Christie Digital Systems Cp2215 User Manual
Have a look at the manual Christie Digital Systems Cp2215 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 267 Christie Digital Systems manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Maintenance CP2215 User Manual83020-101225-01 Rev. 1 (01-2014) 5. Repeat steps 3 and 4 if the filter still appears dirty. 6. Shake the filter over a container until most of the water is removed. 7. Place the filter on its edge on a flat, stable surface and allow it to dry thoroughly. 8. To confirm that the filter is dry, place it over a dry paper towel and shake it. If the paper towel remains dry, the filter can be installed in the projector. 9. Record the date the filter was cleaned. 10. Replace the filter following the instructions for the specific filter. See Inspect the Card Cage Filter on page 82. Replace the Lens The lens seals the projection head, preventing contaminants from entering the main electronics area. Do not operate the projector without a lens installed. Install a lens plug when you install or transport the projector. 1. Tap and hold the red power button on the TPC Main panel to turn the lamp and projector off. 2. Allow the lamp to cool for a minimum of 15 minutes. 3. Disconnect the projector from AC power or turn the circuit breaker off. 4. Install the lens cap and turn the lens clamp to the open position. 5. If necessary, remove the 2 cap screws securing the lens to the lens mount using a hex key. 6. Pull the lens out of the lens mount and then install a small lens cap on the rear of the lens. 7. Remove the small rear cap from the new lens. Keep the front cap on. 8. Align the tabs on the lens plate with the lens mount. Insert the lens until it connects with the magnets on the mount. When the lens contacts the magnetic plates it is seated correctly. 9. Secure the lens clamp by rotating it clockwise. 10. Tighten the lens mount cap screws for added stability. 11. Remove the lens cap from the front of the lens.
CP2215 User Manual85020-101225-01 Rev. 1 (01-2014) Specifications This section provides detailed specifications for the Christie CP2215 projector. Due to continuing research, specifications are subject to change without notice. Display Panel Resolution and Refresh Rate Achievable Brightness (Measured at Screen Center) Achievable Contrast Ratio > 450:1 ANSI > 2000:1 Full Frame On/Off Color and Gray Scale ItemDescription Pixel format (H x V square pixels) 2048 x 1080 Processing path 23.97 - 240Hz LampMinimumNominalMaximum 1.4kW (CDXL-14M)5,260 lumens5,850 lumens6,500 lumens 1.6kW (CDXL-16M) 7,200 lumens8,000 lumens8,900 lumens 1.8 kW (CDXL-18SD) 9,500 lumens10,570 lumens11,750 lumens 2.0 kW (CDXL-20SD) 10,560 lumens11,740 lumens13,050 lumens 2.3kW (CDXL-23S) 12,000 lumens13,500 lumens15,000 lumens ItemDescription Displayable colors 35.2 trillion Gray Scale resolution 45 bits total linear, 15 bits per RGB component
86 CP2215 User Manual020-101225-01 Rev. 1 (01-2014) Specifications White Point Gamma Control Signal Compatibility Ethernet Port RS232-PIB ItemValue Nominal White (full white, after calibration to Color Verification mode, Theatres)x = 0.314 ± 0.006 y = 0.351 ± 0.006 ItemValue Theater (nominal) 2.6 ± 5% ItemDescription Interface 10Base-T/100-Base-TX Connector Female RJ-45 Bit Rate 10 Mbps or 100 Mbps half and full duplex ItemDescription Interface TIA-232 Connector 9-pin subminiature D, female Bit Rate 115,200 (default) bps Flow Control Hardware (RTS/CTS) Data Format 1 start bit, 8 data bits, 1 stop bit, no parity Communication Protocol Christie Serial Protocol
Specifications CP2215 User Manual87020-101225-01 Rev. 1 (01-2014) RS232-ICP GPIO Terminal SCCI Terminal ItemDescription Interface TIA-232 Connector 9-pin subminiature D, female Bit Rate 38,400 (default), 57,600, and115,200 bps (not auto- detected) Flow Control Hardware (RTS/CTS) Data Format 1 start bit, 8 data bits, 1 stop bit, no parity Communication Protocol Proprietary (see Texas Instruments specification 2509066) ItemDescription Interface Opto-LED inputs, transistor outputs Number of I/O Lines 16 – 8 inputs, 8 outputs, 1 health signal output Connector 37-pin subminiature D, female Type of Connection Opto-isolated Input Current 5mA nom., 50mA max. Input Forward Voltage Drop 1.1V nom., 1.4V max. (@ 5mA) Output current 50mA max. ItemDescription Interface Opto-LED inputs, TTL voltage output Number and type of I/O Input 1 – Lamp Off Input 2 – Lamp On Input 3 – Douser Open Input 4 – Douser Closed Output 1 – Projector Health (high = health ok) Connector 9-pin subminiature D, female Input Current 5mA nom., 50mA max. Input Forward Voltage Drop 1.1V nom., 1.4V max. (@ 5mA)
