Cine Versum Cineversum Blackwing User Manual

 
3.0  INSTALLATION  
R599727 - BlackWing User Manual11  
Precautions for Ceiling-mount 
•To ceiling-mount this unit, special expertise and techniques are necessary.
Be sure to ask your dealer or specialist to perform mounting.
•Do not mount at places that may be subjected to vibration and shock.
•Depth of the screw holes (screw length) is 30 mm. Use screws shorter than
30 mm but longer than 19 mm. Otherwise, the screws may damage the
internal parts of the projector and cause malfunction.
•Install at a...

 
3.0  INSTALLATION 
12R599727 - BlackWing User Manual 
•The projection screen sizes and projecting distances in the table above are provided only as a guide. Please use
them as reference during installation. 
•Use a projection image of 16:9 aspect ratio for setup adjustment. 
3.8 Vertical lens shift 
This unit comes with a optical vertical shift feature that enables upward/downward adjustment of the projection
screen position. Adjust accordingly depending on the installation conditions.
•The shift level...

 
3.0  INSTALLATION 
R599727 - BlackWing User Manual13  
•Turn the shift adjustment screw using a screwdriver and adjust accordingly.
a) Turn clockwise: Screen shifts upwards.
b) Turn anti-clockwise: Screen shifts downwards. 
Once the Lens Shift Cover is removed, turn the Shift screw to modify the screen offset
clockwise to shift upwards and anti-clockwise to shift downwards. 
Mount the lens shift cover 
Mount the lens shift cover to this unit when the shift set up is completed. 
3.9 Using the Remote...

 
4.0  FEATURES AND CONNECTIONS 
14R599727 - BlackWing User Manual 
4.0 FEATURES AND CONNECTIONS 
4.1 General View 
Front side 
a) Lens Shift Cover
Remove this cover when using the Lens Shift feature for shifting the projecting position in the vertical direction.
Refer to “Vertical lens shift”,  page 12 for details.
b) and b’) Air inlets (2 in front and 1 at bottom surface)
The air inlets absorb air to cool the interior of the unit. do not block or allow warm air to blow into them. This may
cause the...

4.0  FEATURES AND CONNECTIONS
R599727 - BlackWing User Manual15 
When operating with the remote control, aim it towards the sensor. A remote sensor is also located at the front of
the unit.
d) AC Power Input Terminal
This is the AC power input terminal. Connect the supplied cord to this terminal.
e) [RS-232C] Terminal (D-sub 9 Pin)
This is the RS-232C interface-specific terminal. This unit can be controlled by a computer connected externally.
(refer to “RS-232C input”,  page 38 for details on the RS-232C...

4.0  FEATURES AND CONNECTIONS
16R599727 - BlackWing User Manual
4.3 Indicators
Indicator Display on the rear side
a) [STAND BY] Indicator
Light on:When in the standby mode.
Blinking:When in the cool down mode.
b) [OPERATE] Indicator
Light on:When this unit is currently operating (projecting).
c) [LAMP] Button
Light on:
When the lamp needs to be replaced soon or immediately.
When the lamp cover is removed.
When the lamp does not light up and the unit is unable to project, or when the lamp goes off during...

4.0  FEATURES AND CONNECTIONS
R599727 - BlackWing User Manual17 
Indicator Display on the digital control panel
4.4 Remote Control
Indicator
DescriptionSTAND 
BYOPERATELAMPTEMPFA NHIDE
Light On-----Unit is in standby mode
-Light On----Unit is in operate mode (during projection)
-Light On---Light OnWhen the video image is temporarily cleared 
upon pressing the [HIDE] button during 
projection
Blinking-----Unit is in cool down mode
(when cooling lamp)
--Light OnBlinking--About time to replace lamp
(Lamp...

4.0  FEATURES AND CONNECTIONS
18R599727 - BlackWing User Manual
a) Remote Control’s Signal Transmitter 
b) [OPERATE ON] Button
When this unit is in the standby mode, pressing this button for
more than 1 second will turn the unit on and cause the [OPER-
ATE] indicator to light up.
c) [LIGHT] Button
Lights up illumination (light) of the remote control buttons for about
10 seconds.
d) [CHP] (Cross Hatch Pattern) Button
Press this button to adjust the focus. Pressing this button projects
a green cross hatch...

4.0  FEATURES AND CONNECTIONS
R599727 - BlackWing User Manual19 
Battery insertion in the Remote Control
4.5 Connections
Connecting a video source with the Master Two
The BlackWing must be connected to a compatible device that can deliver 1080p50 or 1080p60 signals to the DVI-
D input.
To get the best performances, it is recommended to use the Master Two (R9011030).
In this configuration, the projection system would accept up to twelve different multi-standard sources. Each source
is automatically...

4.0  FEATURES AND CONNECTIONS
20R599727 - BlackWing User Manual
Connect the BlackWing to the Master Two with a HDMI to DVI-D Male cable.
Automation and control port : RS-232 input.
It is possible to control the BlackWing by connecting an automation system or a computer to the RS-232 port at the
rear of the projector.
Please request a connection cable from your distributor if needed.
Connect the BlackWing through the RS-232 port with an automation system or
computer.
Connecting the Power Cord
a) Before...