Cine Versum Cineversum Blackwing User Manual

7.0  ADVANCED SETTINGS
R599727 - BlackWing User Manual31 
232C link.
Color Temperature  settings
Color temperature can be selected to be D65, User1 or User2. (User1 and 2 allows a fine adjustment of the values
for red, green, and blue).
Color temperature stands for the spectral properties of a light source. Low color temperature implies warmer (more
yellow/red) light while high color temperature implies a colder (more blue) light. 
The color temperature can be set to the default value D65 that designs the...

8.0  MAINTENANCE
32R599727 - BlackWing User Manual
8.0 MAINTENANCE
8.1 Clean dirt on the cabinet
Always use a soft cloth. In case of heavy soiling, soak a cloth in neutral detergent diluted with water, wring dry and
wipe, followed by wiping again using a dry cloth.
CAUTION
Pay attention to the following as the cabinet may deteriorate in condition, get damaged or paint may come
off.
•Do not wipe with a stiff cloth.
•Do not wipe with force.
•Do not wipe with thinner or benzene.
•Do not spray volatile...

8.0  MAINTENANCE
R599727 - BlackWing User Manual33 
Procedure for Lamp Replacement
During the lamp replacement process, you may have access to sensitive parts of the projector.
•Open the lamp Cover, on the side of the projector.
•Loosen the 2 screws on the lamp unit and lift up the handle.
•Pull out the lamp unit.
•Insert the new lamp unit until it is fully in.
•Tighten the screws of the lamp unit and close the handle.
•Attach the lamp cover and fasten the screw.
Resetting Lamp Time
After installing a...

8.0  MAINTENANCE
34R599727 - BlackWing User Manual
Clean the filter with water and dry it, avoiding direct sunlight. In extremely soiled cases, use of a neutral detergent is
recommended.
Reinstall the inner filter
Check that the 2 claws at the left and right of the inner filter are locked to this unit. 

8.0  MAINTENANCE
R599727 - BlackWing User Manual35 
8.5 Troubleshooting
Full Screen Warnings
Warning indicators
MessageCause (Details)
No device is connected to the [DVI] terminal.
The DVI-D cable is connected to the [DVI] terminal
but there is no signal input.
Input the video signals.
A video signal that cannot be used with this unit has
been input.
Input a 1080/48p, 1080/50p or 1080/60p
video signals.
Upon pressing the [ZOOM T/W] or [FOCUS +/-]
button when Zoom/Focus of the Options menu is set
to...

8.0  MAINTENANCE
36R599727 - BlackWing User Manual
 If abnormality occurs in this unit during projection, the warning mode will be triggered and the type of abnormality
will be indicated by a combination of indicators displayed on the top surface of this unit.
This unit will then automatically stop projection and run the cooling fan for about 60 seconds.
Actions to be taken upon warning indications
Please follow the procedures below.
•For Nos. 1 - 4
No. 1: Perform procedures to turn off/on the power...

8.0  MAINTENANCE
R599727 - BlackWing User Manual37 
Before sending the unit to repair, check the following points.
This unit uses a microcomputer. External noise may cause it to malfunction. If this happens, turn off the
power and remove the plug from the power outlet. Insert plug again into the outlet and check operation of
the unit (see pages 22 on how to turn on/off the power of the unit).
SymptomProbable CauseCorrective Action
Power is not 
suppliedIs the power cord disconnected?Insert the power cord...

9.0  CONNECTION DETAILS
38R599727 - BlackWing User Manual
9.0 CONNECTION DETAILS
9.1 RS-232C input
Pin Assignment
External Control
Control of this unit is possible via a computer by connecting this unit to an automation device or computer with a
RS-232C cross cable (D-sub 9 pins). The commands to control this unit and the response data format against the
received commands are explained here.
Communication Specifications
Communication specifications for this unit are as follows:
Command Format
a) Command...

9.0  CONNECTION DETAILS
R599727 - BlackWing User Manual39 
c) Parameters used for the data format
The following 3 types of parameters are used for command and response data:
(1) Numeric value      (2) ON/OFF      (3) Special parameters
Each parameter is as follows:
(1) Numeric value
A 2-byte hexadecimal value (sign included) is represented by a set of 4-digit (4-byte) characters.
The range that can be specified is from 8000H to 7FFFH
(2) ON/OFF
Shows the status (ON or OFF) of the unit, such as POWER and...

9.0  CONNECTION DETAILS
40R599727 - BlackWing User Manual
9.2 DVI-D input
Pin Assignment
TMDS : Transition Minimized Differential Signaling
DDC : Display Data Channel
9.3 Screen Trigger  output
Location
The 12V DC trigger can be found at the rear of the projector next to the RS-232C input.
Functionality
When the projector is in operational mode, a 12V DC voltage is set on the Screen Trigger Output. When the projec-
tor is in standby, there is no voltage at the output.
This 12V voltage can be used to...