Christie Digital Systems Cp2215 User Manual

   Troubleshooting
CP2215 User Manual73020-101225-01 Rev. 1 (01-2014)
Flicker, shadows, or dimness • Ensure the douser is open.
• Align the lamp.
• Tap Menu > Advanced Setup > LampPower/LiteLOC™ Setup. Monitor 
the Power % field to determine if the power is consistent or if it varies. 
Increase the lamp power. Lamps which are near end of service may not 
operate reliably at a lower power setting.
• Fold mirror misalignment. Contact your Christie accredited service technician 
to resolve the issue.
•...

74                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
Troubleshooting
The projector is on, but 
alternate content does not 
display• Make sure the lens cover is removed from the lens.
• Make sure the lamp is on.
• Make sure the douser is open.
• Tap   on the main TPC screen. 
• Tap Menu > Channel Setup. Verify the correct channel is selected and the...

CP2215 User Manual75020-101225-01 Rev. 1 (01-2014)
Maintenance
This section provides information and procedures for performing projector maintenance. You should 
read through this section in its entirety before performing maintenance activities. When you perform 
projector maintenance, obey all warnings and precautions.
Inspect Ventilation
Vents and louvers in the projector covers provide ventilation, both for intake and exhaust. Never 
block or cover these openings. Do not install the projector near a...

76                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
Maintenance
Clean the Radiator Filter
1. Tap and hold the red power button   on the TPC Main panel to turn the lamp and projector 
off. 
2. Allow the lamp to cool for a minimum of 15 minutes.
3.
Unplug the projector.
4. Remove the top lid.
5. Reach into the projector and then loosen the first service...

   Maintenance
CP2215 User Manual77020-101225-01 Rev. 1 (01-2014)
7. Push the clips on the top of the service panel down and out to remove the service panel.
8. Loosen the thumbscrew securing the radiator filter door.
9. Pull the filter up and out and then wash the radiator filter with water and a mild detergent or 
clean it with compressed air.
10. When the filter is completely dry, reinstall it and then install the service panel and top lid.
Inspect the Lamp
• Check the contact surfaces of the anode...

78                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
Maintenance
• For the lens only - lens cleaning solution such as Melles Griot Optics Cleaning Fluid 18LAB011 or 
equivalent
• Cotton swabs with wooden stems.
• Lens cleaning cloth or microfiber such as Melles Griot 18LAB024 or equivalent.
Clean the Lens
A small amount of dust or dirt on the lens has...

   Maintenance
CP2215 User Manual79020-101225-01 Rev. 1 (01-2014)
Remove the Existing Lamp
1. Tap and hold the red power button   on the TPC Main panel to turn the lamp and projector 
off. 
2. Allow the lamp to cool for a minimum of 15 minutes.
3.
Unplug the projector.
4. Put on your protective clothing and face shield.
5. Insert the key in the lock on the lamp door, turn the key, and then open the lamp door. Do not 
place heavy objects on the open lamp door.
6. Loosen the two thumbscrews (A and B) and...

80                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
Maintenance
g. With the lamp removed, visually inspect the reflector and clean if necessary.
8. Remove the new lamp from the protective case.
9. Loosen the cathode screw and remove the cathode nut from the lamp.
Install the New Lamp
1. Remove the tape from the ends of the protective case.
2. Remove...

   Maintenance
CP2215 User Manual81020-101225-01 Rev. 1 (01-2014)
reflector and guide the lamp onto the cathode clamp. Be careful not to hit the lamp against the 
reflector.
5. Thread on and hand-tighten the cathode nut. Make sure the smooth portion of the nut is against 
the cathode clamp.
6. Tighten the cathode clamp (F) with a hex key.
7. Align the ring terminal on the anode wire (B) with the mounting position ensuring the crimped 
side of the wire is facing out. Tighten the anode screw. 
Route anode...

82                                                                                                                                                            CP2215 User Manual020-101225-01 Rev. 1 (01-2014)
Maintenance
Inspect the Card Cage Filter
Use only high efficiency Christie approved filters. Never operate the projector without the filter 
installed.
You should check the condition of the card cage air 
filter monthly. Clean or replace the card cage air filter 
sooner if you are operating the...