Christie Digital Systems Ds+5k, Kc-8k, Dw3k-6k, Kc, Hd5k, Kc-8k, Kc, Mirage S+2-4-8k, Dlv1400-dx, 1920-dx, Matrix S+2k, 4000, Hd4k Users Manual

  Appendix D: Throw Distance 
013-100199-04  D-27 
 
4.15 - 6.74 Zoom 
       
Image Diagonal  Image Width 
(W) Throw Distance 
(TD)  MAXIMUM ZOOM 
Inch cm Inch cm Inch cm  Throw Distance Formula 
76.8 195.0 66.9 170 471.6 1198.0 TD = 6.887 x W + 10.70
83.6 212.3 72.8 185 512.3 1301.3 Where W = image width (inch) 
90.3 229.5 78.7 200 553.0 1404.6  
97.1 246.7 84.6 215 593.7 1507.9 
103.9 263.9 90.6 230 634.3 1611.2 
110.7 281.1 96.5 245 675.0 1714.5 
117.4 298.3 102.4 260 715.7 1817.8 
124.2 315.5 108.3...

Appendix D: Throw Distance  
D-28 013-100199-04 
449.5 1141.6 391.7 995 2708.6 6879.7 
456.2 1158.8 397.6 1010 2749.2 6983.0 
463.0 1176.0 403.5 1025 2789.9 7086.4 
469.8 1193.2 409.4 1040 2830.6 7189.7 
476.6 1210.4 415.4 1055 2871.2 7293.0 
483.3 1227.7 421.3 1070 2911.9 7396.3 
490.1 1244.9 427.2 1085 2952.6 7499.6 
496.9 1262.1 433.1 1100 2993.3 7602.9 
503.7 1279.3 439.0 1115 3033.9 7706.2 
510.4 1296.5 444.9 1130 3074.6 7809.5 
517.2 1313.7 450.8 1145 3115.3 7912.8 
523.1 1328.6 455.9 1158 3150.5...

Appendix E 
System Integration 
 
013-100199-04  E-1 
The GPIO (General Purpose Input Output) connector located on the input panel provides a flexible 
method of interfacing a wide range of external I/O devices to the projector. There are seven GIO pins 
available on the nine-pin D-Sub GPIO connector, which are configurable via RS232 commands. The 
other two pins are reserved for ground and power – see table below for pin identification.  
 
GPIO Pins 
 
 
 
 
 
Pin #  Signal 
1  + 12V (200mA) 
2 GPIO 1...

Appendix E: System Integration   
E-2 013-100199-04 
Query Command 
(GIO?)  Request the state and configuration of all pins 
(GIO! “HHLLHLH” “OOIOOOI”)   Reply of pin state and configuration 
(GIO? C2)  Request configuration for pin #2 
(GIO! C2 O)  Reply with pin #2 configuration as output 
(GIO? 2)  Request the state of pin #2 
(GIO! H)  Reply with pin #2 state as high 
 
Real Time Event 
Use the serial command RTE to specify an action that is initiated at a particular time or based 
on an external...

Appendix F 
Optional Input Modules 
 
013-100199-03  F-1 
There are many optional input modules and accessories currently available for this 
projector. Contact your dealer for a complete and up-to-date listing. 
 
The RGB500 Input Module may be installed in this projector, a Marquee Signal 
Switcher, or a Marquee Case/Power Supply. The module receives analog RGB input 
signals from computers or other RGB source devices. 
 
RGB500 Features 
• Accepts 3, 4, or 5 wire RGB video (sync-on-green, composite...

Appendix G: Index  
F-2 013-100199-03 
The RGB400 ALT Input Module may be installed in this projector, a Marquee Signal 
Switcher, or a Marquee Case/Power Supply. The module receives analog RGB input 
signals from computers or other RGB source devices. Video inputs are 75
Ω 
terminated. Video outputs provide buffered loop-through to another display device. 
 
RGB400ALT Features 
• Accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or 
separate horizontal and vertical sync) 
• Accepts...

 Appendix G: Index 
013-100199-03   F-3  
Features 
• Supports Digital Visual Interface (DVI) single-channel  
• Supports VESA® Extended Display Identification Data (EDID™)  
• Provides an active-loop-through using a DVI connector (conforming to the 
DVI Specification) 
 
The module accepts a serial digital 4:2:2 component video signal (YCbCr) via a single 
SERIAL IN BNC connector. The signal can loop through the SERIAL OUT BNC out to 
another device (such as another projector). Inputs are 75
Ω...

 
Index 
 
013-100199-03 G-1   
3 
3D Simulation, 34 
3D Stereo Sync, 34 
A 
Ambient Lighting, 5 
Anamorphic, 22 
Arrow Keys, 9 
Auto Input Level, 30 
Auto Key, 5 
Auto Setup, 5 
AutoSource Checkbox, 19 
B 
Backlight, 41 
Bad Sync, 70 
Baud Rate, 17, 38 
Blacklevels and Drives, 30 
Blanking, 24 
Brightness Key, 7 
Brightness Uniformity 
Canceling, 64 
Definition, 60 
Prerequisites, 60 
Procedure, 60 
Submenu, 43 
Broadcast Key, 41 
Broadcasting, 9 
Built-in Keypad, 1 
C 
Cables 
Serial Communication, 1...

Appendix G: Index  
G-2 013-100199-03 
Custom Sizing, 20 
D 
Dark Interval, 34 
Date and Time 
Setting, 37 
Decoder AGC 
Enabling, 28 
Decoder Luma Delay, 29 
Detail 
Threshold, 36 
Diagnostics and Calibration, Submenu, 
46 
Display 
Channel List, 37 
Error Messages, 38 
Slidebars, 37 
DVI, 14 
E 
Edge Blending, 43 
Description, 64 
How Blends are Used, 64 
Main functions, 64 
Procedure, 66 
Enter Key, 9 
Error Messages 
Bad Sync, 70 
H-Sync or V-Sync, 70 
No Signal, 70 
System Warnings/Errors, 70...