Cine Versum Cineversum Projector Lv Wu6k User Manual

							50
Note:
Keep from dust and smog.
Otherwise, the image quality may deteriorate.
Whenoperated in an environment
with dust and smog, the dust and dirt will
accumulate on its lens, liquid crystal board or
the lens assembly inside the projector. If that
happens, you should contact the local
distributor or repair center for correct
cleaning.
Maintenance
Cleaning the filter
The filter prevents dust from accumulating on the surface of lens assembly.Should the
filter become clogged with dust particles, it willreduce the cooling fan’s effectiveness and may result
in inte
rnal heat buildup and adversely affect the life of the projector. If a Filer warning icon appears on
the screen, you should clean the filter immediately. To do that, follow the steps below: 
1. Turn off the projector, and unplug the AC power
cord from the outlet.
2. Remove the air filter from the projector.
3. Brush the filter clean.
4. Install the filter onto the projector again and make
sure it is secured properly.
Note:
Do not operate the projector when the
filter is removed. Other
wise, dust will be
accumulated on lens and thus affect the
image quality.
Never attempt to place any objects to the
air intake vents. Otherwise, the projector
may malfunction.Filter
Resetting the filter counter
1. Press F. Menu on the remote control to display the
F. Menu. Press
x
zto select the icon for the
setting menu. Then press
y or press Select.
2. Press
x
zto select Filter counter , and then press

yorpress Select. Press
x
zto select Reset Filter,
then press Select. At the time, you will see the
prompt information “Reset the filter counter ? ” displayed
on the screen. Select Yes.
3. W
hen another dialog box pops up, you should
select Yes and reset the filter. 
						

							51
Maintenance
Covering the lens properly
If needs to be moved or won’t be used for
extended period of time, you should cover the lens
properly.
Cleaning the lens
Unplug the AC power cord before cleaning.
Apply some non-abrasive cleaning agent exclusively
designed for cameras onto a piece of clean cloth, and then
use it to wipe the lens ge ntly. Or you can use cleaning
paper or commercial blower to clean the lens.
Avoid excessive use of cleaning agent. Abrasive cleaning
agent, solvent or other coarse chemicals may scratch the
lens.
Cleani
ng the projector’s shell
Unplug the AC power cord before cleaning.
Use a piece of clean cloth to gently wipe the surface of
projector. If the projector is quite polluted, you can apply
some neutral cleaning agent onto a piece of clean cloth,
and use it to wipe the shell. Avoid excessive use of
cleaning agent. Abrasive cleaning agent, solvent or other
coarse chemicals may scratch the lens.
When not used, you should put it into a bag to
avoid dust and scratch. 
						

							52
To replace the lamp, follow the steps below:
1. Power off the projector and unplug the power
cord. Then let the project cool for at least 45
minutes.
2. Loosen the screws on the lamp cover and open
the cover.
3. Make sure the lamp is well protected and
remove two screws. Hold the handle and pull
out the lamp.
4. Install a new lamp with the same model and
tighten the two screws. Make sure the
installation is correct. Put lamp cover in place
and then tighten the screws.
5. Plug the AC power cord and power on the
projector.ScrewHandle
LampScrew
Screw
Lamp
cover
Note:
When the lamp isn’t illuminated, it may indicate that the lamp has been damaged.
When you replace the lamp in a projector installed on the ceiling, you should stand beside the lamp
cover but not under it; for the broken glass may fall down to hurt you. To do that, remove the lamp
cover gently to avoid being hurt by the dropped glas s. If glass drops into your eyes or mouth, you
should see the doctor immediately.
Note:Note:
As temperature inside the projector is high, you
should cool the projector for at least 45 minutes
before you open the lamp cover.For the sake of safety, only use the lamp of the
same model. Never drop the lamp onto the ground
nor touch the glass bulb! The glass can shatter and
hurt.
Maintenance
Replacing the lamp
When the service life of the projection lamp is over, the
icon suggests that the lamp needed to be replaced will
appear on the screen, and the indicator for the
replacement will flash yellow. If so, you should
immediately replace it with a new one of the same model.
The flashing time of the replacement indicator is subject
to the lamp mode. 
						

							53

½Ö
Maintenance
Changing the lamp model
Purchasing new lamps
Users can buy new lamps through the local distributor. Your purchase order should include the
information below:
Lamp model
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.

”Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee 
of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time 
than other similar lamps.

