Christie Projector D13HD-HS User Manual

   Installation
HS Series User Manual21
020-000883-01 Rev. 1 (04-2016)
4. To turn on the projector, on the IR remote keypad press   or on the built-in keypad press  . 
The status LED is green with a long blink. 
5. To select an input source and turn it on, on the IR remote keypad select  Input Key. 
Available input sources are VGA, HDMI1, HDMI2, DVI, 3G-SDI, and HD-BaseT.
The projector detects the source you selected and displays the image.
Turning the projector off
Power off the projector in preparation...

   Installation
HS Series User Manual22
020-000883-01 Rev. 1 (04-2016)
• Position the projector to the required distance from the screen. The distance from the lens of 
the projector to the screen, the zoom setting, and the video format determine the size of the 
projected image.
• Determine the lens throw ratio: • Lens 0.84~1.02 (WU/HD)
• Lens 1.02~1.36 (WU/HD)
• Lens 1.2~1.5 (WU/HD)
• Lens 1.5~2.0 (WU/HD)
• Lens 2.0~4.0 (WU/HD)
• Lens 4.0~7.2 (WU/HD)
• 360 degree free orientation operation
Portrait...

   Installation
HS Series User Manual23
020-000883-01 Rev. 1 (04-2016)
Calculating the lens offset
Adjust the offset to align the imag e on the screen with full image size.
• The vertical image offset (shift) ranges for the projector are +/-60% (WUXGA) and +/-70%  (HD). 
• The horizontal image offset (shift) range for the projector is +/-25% (HD/WUXGA).
• The method for calculating lens offset complies with industry standards. For example for  Vertical lens offset:
• At 0% offset (or on axis), the center...

   Installation
HS Series User Manual24
020-000883-01 Rev. 1 (04-2016)
• Vertical image offset: +60%
• Vertical image offset: -60%
FUSE  T20A/250V~ 100V-120V~ FUSE  T15A/250V~ 200V-240V~
+60%
Lens center
FUSE  T20A/250V~100V-120V~FUSE  T15A/250V~ 200V-240V~
Lens center
-60% 

   Installation
HS Series User Manual25
020-000883-01 Rev. 1 (04-2016)
HD Projectors:
The following show vertical and horizontal image offset for HD projectors:
• Vertical image offset: +70%
• Vertical image offset: -70%
FUSE  T20A/250V~ 100V-120V~FUSE  T15A/250V~ 200V-240V~
Lens center
+70%
F
US E  T 20A /2 50V~
100V-120V~
FUSE  T15A/2 50V~ 200
V -24
0V
~
Lens center
-70% 

   Installation
HS Series User Manual26
020-000883-01 Rev. 1 (04-2016)
• Horizontal image offset: +/-25%
Removing and installing the lens
Warning! Failure to comply with the following could result in death or serious injury.
• Installing or replacing a lens must be done by  a Christie qualified service technician to avoid 
exposure to dangerous emission levels.
• To reduce emission intensity from the lens to s afe levels, lens rings must be used with 2.0-4.0:1 
and 4.0-7.2:1 lenses.
• Turn off the...

   Installation
HS Series User Manual27
020-000883-01 Rev. 1 (04-2016)
Installing the fuse
A fuse must be installed in the projector for it to power on.
1. Turn the projector off.
2. Choose the 20A or 15A fuse by sliding the AC cover to the right or to the left.
3. Remove the screw on the fuse.
4. Remove the fuse and replace it with the new one. 
• For regions using 200 to 240V-15A fuse.
• For regions using 100 to 120V-20A fuse.
• To order a fuse, see  Optional accessories on page 79.
FUSE  T20A/250V~...

   Installation
HS Series User Manual28
020-000883-01 Rev. 1 (04-2016)
Cleaning or replacing the filter
Regularly clean or replace the filters in the projector to ensure dust and other foreign materials are 
kept out of the projector. 
1. Turn off the projector.
2. Remove the screws on the filter cover using a 3 mm hex key.
3. Remove the filter cover.
4. Remove the filter from its compartment.
5. Clean or replace the filter.
Fog filters should be replaced after each use of the projector to a maximum of...

   Installation
HS Series User Manual29
020-000883-01 Rev. 1 (04-2016)
Installing the ceiling mount
Mount the projector with a Christie-approved mount (such as the Christie One Mount Plus, P/N: 
140-117100-XX), using the four mounting points on the underside of the projector.
1. Refer to the installation instructions and safety guidelines provided in the kit (such as the Christie One Mount Plus, P/N: 140-117100-XX).
Installing the projector in the rigging frame
Install the projector in a...

HS Series User Manual30
020-000883-01 Rev. 1 (04-2016)
Operation
The projector has multilingual on-screen display (OSD) menus so you can make image adjustments 
and change a variety of settings.
Most of the projector controls are accessed from within the projector menu system. Several groups of 
related functions are selectable from the Main Menu as shown below.
• To display the Main Menu, on the IR remote keypad or on the built-in keypad on the rear of the projector, press  MENU.
• To navigate within...