Christie Digital Systems Cp2215 User Manual

							CP2215 User Manual53020-101225-01 Rev. 1 (01-2014)
View and Modify Projector
Settings
Use the procedures in this section to modify projector settings including the touch panel controller 
(TPC) language, TPC screen brightness, and time settings. 
Set Projector and TPC Preferences
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > Preferences.
2. Adjust these settings:
Adjust Projector Time Settings
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > Time Setup.
2. Adjust these settings:
FieldDescription
Temperature Units Display temperature information in Celsius or Fahrenheit.
Image Orientation
The direction of the on screen image.
Luminance Units Display luminance information in Foot Lamberts or Candela.
Language The language for the TPC.
Beep on Screen Press When selected, a sound plays when you tap the TPC screen.
Enable Screen Saver / Screen 
Saver DelayEnables a screen saver and determines the frequency that the 
screen saver appears.
Over Temperature, Fan Failure, 
Lamp Rotation, Lamp Expiry, 
Lamp Half Life warning, Light 
Intensity Warning, LD Log 
WarningOpens an alarm window when a pre-defined event occurs.
Brightness Adjusts the brightness of the touch screen display.
Calibrate Screen Opens the Calibrate window and starts the TPC calibration. 
FieldDescription
Time Zone The time zone where the projector is installed. 
						

							54                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
View and Modify Projector Settings
Modify Projector Communication Settings
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > Communications Configuration.
2. Complete these fields:
Add a Network Device
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > Network Devices Setup.
24 Hour Time  Displays time in a 24-hour format.
Adjust for Daylight Savings Time Automatically adjusts the time for daylight savings.
Date and Time Adjusts the projector date and time.
Set Time Applies the date and time adjustment settings.
Enable NTP Turns Network Time Protocol (NTP) clock synchronization on.
NTP Server The NTP server IP address.
Test NTP Tests the NTP server settings.
FieldDescription
Device Name The name of the projector.
IP Address The IP address of the projector. 
Subnet Mask The subnet mask to which the address belongs.
Gateway The IP address for the network gateway.
Apply Applies Ethernet settings.
Serial Speed (Baud) The baud rate of the serial port. The default is 115200. 
Enable SNMP Enables SNMP. 
SNMP V2 / SNMP V3 The SNMP protocol type. Contact Christie for the SNMP V3 user ID and 
password.
Management IP The IP address where SNMP information and notifications are sent. 
Download MIB to USB
Sends the SNMP Management Information Base (MIB) file to a USB flash 
drive. 
Apply Applies SNMP settings.
Serial Access
Grants access to serial connections.
Ethernet Access
Grants access to Ethernet connections.
FieldDescription 
						

							   View and Modify Projector Settings
CP2215 User Manual55020-101225-01 Rev. 1 (01-2014)
2. Tap the check box. If the check box is not selected, the device does not appear in the Network 
Devices menu.
3. Tap the Launch Dialog   icon in the Device Name field and enter a name for the network 
device.
4. Tap Enter.
5. Tap the Launch Dialog   icon in the URL field and enter the URL for the network device.
6. Tap Enter.
Access a Network Device
Tap Menu > Network Devices > Christie ACT
To interact with the device tap   in the top right corner of the window.
Calibrate the Internal Light Meter
To calibrate the internal light meter to Foot Lamberts you use the Foot Lamberts Calibration wizard. If 
content is playing when you run the Foot Lamberts Calibration wizard, playback stops. To run the 
Foot Lamberts Calibration wizard you need Administrator or Service permissions.
1. Tap Menu > Administrator Setup > Foot lamberts Calibration.
2. Tap Next and complete the Foot Lamberts Calibration wizard.
View the Microsoft Windows Task Manager
You use the Microsoft Windows Task Manager to view information about programs or processes 
running on your projector. The Task Manager also provides performance measures for processes.
1. Tap Menu > Service Setup > System Access.
2. Tap Task Manager.
3. Tap OK.
View the Microsoft Windows Computer
Management Console
You use the Microsoft Windows Computer Management console to manage local or remote computer 
settings.
1. Tap Menu > Service Setup > System Access. 
						

							56                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
View and Modify Projector Settings
2. Tap Computer Management.
3. Tap OK.
View Microsoft Windows Explorer
Microsoft Windows Explorer displays the hierarchical structure of files, folders, and drives on your 
projector.
1. Tap Menu > Service Setup > System Access.
2. Tap Windows Explorer.
3. Tap OK.
View the Microsoft Network Connections Window
Use the Microsoft Network Connections to view and modify network connections.
1. Tap Menu > Service Setup > System Access.
2. Tap Network Connections.
3. Tap OK.
View Projector Information
The About window provides projector information including the serial number, the current software 
version, the Digital Light Processing (DLP) version, the lens and lamp type.
Tap Menu > About.
Record the Lens Serial Number
1. Tap Menu > Advanced Setup > Lens Setup.
2. Select a lens type in the Primary Lens list.
3. Tap the Launch Dialog   icon and enter the lens serial number.
4. Tap Enter.
5. Tap Save. 
						

