Christie Digital Systems Ds+4k, 8k, Dlv1400-dx, Mirage S+2k, 4k, 8k Users Manual

Section 4: Maintenance 
 
  
 User’s Manual     4-9. 
 
Use the following instructions when replacing a projection lens: 
NOTE for first time use: The projection lens is shipped separately from the 
projector. Before you install a lens it is important that you remove the lens plug from 
the lens opening in the projector.  
1.  Power down the projector and wait 5 minutes to allow the lamp to cool before 
continuing with Step 2.  
2.  Place the lens cap on the projection lens to protect it from being...

Section 4: Maintenance 
4-10   
  User’s Manual      
 
        
Figure 4.8. 
  

Section 5 
Troubleshooting 
 
 User’s Manual     5-1 
 
If the projector does not appear to be operating properly, note the symptoms present and use the following guide to 
assist you. If you cannot resolve the problems yourself, contact your dealer for assistance. 
NOTE: A qualified service technician
 is required when opening the projector to diagnose any “probable cause”. 
 
 
The projector is on but there’s no display... 
1.  Was a lens cover accidentally left on? Remove lens cover. 
2.  Make sure...

Section 5: Troubleshooting 
5-2   
  User’s Manual      
The upper portion of the display is waving, tearing or jittering… 
1.  This can sometimes occur with video or VCR sources. Check your source. 
Portions of the display are cut off or wrap to the opposite edge… 
1.  Resizing and/or blanking may need adjustment. 
2.  The horizontal or vertical scan frequency of the input signal may be out of range 
for the projector. Refer to Section 6, Specifications for scan frequency ranges. 
The display appears...

Section 5: Troubleshooting 
 
  
 User’s Manual     5-3. 
The display is “noisy”… 
1.  Display adjustment at your input source may be required. Adjust pixel tracking, 
phase and filter. Noise is particularly common on YPbPr signals from a DVD 
player. (If using a PC source, adjust using a high-frequency test pattern with one 
pixel on/off throughout.) 
2.  The video input may not be terminated. Make sure the video input is terminated 
(75Ω). If it is the last connection in a loop-through chain, the video...

Section 6 
Specifications 
 
 User’s Manual     6-1 
 
NOTES: 1) Due to continuing research, specifications are subject to change without notice. 2) 
Specifications apply to all models unless otherwise noted. 
 
 
Resolution 
SXGA+ (1400 x 1050) 
Achievable Brightness (* all values +/-10%) 
Mirage S+2K (500W)  2000 ANSI lumens 
Christie DS+4K, Mirage S+4K (1000W)  5000 ANSI lumens 
Christie DS+8K, Mirage S+8K (1200W)  8000 ANSI lumens 
DLV1400-DX (500W)  2000 ANSI lumens 
 
Contrast Ratio (ANSI, full...

Section 6: Specifications 
6-2   
  User’s Manual      
Standard Analog RGB or YPbPr (Interlaced or Progressive Scan Format) 
Horizontal Frequency Range  31 – 120 kHz 
Vertical Frequency Range (See Note 2)  23.97 – 150 Hz 
Scan format  Interlaced or progressive 
Pixel Clock Rate (max.)  220 MHz max  
Signal Format  Analog RGB, YPbPr, Composite (on 
“G, PB” input and S-video (luma on 
“R/Pr/Y” input and chroma on 
“B/Pb/C” input) 
Input Levels   R, G, B, - with sync:  1.0V
p-p ±2 dB 
      R, G, B, -...

Section 6: Specifications 
 
  
 User’s Manual     6-3. 
DVI-I Input 
Interface Standard  DDWG DVI 1.0 
Color Space  RGB or YPbPr 
Horizontal Frequency Range  31 – 120 kHz 
Vertical Frequency Range  23.97 – 150 Hz 
Pixel Clock Rate  25 – 165 MHz 
Scan Format  interlaced or progressive 
Active Pixels per scan line  640 min., 2048 max. 
Active Lines per field / non-interlaced frame  200 min., 1536 max 
Connector type  DVI-I 
NOTE: HDCP compatible 
RS-232 Serial Input 
Connector Type  1 female 9-pin Dsub...

Section 6: Specifications 
6-4   
  User’s Manual      
 
 General  
Voltage range  
 500W models  100 – 240VAC 
 1000W models
 100 – 240VAC 
 1200W models  200 – 240VAC 
Line frequency   50 Hz – 60 Hz nominal 
Max. Inrush current  60A max. 
Current rating  
 500W models  10A @ 100V, 5A @ 200V 
 1000W models
 12A @ 100V, 8A @ 200V 
 1200W models  10A @ 200V 
Power consumption  
 500W models  1000 W max. 
 1000W models
 1600 W max. 
 1200W models  2000 W max. 
Current rating or AC input connector   15A...