Christie Projector DHD400S User Manual

							Section 4: USeR CoNTRolS
31
LAN (Standby)
Choose “On” to enable LAN connection. Choose “Off” to disable LAN 
connection.
VGA-2 (Function)
Input: Choose “Input” to let the VGA port works as a VGA input function.
•	
Output: Choose “Output” to enable the VGA Out function once the projector 
•	
is powered on.
Test Pattern
Display a test pattern.
Factory Reset
Choose “Yes” to return the parameters on all menus to the factory default 
settings.
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
32
Audio4.2.5 
Audio
On On On
Off
Speaker
Line Out
Microphone
Mute
Volume
Microphone Volume
Back
Enter
Select
Speaker
Choose “On” to enable the speaker.
•	
Choose “Off” to disable the speaker.
•	
Line Out
Choose “On” to enable the line out function.
•	
Choose “Off” to disable the line out function.
•	
Microphone
Choose “On” to enable the microphone.
•	
Choose “Off” to disable the microphone.
•	
Mute
Choose “On” to turn mute on.
•	
Choose “Off” to turn mute off.
•	
Volume
Press	the	◄	button	to	decrease	the	volume.•	
Press	the	►	button	to	increase	the	volume.•	
Microphone Volume
Press	the	◄	button	to	decrease	the	microphone	volume.•	
Press	the	►	button	to	increase	the	microphone	volume.•	
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
33
Options4.2.6 
optionsDefault
On
Off
Logo
Screen Capture
Auto Source
Input
Auto Power Off (Min)
Laser Settings
High Altitude
Filter Alarm (Hour)
Information
Back
Enter
Select
Logo
Use this function to set the desired startup screen. If changes are made\
 they 
will take effect the next time the projector is powered on.
Default: The default startup screen.
•	
User: Use stored picture from “Screen Capture” function.
•	
Screen Capture
Press	►	button	to	capture	an	image	of	the	picture	currently	displayed	on	
screen.
Screen capture in progress...
Please Wait.
NOTE:For successful logo capture, ensure that the on-screen image does not ex\
ceed the projector’s native  ™resolution. (1080P : 1920x1080 / UWHD : 1920x720).
“Screen Capture” is not available when 3D is enabled.
 ™
Before active this function, it is recommended that “Aspect Ratio”\
 is set to the “Auto”. ™
Auto Source
On: The projector will search for other signals if the current input signal \
is 
•	
lost.
Off: The projector will only search current input connection.
•	
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
34
Input
Press	►	button	to	enable/disable	input	sources.	The	projector	will	not	search	
for inputs that are not selected.
Input
Back
Enter
Select
VGA-1
VGA-2
HDMI-1
HDMI-2
Video
MULTIMEDIA
Auto Power Off (Min)
Sets the countdown timer interval. The countdown timer will start, when there 
is no signal being sent to the projector. The projector will automatically power 
off	when	the	countdown	has	finished	(in	minutes).
Laser Settings
Refer to page 35.
High Altitude
On: The built-in fans run at high speed. Select this option when using the 
•	
projector at altitudes above 2500 feet/762 meters or higher.
Off: The built-in fans automatically run at a variable speed according to the\
 