88 CP2215 User Manual020-101225-01 Rev. 1 (01-2014) Specifications 3D Terminal See 3D Sync Terminal PIN Map on page 65. USB 1 Terminal USB 2 Terminal MALM Terminal ItemDescription Interface Proprietary 3D connector Connector 15-pin subminiature D, female Bit Rate 1,200 bps Data Format 1 start bit, 8 data bits, 1 stop bit, no parity Communication Protocol RS232 and GPIO ItemDescription Interface Universal Serial Bus 2.0 Connector USB Device Standard Size (Series “A”) Maximum Bit Rate 12 Mbps Communication Protocol Texas Instruments Proprietary ItemDescription Interface Universal Serial Bus 2.0 Connector USB Device Standard Size (Series “B”) Maximum Bit Rate 12 Mbps Communication Protocol Texas Instruments Proprietary ItemDescription Interface 3.3V CMOS Connector 9-pin subminiature D, female Number of I/O Lines 4 GPIO
Specifications CP2215 User Manual89020-101225-01 Rev. 1 (01-2014) Touch Panel Controller Power Requirements AC Input (A) Below 200VAC, when the lamp is ignited, a 25 A input surge current might occur for three seconds. UPS AC Input (B) ItemDescription Type of Display Color VGA TFT LCD, backlit Display Size 144.8 mm (5.7 inches) diagonal Display Resolution (H x V pixels) 640 x 480 Maximum Dimensions (W x H x D) 195 mm x 148 mm x 58 mm Integrated Operating System Microsoft Windows ® XPe Communication Interface with Projector10/100 Base-T Ethernet Power Requirement 1.02 A max. at 24VDC ± 10% Interface Connector 12-pin Circular connector (push-pull) ItemDescription Circuit Breaker 20A Voltage Range 200 - 240 VAC Line Frequency 50 Hz - 60 Hz nominal Inrush Current
90 CP2215 User Manual020-101225-01 Rev. 1 (01-2014) Specifications Lamp The ballast is power regulated and has a maximum current of 97A. Therefore the maximum power specification for a given lamp may not be achievable until the lamp has aged, since lamp voltage increases with hours of use. Projectors typically force a 10 minute cool down period. Make sure you do not re-strike the lamp any sooner than 2 minutes into this cool down period since hot re-strikes reduce lamp life. Physical Specifications ItemDescription Type Xenon Short Arc Lamp Power (software adjustable)CXL-14M (1.4kW) 1000W min.(50%), 1430W nom., 1600W max. (110%) CDXL-18SD (1.8kW) 1000W min.(50%), 1800W nom., 1900W max. (110%) CDXL-20SD (2.0kW) 1000W min.(50%), 2000W nom., 2100W max. (110%) CDXL-23S (2.3kW) 1000W min.(50%), 2200W nom., 2300W max. (110%) Average LifeCDXL-14M - 3000 hours CDXL-18SD - 1500 hours CDXL-20SD - 1500 hours CDXL-23S - 1000 hours Wait time between lamp strikes 2 minutes minimum Warm up time to full brightness 20 minutes maximum ItemDescription Size (L x W x H) (without lens, with feet at minimum length)665 mm (26.18 inches) x 688 mm (27.08 inches) x 395 mm (15.55 inches) WeightAs installed with lens: 55 kg (121 lbs) Shipping (includes packaging) 65 kg (143 lbs) Operating PositionRotation about projection axis ± 15 degrees maximum Tilt of projection axis from horizontal ± 15 degrees maximum
Specifications CP2215 User Manual91020-101225-01 Rev. 1 (01-2014) Regulatory This product conforms to the following regulations related to product safety, environmental requirements and electromagnetic compatibility (EMC). Safety • CAN/CSA C22.2 No. 60950 • UL 60950 • IEC 60950-1 • EN60950 Electro-Magnetic Compatibility Environmental • EU Directive (2011/65/EU) on the restriction of the uses of certain hazardous substances (RoHS) in electrical and electronic equipment and the applicable official amendments) • EU Directive ( 2012/19/EU) on waste and electrical and electronic equipment (WEEE) and the applicable official amendment(s) • Regulation (EC) No. 1907/2006 concerning the Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH) and the applicable official amendment(s). • China Ministry of Information Industry Order No.39 (02/2006) on the control of pollution caused by electronic information products, hazardous substances concentration limits (SJ/T11363- 2006), and the applicable product marking requirements (SJ/T11364-2006) Certification Approvals The product is designed to comply with the rules and regulations required for the product to be sold in various regional markets, including: USA, Canada, European Union, Argentina, Australia, New Zealand, Kuwait, China, Korea, Japan, India, Mexico, Ukraine, Russia, South Africa, and Saudi Arabia. ItemDescription Emissions • FCC CFR47, Part 15, Subpart B, Class A - Unintentional Radiators • CISPR 22:EN 55022, Class A - Information Technology Equipment • ICES-3/NMB-3 (A) Immunity CISPR 24: EN55024 EMC Requirements - Information Technology Equipment
92 CP2215 User Manual020-101225-01 Rev. 1 (01-2014) Specifications Environment Operating Environment Non-Operating Environment ItemDescription Temperature 10°C to 35°C (50°F to 95°F) Humidity (non-condensing) 20% to 80% Altitude 0 - 3000 meters Maximum ambient temperature 35°C ItemDescription Temperature -25°C to 65°C (-13°F to 149°F) Humidity (non-condensing) 0% to 95%