							CP2215 User Manual57020-101225-01 Rev. 1 (01-2014)
Manage User Accounts
User Access Permissions
This table lists the Touch Panel Controller (TPC) permissions:
Add a User Account
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > User Accounts.
2. Tap Add.
3. Tap the Launch Dialog   icon in the Username field and enter the user name.
4. Tap Enter.
5. Repeat steps 3 and 4 for the Password and Confirm Password fields.
6. Select access permissions for the user in the Permissions list.
7. Tap Accept.
Change a User Account Password or Permissions
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > User Accounts.
2. Tap a user name in the Username list.
PermissionDescription
Status Can view basic projector status, diagnostic information and software version information. 
This is the default level for Serial Communication sessions.
Operator Can activate channels and test patterns, view detailed diagnostic logs for in-depth 
troubleshooting and view server errors. This is the default level at the TPC.
Advanced Can define all display setups such as source resolution, aspect ratio, image cropping, and 
color gamut information, optimize light output, record lamp changes, and define setup files 
as selectable choices for processing a variety of incoming signals. 
Administrator Can perform screen Foot Lambert calibration, define Ethernet settings (IP network address), 
restore backup files, and upgrade the system software. NOTE: Administrators can add users 
and set user access rights from its own level and below only.
Service Can access all windows on the TPC, except marriage. 
Marriage Can access all windows on the TPC, including marriage. 
						

							58                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
Manage User Accounts
3. Tap Edit.
4. Change the password or the access permissions.
5. Tap Accept.
Delete a User Account
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > User Accounts.
2. Tap a user name in the Username list.
3. Tap Delete.
4. Tap Yes. 
						

							CP2215 User Manual59020-101225-01 Rev. 1 (01-2014)
Backup, Restore, and Upgrade
Projector Files
Add an Upgrade File
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > Upgrade.
2. Tap Upload.
3. Select the location of the upgrade file in the Drive Letter list.
4. Browse to the location of the upgrade file in the Folder list.
5. Tap the upgrade file and then tap Open.
Remove an Upgrade File
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > Upgrade.
2. Tap an upgrade file in the Available Upgrade Files list.
3. Tap Remove.
Install an Upgrade
You need Administrator or Service permissions to complete this procedure.
1. Tap Menu > Administrator Setup > Upgrade.
2. Tap an upgrade file in the Available Upgrade Files list.
3. Tap Next.
4. Tap a component in the Component list.
5. Select one of these options:
Option Description
Upgrade Different  
Components OnlyUpgrades system components that are newer or older than 
the currently installed version.
ICP Only Force Install Forces an ICP install regardless of what current version is 
installed.  
						

							60                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
Backup, Restore, and Upgrade Projector Files
6. Tap Next.
Back up Projector Settings and Information
You need Service permissions to complete this procedure.
1. Tap Menu > Service Setup > File Management.
2. Tap Backup. 
Restore a File
You need Service permissions to complete this procedure. You can restore configuration, preference, 
channel, user, and ICP files.
1. Tap Menu > Service Setup > File Management.
2. Tap Browse to the right of the File to restore field.
3. Select the location of the upgrade file in the Drive Letter list.
4. Browse to the location of the upgrade file in the Folder list.
5. Tap the upgrade file and then tap Open.
6. Select the type of file to restore in the Select type list.
7. Tap Restore.
8. Tap Yes.
Restore Factory Default Settings
You need Service permissions to complete this procedure. You can restore configuration, reference, 
channel, and user files.
1. Tap Menu > Service Setup > File Management.
2. Select a file type to restore in the Select type list.
3. Tap Reset Defaults.
4. Tap Yes.
Force Upgrade All Upgrades all components in the upgrade package.
Factory Install Removes all configurations and upgrades all components. 
Option Description 
						

							   Backup, Restore, and Upgrade Projector Files
CP2215 User Manual61020-101225-01 Rev. 1 (01-2014)
Move Files to the Projector
1. To move files from a USB Flash drive, insert the USB flash drive into the USB port on the side of 
the touch panel controller (TPC).
2. Tap Menu > Service Setup > File Maintenance.
3. Select a file type in the File Type list.
4. Tap and drag a file from the TPC Files pane to the Projector Files pane.
Delete Projector Files
1. Tap Menu > Service Setup > File Maintenance.
2. Select a file type in the File Type list.
3. Tap and drag a file from the Projector Files pane to the trash can icon.
4. Tap Yes.