Christie Projector Mirage WU-L User Manual

Section 2: Installation and Setup
Mirage WU-L User Manual2-15020-100774-01 Rev. 2 (4-2012)
Mixed Serial Network (RS-232 and RS-422)
RS-422 serial communication is better over long distances than RS-232 communication. Use the RS-422 port 
only if your device has RS-422 capability. Always read the equipment literature before connecting. 
NOTICE: Connecting to the RS-422 port with incompatible equipment, including the wrong type of serial cable, 
can damage the projector.
In the RS-422 network the...

2-16Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 2: Installation and Setup
2.7 Projector Network Setup for ArrayLOC Communication
See the Integration Guide for detailed information about arrayLOC setup. 
2.8 Setting up the Image
2.8.1 Adjusting the Projection Lens
NOTICE: Lock lens adjustments to prevent unnecessary tampering.
Loosen the adjustment locks on the lens barrel before making adjustments.
2.8.2 Adjusting Image Geometry and Optical Alignment
Only perform image alignment once the...

Section 2: Installation and Setup
Mirage WU-L User Manual2-17020-100774-01 Rev. 2 (4-2012)
Folded Optics
In rear screen applications where space behind the projector is limited, a mirror may be used to fold the optical 
path, see Figure 2-6. The position of the projector and mirror must be accurately set - if considering this type 
of installation contact Christie Customer Support for assistance.
2.8.3 Boresight Alignment (Advanced)
1. Display the Boresight Test Pattern by pressing the Te s t key on the...

2-18Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 2: Installation and Setup
3. If boresight is required, see Figure 2-8 to understand how the adjustment screws on the lens mount affect 
the corresponding cross-hairs on the test pattern.
4. Use a 5mm Allen key to loosen the three locking setscrews on the lens mount, see Figure 2-9. 
NOTE:The setscrews must be backed out several turns, so that they do not contact the inner lens mount 
plate.
5. Fine tune the focus of cross-hair pattern I by...

Section 2: Installation and Setup
Mirage WU-L User Manual2-19020-100774-01 Rev. 2 (4-2012)
11. Lock the set screws and re-check the boresight quality. Tighten the setscrews enough to ensure they will 
not shift.
12. When the image is focused, lock adjustments in place by tightening the adjustments until just tight.
2.9 Adjust software to Optimize Image
NOTES: 1) See Section 3 for details on accessing and adjusting individual settings. 2) Unless otherwise 
indicated, instructions apply to all projector...

2-20Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 2: Installation and Setup
2.10 System Integration - GPIO Connector
The General Purpose Input-Output (GPIO) connector located on the Mirage WU-L projector input panel is 
used to enable control of stereo function. 
GPIO and External Devices
If you want to use GPIO to interface external I/O devices to the Mirage WU-L projector, you will need to have 
a custom adapter made. Seven GPIO pins on the 9-pin D-Sub GPIO connector are configured...

Section 2: Installation and Setup
Mirage WU-L User Manual2-21020-100774-01 Rev. 2 (4-2012)
2.12 Cleaning the Lens
Check periodically. A small amount of dust or dirt on the lens has minimal effect on image quality. To avoid 
the risk of scratching the lens, clean only if absolutely necessary.
Dust:
1. Brush most of the dust from the lens with a camel-hair brush or blow dust away with a dust-free blower.
2. Fold a microfibre cloth smooth and gently wipe remaining dust particles from the lens. Wipe evenly...

Section 3: Operation
Mirage WU-L User Manual3-1020-100774-01 Rev. 2 (4-2012)
3 Operation
 See Safety Warnings and Guidelines in 5 Maintenance.
This section describes the controls and switches used for basic projector operation once it is properly installed, 
aligned and configured by a Christie accredited service technician. You can access projector controls and 
settings with the IR remote, or with a laptop using the web interface. This chapter focuses on the use of the IR 
remote, and the projector...

3-2Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
3.1.1 IR Remote
Power Auto
Test Shutter
Input Slots
Slot 1
Slot 3Slot 2
Slot 4
PIP Swap
Menu
Channel
Gamma
13
2
46
5
7
9
8
0
Help FuncBright
ContrastExit
Proj Lens H
Lens VZoom Focus
Laser
InputOSD
10+
-  Press OSD to turn OffSwap
10+
Slots
Display the source from the next active input on thecard in the selected slot
Select an active or inactive 
input on any slot 
Laser Pointer Status LED
Plug In for Remote Keypad
These...