”If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights 
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. 
    (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of   
    the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

”A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its 
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in 
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN .
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an 
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check 
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out 
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one 
should check the inside of the projector except those who are authorized trained technicians and who 
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those 
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken 
glass.
LAMP HANDLING PRECAUTIONS 
						

							54
Appendix
Troubleshooting
Before you contact the local distributor or repair center, you may check the items below once again.
-Make sure you have properly connected to the peripheral equipment.
-Make sure all equipment has been connected to AC power source and the power source is in ON state.
-If it can’t project image output from a PC, please re-start the PC.
n o i t u l o S
e r u l i a F
Machine can’t be powered on -Plug the power cord  of the projector into the AC power outlet.
-Check whether the power indicator turns red.
-Only when the power indicator turns red can you power on the
projector again.
-Check the Warning Temp indicator. If it is illuminated red, you can’t
power
-Check the projection lamp.
-Unlock the “key lock” function.
No initial displaying -Make sure both displa ying and count-down functions are enabled.
Initial displaying is inconsistent
with
factory defaults-Make sure the item User or OFF is not selected in the startup
animation.
Input signals are automatically switched
(can’t be switched)-Adjust the search function of  input source properly.
When input is pressed during startup, a
non-Lamp icon appears.-This icon warns that the filter needs to be replaced.
An icon of non-input mode or lamp mode
appears-This icon indicates the replacement of lamp or warns for the filter.
Ambiguous images -Adjust the focus
-Set a more proper projection distance.
-Check whether the lens needs to be cleaned.
-When moved from a environment with low temperature to
the one withhigher temperature, water will be condensed on the lens. If
so, you have to wait till the condensed water disappears.
Image turns over leftward/rightward
Image turns over upward/downward-Check the function of “ceiling/rear”.
-Check the function of “ceiling”.
Image not bright enough-Check whether the contrast or brightness is adjusted correctly.
-Check whether the image mode is properly selected.
-Check the function of lamp brightness adjusting.
-Check the lamp and replace the indicator. If the indicator isilluminated,
it means the service life of the lamp is over. You should replace the lamp
with a new one of the same model immediately. 
						

							55
Appendix
No image -Check the connection between PC or video equipment
-Check with the signal from PC is correct. If connected to
certain laptops, the settings of their video adapters need to be changed.
You can refer to the operating instructions of the PC for such
modification.
-Images can show up only about 20 seconds after the projector is
powered on.
-Check the input signal, color system, video system or PC system mode.
-Make sure that the temperature doesn’t exceedthe permitted oper
ating
temperature (41 F–95
F [5
C–35C]).
-If non-displaying function is enabled, no image will appear on the
screen. You can then press the non-display key or other keys.
No sound is heard. -Check that the audio cable from the input source is correctly connected.
-Adjust the audio source.
-Press the key “+”.
-Press the key “Mute”.
-If the audio cable is inserted into the port AUDIO OUT, the internal
speaker of the projector will be disconnected.
-Isthere any image projected? Only when the image appears on the
screen, can the sound be heard.
Abnormal color -Check the input signal, color system, video system or PC system mode.
-Make sure the green board is not selected in the item “image quality”.
Some information can’t be seen in the
operation.-Check the function of displaying.
Automatic adjustment through PC can’t
be effective.-Check the signal of input source. Automatic adjustment through PC
won’t be effective when 480p, 575p, 720p,
480i, 575i, 1035i or 1080i is selected.
Settings can’t be saved after the system is
powered off.-Make sure you have selected “store
store” after you changed the settings.
Some settings can’t be saved if “ ” is not selected.
Ineffective power control-When the system is standstill, or no-display function is enabled, the
power control is ineffective.
Ineffective icon selection-Check the wiring and the signal of input source, and make sure there is
signal.
Ineffective automatic setting-Make sure all functions in automaticsetting are enabled.
-Make sure the function of ceiling is not enabled. 
						

							56
Appendix
Distorted image or no image
-Check and adjust the PC menu or on-screen menu.
The PIN code dialog box popes up in the
startup
process-A PIN code is set for locking.
Remote control doesn’t work-Check the battery.
-Make sure there is no obstacle
between the projector and the remote control.
-To use the remote control, keep it within 5 meters away from the
projector.
-Make sure the code of the remote
control is consistent with the projector.
-Unlock the key through the setup menu.
The indicator is illuminated or flashes-Check the state of the projector according to the indicator.
Excalmatory point appears on the screen -Ineffectiveoperation. You should operate the system correctly.
The side control panel doesn’t work-Unlock the keys on the side control panel through the item
“security” in the setup menu.
PIN code lock for startup animation, key lock
and PIN code lock can’t be unlocked.-Contact the local distributo r or the repair center.
Warning:
s operated with high voltage. Do not open its casing!
II
f the problem still exists after you take the aforesaid measures, you should contact the local distributor or the repair
center and tell the machine model. wThe projector ill tell you how to handle the issue. 
						

