Christie Digital Systems Lwu505 User Manual

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada:
  AC Power Cord used in the United States and Canada is listed by the Underwriters 
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
  AC Power Cord has a grounding-type AC line plug.  This is a safety feature to be 
sure that the plug will fit into the power outlet. Do...

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
Part Names and Functions
CAUTION
Hot air is exhausted from the exhaust 
vent. Do not put heat-sensitive objects 
near this side. ƒ
Lens Release Button
„
Indicators
…
Lamp Cover 
†
Speaker
‡
Lens Cap
ˆ
Projection Lens
Do not cover the light beam in front of the 
lens. High temperature from light beam may 
damage the lens.
‰
Infrared Remote Receiver (Front & Top) 
Š Side Controls 
‹
Exhaust Vent
…
†Front
‹ Š„
ƒ
ˆ‰‡
Bottom Back‘  Œ
Ž

“...

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
ŠDIGITAL (DVI-D) TERMINAL
Connect the computer output digital signal to this 
terminal. The HDTV (HDCP compatible) signal can 
also be connected (pp.19-20).
’USB CONNECTOR (Series B)
Use this connector when controlling a 
computer with the remote control of the 
projector. Connect the USB terminal of 
your computer to this connector with a USB 
cable (p.19).
VIDEO INPUT JACK
Connect the component or the composite 
video output signal from video equipment...

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
ƒ
ON/STAND-BY button
Turn the projector on or off (pp.23-24).
„
MENU button
Open or close the On-Screen Menu (p.25).
‡
Point
x
z
{
y ( VOLUME – / + 
 buttons
– Select an item or adjust the value in the 
On-Screen Menu (p.25).
– Pan the image in Digital zoom + mode 
(p.43).
 

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
ƒSTAND-BY button
Turn the projector off (p.24).
…ON button
Turn the projector on (p.23).
ŽINPUT button
Select a signal (pp.33-35).
‰L-CLICK button
Act as the left mouse button for wireless mouse 
operation (p.32).
„SIGNAL EMISSION indicator
Light red while a signal is being sent from the 
remote control to the projector.
ˆPOINT
x
z
{
y( VOLUME – / +, MUTE) 
buttons
– Select an item or adjust the value in the 
On-Screen Menu (p.25).
– Pan the image in...

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
“ZOOM buttons
Zoom in and out the images (p.29).©D.ZOOM button
Select the Digital zoom +/- mode and resize the 
image (p.43).
”PIP button
Operate the Picture in Picture function (pp.30, 
55-56).
›  FILTER button
    Scroll the filter (p.30). ‘
FREEZE button
Freeze the picture on the screen (p.30).¨KEYSTONE button
Correct keystone distortion (pp.31, 44, 50).
•ON/OFF switch
When using the remote control, set this switch 
to “ON”.  Set it to “OFF” for...

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
12 3Open the battery 
compartment lid.Install new batteries into 
the compartment.Replace the 
compartment lid.
Two AAA size 
batteries
For correct polarity 
(+ and –), be sure 
battery terminals are 
in contact with pins 
in the compartment.
To ensure safe operation, please observe the following precautions :
 

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
The eight different remote control codes (Code 1–Code 8) are assigned to this projector. Switching the 
remote control codes prevents interference from other remote controls when several projectors or video 
equipment next to each other are being operated at the same time. Change the remote control code for 
the projector first before changing that for the remote control. See “Remote control” in the Setting Menu on 
page 58.
Press and hold the MENU and a...

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
Installation
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of 
the screen.
3Note:
 

LWU505 User Manual
020-000374-01 Rev.1 (01-2011)
When replacing the lens or using an optional lens, install the lens by following the instructions below. 
Ask the sales dealer for detailed information of the optional lens specifications. 
Shift the lens to the central position by using the 
Lens shift function (p.27).
1
2
Removing the lens
Lens release button
CAUTION
Be careful when handling the lens. Do not drop.
3
Installation
While pressing the Lens release button on the top
of the cabinet, turn the...