Christie Digital Systems Ds+5k, Ds+8k, Dw3k, Dw6k, Mirage S2k, S4k, S8k, Matrix 4000, Dlv1400-dx Users Manual

							Section 3: Operation 
 
  
 User’s Manual     3-55. 
coordinate you select will then automatically trigger a full field display of the 
corresponding color. 
Alternatively, use the Color Saturation menu for these adjustments or to fine tune. 
NOTE: For speed, enable the “Auto Color Enable” checkbox. Each color coordinate 
you select will then automatically trigger a full field display of the corresponding 
color. 
These coordinate adjustments move 
the three color points closer together 
(see right) to establish a “shared” 
gamut attainable by all projectors in 
your group. Adjust only as necessary 
to ensure that the resulting color 
palette is as large as possible. When 
done, you may need to adjust lamp 
power slightly. 
7.  All screens should now be color-matched. Apply this new “User” gamut to a 
source at any time by selecting it in the “Select Color Adjustment” list accessed in 
the Advanced Image Settings menu. 
Using the Color Saturation Menu for Color Matching 
You may prefer to use the 
Color Saturation menu to 
match colors across 
multiple screens. In the 
three Color Adjustment 
submenus (Red, Green, 
Blue—see right), set all 
main values to 100 and 
the secondary values to 0. 
Then judge by eye and 
adjust the slidebars as 
needed. Note that 
adjustments here define 
new x/y coordinates in the 
Color Adjustments by X,Y 
menu. 
For best results, use this 
menu after doing the color 
adjustment procedure. 
 
WHAT IS BRIGHTNESS 
UNIFORMITY? 
When used to refine screens already matched for their primary colors 
(see Matching Colors in Multiple Screens, above) and overall light output, proper 
adjustment of Brightness Uniformity can create an exceptionally smooth screen in 
which: 
• no area of the screen appears more red, green or blue than another  
 
Figure 3.29. Color Matching Using 
Color Saturation Menu 
 Achieving Brightness 
 Uniformity  
						

							Section 3: Operation 
3-56   
  User’s Manual      
• no area of the screen appears brighter than another 
• color and light output from one screen closely matches adjacent screens 
Although the Brightness Uniformity control can be used for a stand-alone projector, it 
is particularly useful for setting up and maintaining tiled images that form a cohesive 
display wall in which the color “cast” and light output appear uniform throughout 
each image as well as throughout the entire wall. The procedure provided here 
assumes a multiple-screen application. 
 Before You Begin 
Read through the entire procedure before attempting to adjust Brightness Uniformity 
controls, and keep in mind the following checklist of prerequisites and guidelines:  

						

							Section 3: Operation 
 
  
 User’s Manual     3-57. 
1b) Enable the 
Brightness 
Uniformity 
checkbox. This will 
enable access to the 
uniformity controls 
and will apply the 
settings to your 
image. 
 
1c) Select the 13 Point test pattern for display. 
This pattern provides 9 screen “zones” with 
13 targets.  
FOR BEST RESULTS: Rather than examining 
the CENTER of each zone when assessing 
Brightness Uniformity adjustments, focus on 
extreme EDGES as indicated in the 
illustration at right. 
1d) In either Color Adjustments menu, select a “User” color. Then: 
• If you have created a “User 1” color gamut (recommended) for a well-matched wall, 
continue to Step 
1e. 
• If you prefer maximum brightness rather than a particular color temperature, select “Max 
Drives”. 
 IMPORTANT  
Do not change User 1 Color Adjustment 
in color-matched applications! 
1e) In the White Uniformity 
menu, set the “Overall” 
output level to 50.0 and all 
remaining slidebars to 0.0. 
This decreases the light 
output just enough 
throughout the screen so that 
any color level can then be 
increased later as necessary 
for matching light output 
from zone-to-zone. Do not 
exceed 50.0 for “Overall”—a higher level will likely interfere with achieving 
brightness uniformity and is not recommended. 
Ensure that overall light output remains well-matched from one screen center 
to the next. Where necessary, increase or decrease Lamp Power slightly to 
recover center matches. 
 
