)........The fan runs faster than normal speed. Whenoperated in places with high altitude
(2000m), the cooling fan will produce weaker effects. So, you should select this item.
ON (2)........The fan runs faster than “ON (1)”. When operated in places with high altitude
(above 3000m), the cooling fan will produce weaker effects. So, you should select this item.
There are the following options in the cooling fans operation when the projector is turned off.
 ON ... Faster and louder-sound than the normal operation, but it takes less time to cool the projector down.
 OFF ... Normal operation. Cooling fast
This projector provides Fan control function in the "Setting" menu. Choose the running speed of cooling fans 
from the following options according to the ground elevation where you use the projector.
Off......Normal speed.Set this function to "Off" when using the projector in non-high altitude environment.
High land
This function is used to set a frequency for the filter cleaning.
When the projector reached a specified time between cleanings, a Filter warning icon appears on the screen, 
notifying the cleaning is necessary. After cleaning the filter, be sure to select RESET and set the timer. The Filter 
warning icon will not turn off until the filter counter is reset. Filter counter
Factory default
This function returns all setting values except for the User
logo,PIN code lock,Logo PIN code lock,
Lamp counter
andFilter counter
 to the factory default settings. 
						

							48
                               KH
                               H
MENUSELECT
z
z1080i
A
Information
Displaying input source
The information menu is used to detect signal of projected image and running state 
Operation through menu
Press
x
zto select the information. And the information menu will appear.
You can then see the information displayed as follows:
Information
Input
H-sync freq.
V- s y n c f r e q .
Screen
Language
Lamp status
Power management
Key lock
Back
ExitMove
Component
                            Normal
English
10 H
  Off
1min
Lamp counter
H-sync freq .
V-sync freq .
Lamp counter The horizontal frequency of the input signal is displayed in
KHz, or - - - -KHz when no signal.
The vertical frequency of the input signal is displayed in Hz,
or - - - - Hz when no signal. Numbers of Hz doubles when
during Interlace.
The cumulative lamp operating time is displayed.Press menu on the Top Control and then press SELECT
button to display on screen menu. Press the Point 
x
z
buttons to select the Information. The Information Menu is
displayed.
See below for displayed information. Menu Operation
Input
LanguageThe selected input source is displayed.
The selected language is displayed.
Key lock
Display Off, Remote Control or the Projector. Power management Screen
The selected screen size is displayed.
Lamp status
The selected lamp mode is displayed.
Off, Ready or Shut down is displayed. 
						

							49
“Warning Temper” indicator
The “Warning Temper” indicator tells in what pr otection stateengaged. The user should
check the “Warning Temper” indicator and power indicator to make sure they work.
Projector is in OFF state, and “Warning Temper” indicator flashes red.
When its internal temperature exceeds the normal value,
will be automatically powered off to protectthe parts.
Whenin a cooled state, the power
indicator will blink.
When it is cooled enough (restore
the normal operating
temperature), you can
press thepower key tostart up
 the system.
¥Note:
When
restores
itsnormal operating
temperature, the
“Warning TEMP” indicator will flash continuously. If you
re-start the projector, it will stopflashing.
Check the items below:
-Whether the site whereinstalled is well
ventilated, and whether the vent is blocked.
-Whether installed near the vent of air
conditioner. Note it can not be installed at that place.
-Whether the filter is clean. You should clean it
regularly.
Projector is in OFF
state, and “Warning TEMP ”
indicator is
illuminated red.
When any abnormity
is detected, The projector 
will be automatically powered off to protect its internal
parts. At the time, the “Warning TEMP” indicator will
be illuminated red. In this case, you should unplug the
power cord and plug it again, then power on the
projector again for check. If the projector is still in OFF
state and “Warning TEMP” indicator is illuminated red,
you should unplug the power cord and contact the
repair center for maintenance.
Note:
When abnormity occurs, the user should cut
off the AC power. Otherwise, it may lead to
fire or electric shock. On-top control panel
“Warning TEMP” indicator is illuminated red.
Maintenance