							57
POWERWARNINGLAMPSHIFTFOCUS
?
?
green
red
yellowoff
green flashred flash
*When the projector bulbreaches its endurance, the indicator light will be yellow and you need to
change the bulb.
Appendix
Indicator and projector state
Check the indicator to know about the state of projector.
Indicator
(Green/red) (Red) (Yellow) (Blue)(Green)
State of projector
Is in power-off state (AC power cord not
inserted).
Is in standby state. Press ON/STNADBY to
power on the projector.
Is in normal working state.
Is ready to be in standby mode or the
projection lamp is being cooled. Before you power
on the projector, you should wait till the lamp is cool
enough and the power indicator flashes.
Is in suspension state.
Internal temperature too high. can’t be
powered on. When the projector is cool enough, the
temperature is restored to the normal value and the
power indicator is illuminated red, you can then
power on the projector (The indicator Warning Temp
keeps on flashing).
When the projector is cool enough, the temperature
is restored to the normal value and thepower
indicator is illuminated red, you can then power on
the projector, At the time, the indicator Warning
Temp stops flashing. 
Can’t be powered on because error is
detected. You should unplug the power cord. Then
insert it again and power on the projector. If the
projector is powered off again, you should cut off
the power and contact the local distributor or repair
center. In this case, stop the projector. Otherwise,
electric shock or fire may occur.
The service lifeof the lamp is over. You should
replace it with a new one in time.
Lens is moving and being adjusted.
Focus being adjusted.
blue 
						

							58
3
640x400 601152x900 65
640x400 701152x900 75
640x400 851280x1024 60
640x480 601280x1024 65
640x480 651280x1024 70
640x480 721280x1024 72
640x480 751280x1024 75
640x480 851280x1024 85
800x600 50WX
WUXGAGA 1280x768 60
800x600 601280x768 75
800x600 651280x768 85
800x600 721280x768 120
800x600 751360x768 60
800x600 851360x768 72
800x600 1201366x768 60
832x624 751280x800 60
XGA 1024x768 601280x800 75
1024x768 651280x800 85
1024x768 701280x800 120
1024x768 72
1
080psf241920x1080 1920x1200
24
1024x768 75
1
080psf251920x1080 25
1024x768 80
1
080psf301920x1080 30
1024x768 85
480i 60
1024x768 120
575i 50
1152x864 70
480p 60
60 1035i 60
575p 50
1080i 60
720p 50
1080i 50
720p60 SXGA
VGA
SVGA
Appendix
Compatible PCs
Is compatible with all analog and digital signal formats under 160MHz of DCLK, whose resolution and
correspondent field frequencies are listed below:
Note:
The specification is subject to change without prior notice.
Signal format Resolution Field frequency(HZ)Signal format Resolution Field frequency(HZ) 
						

							59
512341096781514131112
-----
1
5
2
4
3
6
7
8
-----9
13
10
12
11
14
15
RX –
TX +
TX –
RX +
2
3
4
87654321
5
6
7
8
1-----
-----
----------
-----
R X D
T X D
-----
GND
-----
1
2
3
4
5
6
7
8
-----9
-----
-----
PIN code memorandum
Write down the PIN code in the blank below and keep it,
please contact the repair center.
PIN code lock
*If this 3-digit number is changed,
the factory
default number will be ineffective. Factory default PIN code 111*
Factory default PIN code 111*
Locking startup-animation PIN code
Appendix
Configuration of terminals
OMPUTER IN 1/COMPUTER IN 2/MONITOR OUT (analog)
Terminal: Analog RGB (D-sub 15-pin)
CONTROL PORT terminal (D-SUB-9-Pin)          LAN terminal
Red   (Input/output)
Green (Input/output)Grounding (field synchronizing)
Blue (Input/output)Grounding
DDC data
Grounding (line synchronizing)Horizontal synchronizing
(compound sync.) input/output
Grounding (red)Vertical synchronizing
input/output
Grounding (green)
DDC clock
Grounding (blue)