 
 
 
 
  
						

							Section 3: Operation 
3-58   
  User’s Manual      
Step 2: Adjust Color (level of red/green/blue) in 8 Zones 
NOTES: 1) At this point, ignore the brightness of individual zones. 2) Always ignore 
menu colors. 
2a) On each screen, compare the color temperatures in the 8 target zones (4 edges 
and 4 corners) to that of the color temperature of the center. Compare using a 
white field only, and take note of any areas that do not match the center. Also 
decide if any screen exhibits a more obvious color shift than other screens—
begin with this screen in Step 
2b.  
2b) Return to the Brightness Uniformity menu. Beginning with the screen that exhibits 
the most obvious color shift(s), for each edge that exhibits a noticeably different 
color temperature from the center, select the corresponding Uniformity adjustment 
menu—Left, Right, Top or Bottom. For example, if any part of the left side is too 
blue, too red or too green, go to the Left Uniformity menu and adjust the colors 
(i.e., change their light output) until all portions of the left side closely match the 
center color temperature. Adjust an edge first (focusing on its center), then adjust 
its corners. See Figure 3.30. 
 
Figure 3.30. Match Zones to Center Color Temperature 
Repeat the color adjustment of sides and corners for each edge of the screen that does 
not yet match the center (note that each corner is adjustable in either of its two 
adjacent “side” menus). When done, all areas of a given screen should match. Repeat 
Steps 
2a & 2b for all remaining screens. 
Step 3: Adjust Light Output in 8 Zones 
3a) For each screen, compare the light output of each edge and corner to that of the 
center. If any of the areas differ, use the White Uniformity menu to match edges 
and corners to the center as described below (see Figure 3.31). Begin with the 
screen exhibiting the most obvious variations in light output. 
• Adjust edge White Uniformity first—note that each edge adjustment also affects the rest of 
the screen slightly. Keep all edges just slightly lower than the center light output rather 
than matching light output precisely. Otherwise, it may not be possible to brighten the 
corners (typically the dimmest areas of the screen) enough. I.e., the best uniformity is a 
compromise between the brightest and darkest areas of the screen.
 
• 
Adjust corner White Uniformity last—each corner adjustment affects only this quadrant.  
• 
Repeat for each screen.   
						

							Section 3: Operation 
 
  
 User’s Manual     3-59. 
 
Figure 3.31. Match Zones to Center Light Output 
Step 4: Readjust Color Temperature (level of red/green/blue) in 8 Zones 
4a) Return to Steps 2a & 2b and, if necessary, fine tune the zones so that they all 
still exhibit a single color temperature. 
Canceling Brightness Uniformity 
If you do not want to use or apply Brightness Uniformity settings, delete the 
checkmark from the “Uniformity Enable” checkbox at the top of the Brightness 
Uniformity menu. 
Christie Edge Blending is an innovative set of software functions that can quickly and 
easily blend whitelevels along the edges of multiple adjacent projected images to 
create a single seamless larger image. 
What is a Blend? 
In simple terms, a blend appears as a gradient strip 
along an edge of a projected image. It is darkest along 
the extreme edge of the image, and lightens nearer to 
the rest of the image (see right). 
How Are Blends Used? 
In multiple-projector walls, complementary blends 
between neighboring images can compensate for the 
extra “brightness” or intensity where these edges overlap. By controlling blend width 
and other properties, you can achieve uniformity across the group of images. Visible 
overlaps will disappear: 
 
Figure 3. 32. Edge Blending Concept 
For best results, use the same projector model and type throughout your display wall. 
In addition, avoid high-gain screens whenever possible—the optical performance of 
such screens demands minimal image offset, thus projectors must be located very 
close to one another.   Ed
ge Blending 
  
						

							Section 3: Operation 
3-60   
  User’s Manual      
Edge blending software controls are located in the 2-page Edge Blending submenu—
access via Configuration menu, then go to the Geometry and Color menu and select 
Edge Blending. The More option opens the second page of the Edge Blending 
submenu. 
Main Functions 
Use edge blending controls to set the precise width, shape and midpoint you need to 
blend overlapping edges together smoothly. 

						

							Section 3: Operation 
 
  
 User’s Manual     3-61. 

						

							Section 3: Operation 
3-62   
  User’s Manual      
 
Figure 3.35. Set Starting Points for Each Projector 
4. SET BLEND WIDTH: On one projector, increase the Blend Width for an overlapping 
edge (for example, if the projector’s image is on left, its right edge overlaps the 
adjacent image—adjust Right Blend Width). Use the same setting on the second 
projector for this shared edge. 
5.  Re-adjust width (both projectors) until the overly bright band at the midpoint of the 
overlapping blends disappears or just changes to very light gray. For the shared 
edge, use the same Blend Width setting on each projector. If the “best blend” 
appears to be between two settings, choose the wider setting for both projectors. 
6. 
CHECK BLEND: If the blended region appears too dark or light in relation to the rest 
of the image: 

						

