Christie Projector DHD555-GS User Manual

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-27
- Enter the IP address range, netmask and default gateway for the wire-
less LAN.
• SNMP Panel - The SNMP (Simple Network Management Protocol) interface provides network administrators with a common way to manage their network 
devices from a single remote location. SNMP allows an administrator to 
query a number of devices to see thei r current status/ configuration. It 
also allows operators to change conf iguration values and configure trap 
notifications to be sent when certain events occur. (eg. Loss of signal, 
power state change, etc)
 Emails are sent to the mail server configured in the projector  
settings. Up to 2 user email accounts can be selected. Any  
important information regarding the event will be located in the body 
content of the email.
 SNMP Traps are notifications that  are sent from the projector. They 
are only received by a trap receiver (MIB Browser) in the computer.
- SNMP Read Community (default setting: private) - this is a plain- text  password. This must also be ente red in the MIB browser. This pass-
word allows the various settings in the projector to be queried.
- SNMP Location (default setting: blank) - This field can be used as a  description to where a projector is located in a building. SNMP emails 
sent will specify this location.
- Trap IP Address (default setting: 0.0.0. 0) - This field must be filled in to 
receive Traps from the projector. The Trap IP Address should be filled in 
with the IP Address of the computer  on which you would like to view 
received traps.
- Trap Email 1/2 (default  setting: Blank) - The Trap Email 1 and 2 must be 
set to an email address that is config ured under the mail server that you 
will enter in the SMTP Server IP Address field.
- Email from Address (default setting:  blank) - the Email from Address 
that will appear as the sour ce of the SNMP emails.
- SMTP Server IP Address (default setting: 0.0.0.0) - Enter your mail  servers IP address.
• Trap Configuration Panel Set the SNMP actions for the system events. The dropdown options are: 
SNMP Trap + Email, Email, SNMP Trap, and Disabled.
•  Crestron Control System Panel Enter the IP address, IP ID, and Port of Crestron device for connection. 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-28
4.9.6 Tools
To Use the Tools tabbed pages to control Size & Position, Image Settings, 
Configuration, Light Source, Input Switching & PIP and Test Pattern.
4.9.7 Administrator Page
Add or delete a user or change password 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-29
4.9.8 About Page
• Version TabView the main firmware version, netwo rk firmware version, projector model 
name, and projector serial number.
• License Tab The license information of the computer program is displayed. 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-30
4.10 Christie Presenter
The Christie Presenter application allows a remote desktop from a host PC to 
be displayed on the network display through Ethernet, USB, or wireless 
transports. It can adapt to different network settings (DHCP, fixed IP, and direct 
link by USB/Ethernet cable).
Christie Presenter can be downloaded fr om the Christie website or from the 
web page of the projector.
4.10.1 Connect to the Projector
1. Connect to the projector using WiFi or Ethernet
- Ethernet connection:
Determine the projectors IP address from the menu Main Menu >  
Configuration > Communications > LAN
 Configure your PC IP address to be on the same network as the  
projector.
 The projector and computer must be  connected directly or over the 
network via Ethernet.
- WiFi Wireless connection: Insert the WiFi USB dongle (1DWUSB-BGN) into the USB port on 
the projector input panel.
Insert the WiFi USB dongle
K
HDBaseT REMOTE IN
GREEN/Y BLUE/PB RED/PR RS232 USB MINI USB
ETHERNET CVBS S-VIDEO
REMOTE
OUT HDMI VGA IN VGA OUT DISPLAY PORT DVI 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-31
Power on the Projector.
 Obtain the WiFi SSID from the OSD menu Main Menu >  
Configuration > Communications > WLAN
 Connect your PC device to the wireless SSID for the selected  
projector . Example: Christie@0111000123.
4.10.2 Install Christie Presenter software
1. Use a web browser to connect to the projectors network address (Default  
address 192.168.1.100)
2. Download and install the Christie Presenter Software 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-32
3. Configure the Christie Presenter Software. The name entered is used to 
identify all computers connected to the  projector via  the Christie Presenter 
software via either wired or wireless connections.  The Network Display 
Management -> Device Management tab will show all current connections.
4.10.3 Use Christie Presenter
1. Press the autorun icon in the system tr ay to pause or play the USB display. 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-33
2. After starting the Christie Presenter application, the main window can been seen (shown below).
Connect and search network display 1 Click the button   to enter into the connection menu section.
IconDescription
Connect and search network display
Stop/start displaying desktop contents to 
connected network display
Select display region
Configure Christie Presenter
Manage all connected network displays
Disconnect all connections 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-34
2 If the IP address of the projector is known, enter the IP address and click the Connect button. If the IP address is not known, click the 
Search button to search for the pr ojector on the network and select 
the projector to which you want to connect. Select the option Directly 
in order to proceed to the log in interface.
3 Input User type and Password in  the log-in interface. Select the 
display port (the default is full screen). Obtain the  Normal  users 
password from the OSD menu  Main Menu > Configuration > 
Communications > WLAN. 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-35
Select display regionOnce the connection is set up, click the button   to select the size of 
the projection region: FullScreen, FixedSize, or Alterable.
•  FullScreen: The default  capture mode turns to Full screen when the  
program is launched. At that time,  if screen capture starts, the image of  the 
whole screen is transferred to a remote network display.
•  FixedSize: FixedSize mode allows  the users to place a frame on the 
desktop. Only the image enclosed inside the frame is transferred to  remote 
network display.
•  Alterable: In Alterable mode the only region captured is the one  enclosed 
by the frame. The region can be enlarged or downsized by  dragging the 
eight small black squares scattered on eight edges of the frame. 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-36
Configure Christie PresenterClick the button   to configure Christie Presenter for Basic Setting  
and Advanced Setting.
•  Basic Setting: Select language, change the region size of fixed size  
capture mode, and select if noti fication message popup is allowed.
•  Advanced Setting: Select the qualit y of JPEG image, YUV sample format 
and network port setting. (The Fixed port is Port 5900)