•	
internal temperature.
Filter Alarm (Hour)
Filters Alarm (Hour): Set the filter reminder time.
•	
Cleaning Up Reminder: Select “Yes” to reset the dust filter hour counter 
•	
after replacing or cleaning the dust filter.
Information
Display the projector information for model name, SNID, source, resoluti\
on, 
software version, and aspect ratio on the screen.
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
35
Options | Laser Settings4.2.7 
Hours Used (Normal)
Laser Settings
Hours Used (ECO)
Laser Power Mode Normal
Back
Select Enter
Hours Used (Normal)
Display the projection time of normal mode.
Hours Used (ECO)
Display the projection time of ECO mode.
Laser Power Mode
Normal: Normal mode.
•	
ECO: Use this function to dim the projector lamp which will lower power \
•	
consumption and extend the lamp life.
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
36
3D4.2.8 
3dAuto
Off
3D
3D Invert
3D Format
1080@24
Back
Enter
Select
3D
Auto: When a HDMI 1.4a 3D timing identification signal is detected, the \
3D 
•	
image is selected automatically.
Choose “On” to enable 3D function.
•	
Choose “Off” to disable 3D function.
•	
3D Invert
If you see a discrete or overlapping image while wearing DLP 3D glasses, you 
may	need	to	execute	“Invert”	to	get	best	match	of	left/right	image	sequence	to	
get the correct image.
3D Format
Use this feature to select the 3D format. Options are: “Frame Packing\
”, “Side-
by-Side	(Half)”,	“Top	and	Bottom”,	“Frame	Sequential”,	and	“Field	Sequential”.
1080p@24
Use this feature to select 96 or 144Hz refresh rate as using 3D glasses \
in 
the1080p @ 24 frame packing.
NOTE:
“Frame Sequential” is supported the DLP Link 3D input signals from\
 VGA/HDMI connector. ™“Frame Sequential”/“Field Sequential” are supported the HQFS\
 3D input signals from Video connector. ™“Frame Packing”/“Side by Side(Half)” / “Top and Bottom”\
 are supported from HDMI 1.4a 3D input signals. ™
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
37
Interactive4.2.9 
InteractiveOn
Interactive Settings
Back
Enter
Select
Interactive Settings
Choose “On” to enable Interactive function.
•	
Choose “Off” to disable Interactive function.
•	
You must to unplug the Mini USB cable that connects NB/desktop with 
the projector before using the Interactive function. After you complete the 
Interactive Settings in OSD, use Mini USB cable to connect NB/desktop wi\
th 
the projector.
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
38
LAN4.2.10 
laNDisconnected
On
Status
DHCP
IP Address
Subnet Mask
Gateway
DNS
MAC Address
Group Name
Projector Name
Location
Contact
Back
Enter
Select
Status
Display the network connection status.
DHCP
Configure	the	DHCP 	settings.
On: Choose “On” to let the projector to obtain an IP address automatically 
•	
from your network.
Off: Choose “Off” to assign IP, Subnet Mask, Gateway, and DNS 
•	
configuration manually.
IP Address
Display an IP address.
Subnet Mask
Display the subnet mask number.
Gateway
Display the default gateway of the network connected to the projector.
DNS
Display the DNS number.
MAC Address
Display the MAC address.
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
39
Group Name
Display the group name.
Projector Name
Display the projector name.
Location
Display the projector location.
Contact
Display the contact information.
CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015) 
						

							Section 4: USeR CoNTRolS
40CAPTIVA DUW350S/CAPTIVA DHD400S User Manual020-000816-01  Rev. 1 (07-2015)
How to use web browser to control your projector
Turn on DHCP to allow a DHCP 1. 
server to automatically assign an IP, or 
manually	enter	the	required	network	
information.
Choose apply and press
2.   button to 
complete the configuration process.
Open your web browser and type the IP 
3. 
Address from the OSD LAN screen. The 
web page will display as below:Based on network web-page for the 
4. 
input-string in [tools] tab, the limitation 
for Input-Length is in the below list 
(“space” and the other punctuation key 
included):
CategoryitemInput-Length 
(characters)
Crestron Control IP Address
15
IP ID 2
Port 5
Projector Projector Name
10
Location 9
Assigned To 9
Network  
Configuration DHCP (Enabled)
(N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User Password Enabled
(N/A)
New Password 15
Confirm 15
Admin Password Enabled
(N/A)
New Password 15
Confirm 15
NOTE:When you used the projector IP address, you will can not  ™
link to your service server.
Status
DHCP Connect
Off
IP Address
Subnet Mask
Gateway
DNS