							Section 3: Operation 
 
  
 User’s Manual     3-63. 
VIA WEB INTERFACE — Connect your PC to the projector’s Ethernet port. In your web 
browser (Internet Explorer, for example), enter the IP address of the projector you 
wish to control. This will start a password-protected ChristieNET application—enter 
the factory default “
ccm7” login and password to open the program. If the projector is 
powered up, you can access assorted menu options and slidebars. 
Repeat for remaining networked projectors as desired. Keep in mind that multiple 
units can be controlled from one PC, but each unit will be in its own ChristieNET 
interface (web browser) at the PC. Likewise, you can make up to five separate web 
locations to a single projector. 
The default login provides access to security settings, where you can define other 
users with the same or fewer rights. Use “unlimited” rights for most applications. For 
all logins, the Service menu is still protected with its own password. 
NOTES: 1) Any proxy server settings that interfere with this type of link should be 
disabled for using ChristieNET. Disable through Internet Explorer’s < Tools> 
  . 2) Your PC must be Java-
enabled to v1.4.2 or higher to run ChristieNET. 3) Depending on your projector 
model, certain controls provided through ChristieNET are non-functional. 
 
Occasionally the projector will encounter an error condition that can interrupt normal 
operation. Such a condition can be caused by a simple invalid keypad entry, an input 
signal error (most common) or a system error. The manner in which users are to be 
notified of error conditions is set in the Menu Preferences menu: 
• To see error messages displayed on-screen, select the “
Screen” or “All” option. 
• To be notified via a serial communication only, select the “
RS232” option. 
•  To receive both types of notifications, select “
All”.  
• To disable error messages (except for “invalid user key entry”, which can’t be 
hidden), select “
Off”. 
Note that a two-digit error code appears in the status LED display window located 
beside the built-in keypad at the rear of the projector. Normal operation is indicated by 
the “0n”status code. 
 
 
Invalid User Entry 
A keypad entry not recognized by the projector triggers a short on-screen error 
message identifying the problem. For example, if you specify a channel number that is 
not available, the message “Invalid Channel will appear. Or if you try to enter the 
wrong password, you’ll see “Invalid Password”. Press 
 or Ex i t to clear the 
message and try again. 
NOTE: On-screen display of “Invalid User Entry” messages cannot be disabled, even 
if Display Error Messages has been set to “Off”. 
3.12 Error 
Conditions 
 User Errors  
						

							Section 3: Operation 
3-64   
  User’s Manual      
An input signal error message occurs if you are in presentation level (i.e., there are no 
menus present) and have selected an input on which the projector detects a problem. 
While menus remain operational and any key press will temporarily remove any 
displayed error message, you must resolve the signal problem in order to permanently 
eliminate the message. 
No Signal 
The message No signal occurs when there is no source signal detected at the 
selected input—both HSYNC and VSYNC are inactive and the screen background is 
black. Connect or correct the signal, or try another input. 
Bad Sync 
The message Bad Sync occurs when HSYNC or VSYNC are active but the signal 
cannot be displayed. Such a condition occurs when only one of the two sync signals is 
present or when either sync signal is unstable or of the wrong frequency. Correct the 
signal or select another input. 
Other Signal Error Messages 
In addition to the common Bad Sync and “No Signal” errors, you may encounter a 
signal error message indicating that HSYNC and/or VSYNC are either too fast or too 
slow. When such a message appears, check the frequencies shown in the Status menu. 
If they are correct, then the signal is not recognized by the projector. On some PCs 
you may be able to change the settings to generate a compatible signal. If the 
frequencies shown in the Status menu are incorrect, check the cabling to see where the 
problem might originate. 
When the projector encounters a system malfunction, either a System Warning 
message or a System Error message may appear. Both types of messages are 
accompanied by a numerical error code on the status LED display. A system 
malfunction can be cleared with 
Ex i t Ex i t  from presentation level, but may indicate 
the need for service by a qualified service technician. 
NOTE: System messages appear on-screen only if Display Error Messages has been 
set to “Screen” or “All”. 
System Warnings 
A system warning indicates that a system malfunction has been detected (see Status 
LED Codes, below). A system warning message replaces any input signal message 
and disappears when the input signal status changes. While the projector will remain 
operational, the message indicates the presence of a potentially serious problem that 
should be investigated. You can press 
Ex i t Ex i t to remove the message, but for best 
results you should reset the projector—power the projector down and up again with 
the 
 (power) key. 
System Errors 
A system error message indicates that a serious malfunction has been detected and 
must be investigated as soon as possible (see Status LED Codes, below). The projector 
will no longer operate and must be reset—power the projector down and up again 
with the 
 (power) key.   In
put Signal Errors 
 System Warnings / Errors