Christie Digital Systems Ds+4k, 8k, Dlv1400-dx, Mirage S+2k, 4k, 8k Users Manual

Section 3: Operation 
 
  
 User’s Manual     3-69. 
Table 3.5  Error Codes 
Code Description 
GENERAL 12  Software bug. Contact dealer/factory. 13  CRC error in flash ROM. Download new software. 14  Engineering-only programming is complete. Call Christie, replace TIPM. 15  Attempting to download code without being in boot mode 16  Invalid interrupt. Power off/on. If it persists, contact dealer/factory. 17  User forced system to stay in boot mode 18  Jumper for programming boot not installed LAMP...

Section 4 
Maintenance  
 
 User’s Manual     4-1 
 
The projector is an international regulatory agency approved product designed for safe 
and reliable operation. To assure complete safety at all times it is important to 
acknowledge the following precautions while operating the projector.  
 WARNING 
Always remove the lens when shipping the projector. 
 WARNING 
NEVER look directly into the projector lens.  
The high brightness of this projector 
could cause permanent eye damage. 
 WARNING 
For...

Section 4: Maintenance 
4-2   
  User’s Manual      
◊ Only use Christie-approved ceiling mount fixture, if the projector is to be ceiling 
mounted.  
Lamp: The projector uses a Cermax Xenon lamp to deliver its high brightness. A 
lamp should be replaced when it has reached its end of life (1000 hrs, typical) or if a 
noticeable change in brightness occurs. Keep track of the number of hours the lamp 
has been in use (Lamp Menu) and be aware of any changes to brightness. These 
indicators will help you...

Section 4: Maintenance 
 
  
 User’s Manual     4-3. 
Slots and vents in the projector provide ventilation. Never block or cover these 
openings. This ensures reliable operation of the projector and prevents overheating.  
◊ Do not place the projector over a radiator or heat register. The projector should 
not be placed in an enclosure unless proper ventilation is provided. 
◊ Do not insert objects into the ventilation openings of the projector. They may 
touch dangerous voltages or short-out components...

Section 4: Maintenance 
4-4   
  User’s Manual      
 
 WARNING 
Always power down and unplug the projector before 
cleaning or servicing. 
Table 4.1. Maintenance Guide 
Part Description Frequency Action 
Lens  As required 
CLEAN: Clean if absolutely necessary. A 
small amount of dust on the lens has very 
little affect on picture quality. 
To clean: Apply a solvent such as acetone, 
alcohol or vinegar sparingly to clean, lint-
free lens tissue. Wipe across the surface of 
the lens. Do not scrub or rub...

Section 4: Maintenance 
 
  
 User’s Manual     4-5. 
 
The optional IR remote uses two AA size, 1.5V alkaline batteries. To replace the 
batteries simply turn the remote over and push out the cover using the finger groove, 
as shown in (1) Figure 4.1.  
Remove and properly discard the old batteries. Insert new batteries in the proper 
positive/negative orientation as shown etched in the bottom of the compartment (2). 
Replace the cover by inserting the tabbed end into the opening and snapping the...

Section 4: Maintenance 
4-6   
  User’s Manual      
 
 WARNING 
Handle lamp with care. Lamp may explode if dropped. 
Wear protective clothing and safety goggles when 
handling lamps. 
Use only Christie approved lamps provided in Lamp and 
Filter Service Kits for your projector. 
1. Press  to power down the projector. Wait at least 5 minutes to allow the 
internal cooling fans to stop before unplugging the projector. This wait period 
is also required to allow the lamp to sufficiently cool before...

Section 4: Maintenance 
 
  
 User’s Manual     4-7. 
 
Figure 4.4. 
5.  Align the new lamp with the top and bottom guides on the left side of the 
lamp compartment. (Figure 4.5.) Slide the lamp all the way in – a slightly 
harder push may be required right at the end to make sure it is fully seated 
into the terminal block. NOTE: The projector will not power up again if the 
lamp is not fully connected to the terminal block.   
 
Figure 4.5. 
6.  Pull (out) and turn the lamp lock lever (turned up in...

Section 4: Maintenance 
4-8   
  User’s Manual      
The two filters located at the front 
and left side of the projector 
should be replaced whenever the 
lamp is replaced. If you are 
working in an extremely dusty 
environment you may want to 
replace the filters sooner. Use the 
filters provided in the Christie 
approved Lamp and Filter Kit for 
your specific projector model 
(Table 1.)  
Tools required: #1 Phillips 
screwdriver 
 
1.  Loosen the screw(s) from the 
filter access panels. The front...