Christie Projector DHD555-GS User Manual

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-17
For DWU Models 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-18
 
For DWX Models 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-19
4.6 Input Switching & PIP Menu
Main Input
From the list of active inputs, select one to be used as the main image.
PIP/PBP Input
From the list of active inputs, select one to be used as the PIP/PBP.
PIP/PBP Enable
Toggle between displaying two sources at once (Main and PIP/PBP images) or 
one source only. The check box turns the PIP/PBP source ON and OFF. Refer 
to Section 6.2 for the Main and PIP/PBP compatibility table.
Swap
Change the main image to PIP/PBP, and the PIP/PBP to main image. 
Swapping is available only when PIP/PBP is enabled.
Size
Select the PIP/PBP size to small, medium or large.
Layout
Set the location of the PIP/PBP image on the screen. 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-20
NOTE:PIP/PBP layout and size table as described below.
 P : indicates primary source region (lighter color).
 * : Both source regions are the same size.
Timing Detection
Select timing detection mode to wide or normal. It is used to support additional 
PC timings. When the projected picture is  not completed, this function is used 
to adjust the picture. Normal mode ca n support all of the 4:3 input sources. 
Wide mode can support all of the 16:9 input source & most of the 4:3 input 
source. For those 4:3 input sources not recognized by Wide mode (example
1400 x 1050), perform Auto Image using normal mode.
Source Info
Display current source settings (read-only).
Enable Source Hot-Key
Toggle the check box to enable or disable the main source hot-key.
Source Hot-Key
Allows you to assign a different source to the hot-key. Highlight an input and 
press ENTER to choose a different one.
PIP/PBP LayoutPIP/PBP Size
SmallMediumLarge
PBP, Bigger Left
Over-Under, Bigger Upper
PBP, Bigger Right
Over-Under, Bigger Lower
PIP-Bottom Right
PIP-Bottom Left
PIP-Top Left
PIP-Top Right
PPP
PPP
PPP
PPP
PPP
PPP
PPP
PPP
*
*
*
* 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-21
Input Key
Use it to list all of the sources or change the sources.
Blank on Signal Switch
When the function is enabled, the projector will blank the screen before timing 
is stable when change source.
4.7 Language Menu
Allows you to select an available language for the OSD display.
4.8 Test Pattern Menu
Choose the desired internal test pattern to display, or select OFF to turn off a 
test pattern.
• OFF
• Black
• White
• Checkerboard
• Grid
• Color Bars 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-22
4.9 Web User Interface
4.9.1 Logging On
Open your web browser and type the IP address (in the address bar) assigned 
to your projector.1 Select the log in level from the Access type drop-down list
2 Enter the Password in the Password field
3 Select the appropriate language  from the Language drop-down list.
4 Click the Press login button. The Main window appears.
4.9.2 Main Tabbed Page - General 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-23
• Control PanelSelect main source / PIP source, enable/disable PIP/PBP, change the 
layout / PIP size, swap, and change the test pattern.
•  Projector Information Panel
Check the projector information for power status, Pic mute status, OSD  
status, IP address and Mac address.
• Switch Panel Switch the on/off status of power, Pic mute, and OSD.
4.9.3 Main Tabbed Page - Status
Display the current status of light s ource, cooling (fans), version numbers and 
signal (source) information 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-24
4.9.4 Main Tabbed Page - Lens
Control the focus, lens shift and zoom adjustments for the lens. 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-25
4.9.5 Network 
						

							Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-26
• Restart NetworkExecute a Network restart. This will not change any of the network settings.
•  Network Factory Reset Execute a network factory reset. Network settings will be reset to the 
following default values:
- Projector Name = Christie@ + Serial Number
- Show Network Messages = ON
- LAN Settings:- Manual
- IP Address = 192.168.0.100
- Subnet Mask = 255.255.255.0
- Default Gateway = 192.168.0.100
- WLAN Settings: - Enabled
- Start IP = 192.168.1.100
- End IP = 192.168.1.120
- Subnet Mask = 255.255.255.0
- Default Gateway = 192.168.1.100
- SNMP Settings: - SNMP Read Communication = private
- Trap IP Address = 0.0.0.0
- SMTP IP Address = 0.0.0.0
- All other settings are cleared/blanked
- Trap Configuration: - All items = SNMP Trap + Email
•  LAN Setting Panel - Select if the projector must obtain an automatically assigned IP address through DHCP or if the user will set the address manually.
- Enter the IP address, netmask,  and default gateway address for the  
TCP/IP setting.
•  WLAN Setting Panel - Select if the wireless LAN of the projector is enabled or disabled.