Christie Projector D4K2560 User Manual

   Adjust the Image
D4K2560 User Manual41
020-101076-04 Rev. 1 (01-2015)
Adjust DMD convergence
A convergence problem occurs when one or more  projected colors (red, green, blue) appears 
misaligned when examined with a convergence te st pattern. Normally, the three colors should 
overlap precisely to form pure white lines throug hout the image and one or more poorly converged 
individual colors may appear adjacent to some or all of the lines. 
Contact your Christie accredited service technician to...

   Adjust the Image
D4K2560 User Manual42
020-101076-04 Rev. 1 (01-2015)
Adjust color by precise chromaticity values
1. On the touch panel controller, tap  Menu > Configuration  > Color Correction  > Select 
Color Adjustment .
2. From the list, select Custom .
3. Tap  Color Adjustments by X,Y .
4. Adjust the precise hues of each primary color component.
Adjust color by saturation
1. On the touch panel controller, tap  Menu > Configuration  > Color Correction  > Select 
Color Adjustment .
2. From the...

   Adjust the Image
D4K2560 User Manual43
020-101076-04 Rev. 1 (01-2015)
• Adjust the screw on the lamp side to move the image left or right. 
     
image
image
3mm
hex
driver
Base of projector
FRONT 

D4K2560 User Manual44
020-101076-04 Rev. 1 (01-2015)
Operation
This section provides information and procedures for operating the projector.
Projector LED status indicators
Turn the projector on
1. Set the breaker switch on the projector baseplate to the on position.
2. When the projector reaches standby, on the touch panel controller, tap  Home > Power .
For more details on the specified voltage range, see  Power requirements on page 78.
LEDStateDescription
Solid Green On Video electronics are on, the...

   Operation
D4K2560 User Manual45
020-101076-04 Rev. 1 (01-2015)
LED expected behavior on power up
The following table shows the expected behavior  of the projector LED and the MCPU board power 
LED on power up:
At approximately one minute and 15 seconds, the TP C indicates that it is connected and shows the 
home page.
Turn the projector off
1. On the touch panel controller, tap the  Home tab.
2. Tap  Power.
Work with lamps
This section provides information and procedures  for optimizing lamp...

   Operation
D4K2560 User Manual46
020-101076-04 Rev. 1 (01-2015)
Adjust the lamp position with LampLOC
Use LampLOC to configure the lamp position and geometry when installing a new lamp in the 
projector or at any other time when the lamp performance needs to be optimized. Before adjusting 
LampLOC, make sure the following criteria is met:
1. Make sure the lamp is on and the dous er (shutter) is open during adjustment. 
Christie recommends a 10-minute warm-up.
2. Perform the LampLOC procedure.
For more...

   Operation
D4K2560 User Manual47
020-101076-04 Rev. 1 (01-2015)
Track lamp intensity with LiteLoc
Use the LiteLoc feature to maintain a constant level of brightness over the lifetime of the lamp.
1. On the touch panel controller, tap  Menu > Lamp  > Lamp Power .
2. To adjust the lamp power, use the slider or enter a value until the display is as bright as  required.
3. Tap  OK.
4. Tap  Lamp Mode .
5. Tap  Constant Intensity .
Notice the Lamp Power option is greyed out so  you cannot adjust it. To...

   Operation
D4K2560 User Manual48
020-101076-04 Rev. 1 (01-2015)
A value of zero disables the feature.
3. Tap  OK.
When the specified number of hours is reached, a Lamp Hours - past expiry warning is issued.
Work with lenses
The lens mount secures the projection lens to  the projector and provides setup adjustments to 
correct boresight, and control focus, zoom, and offsets. 
4. To electronically control the focus, zoom, and  offsets, on the touch panel controller, tap the 
Lens  tab.
Select a channel...

   Operation
D4K2560 User Manual49
020-101076-04 Rev. 1 (01-2015)
Enable warping and blending
Use edge blending to combine several projecte d images into one single, seamless image. Use 
warping to project images on any surface shape.
1. Create the warp and blend files using the Twist applicationFor details, see the  Twist 2.0 User Manual (P/N: 020-101380-xx) .
2. Upload the warp and blend files to the projector. For details, see the  Twist 2.0 User Manual (P/N: 020-101380-xx) .
3. On the touch panel...

D4K2560 User Manual50
020-101076-04 Rev. 1 (01-2015)
Menus
This section provides information and procedur es for using projector menus. Use the projector 
menus to adjust projector settings and view status information.
Touch panel controller
The touch panel controller (TPC) is a touch-sensitiv e screen. Use the TPC to control the projector, 
manage sources, adjust the display, and view status information. The TPC is mounted on the rear of 
the projector and can be adjusted to improve the TPC viewing...