Celluon Projector Picoair User Manual

Using DLNA : * To connect to a device using DLNA capability, you must install a DLNA streaming app on your mobile devie. Apps can be downloaded from  App Store / Play Store.
M/D
1. Turn on PicoAir by pressing power button and holding for 2-3 seconds.
3. Locate the mode switch next to the micro USB charge port on the side of device. Slide the switch to D to change to DLNA mode. 
1
24
2. Celluon logo will display upon powering on, followed by a Preparing wireless connection screen.4. DLNA “Ready to...

5. On a desired mobile device, go to WiFi setting, and connect to Celluon PicoAir.  Use password 12345670 to connect. 
6. When WiFi is successfully connected, open the installed DLNA streaming application  on the mobile device. 
7. Select desired content to display.
8. Select display location: Celluon PicoAir
9. Mobile device will say “Connected” and PicoAir will start projecting selected media contents.
*** For DLNA connection with iOS devices:
1. Follow above steps 1-9.
C. Switching Connection Mode -...

8. Making Adjustments
Volume Adjustment*Volume is controlled directly from PicoAir. Locate touch volume control area on top of device. Adjust the volume by lightly touching the + or – pattern.
Speaker / Earphone UsagePlease connect a speaker or an earphone to the 3.5mm audio out jack. 
Laser AlignmentWhen the images seem blurry and/or the colors appear skewed, please visit Celluon website at www.celluon.com for Laser Alignment instructions.
Engine Firmware UpdatePress and hold battery status indicator...

9. Charging the PicoAir
4-5 hours2+ hours with continuous useCharging TimeOperating Time
1. Locate micro USB port next to the battery status button. 2. Use the supplied power adapter to charge the PicoAir through    the micro USB port.
\bd  Please fully charge PicoAir’s internal battery before first use (approximately 2 to 4 hours). \bd  A low battery warning icon will show on the screen when the battery is low. \bd  Use the included power adapter to charge your PicoAir. If the battery is too low,...

10. Troubleshooting
Mobile device cannot find Celluon PicoAir during  Miracast connection searchPlease make sure PicoAir is on Miracast mode. This may also be due to particularly heavy wireless traffic. If this is the case, please reset the device by pressing the reset button on the back of device.Cannot stream contents through DLNA applicationPlease make sure device’s WiFi is properly connected to PicoAir’s WiFi. For DLNA connection, please make sure to connect using the password “12345670”
There is no...

11. Specifications
The perceived brightness of laser projectors with a given ANSI  brightness is 50%+ higher than that of the LED based projectorsBrightness
150  x 73  x 13.4 mm(6 x 3 x 0.45 inches)170 g(0.38 lbs)3140mAh @ 3.7V
SizeMeasurementWeight
The operating time may vary depending on the environment of useBattery Capacity
Product LifetimeDisplay Method
Aspect RatioThrow RatioSequential Contrast RatioDisplay Performance
ResolutionColor Depth
Operating TimeElectrical CharacteristicsSpeakerAudio...

For devices with Android OS / Mode switchFor devices with iOS / Mode switch / Application RequiredPlease use the included power adapter or any adapter supports 5V 2A to charge PicoAir. ** Using other adapters than the one provided may result in longer charging times.
0°C - 35°CYes Yes
5V / Max 2A
Operating TemperatureMiracastDLNA
MicroUSB Type
Environmental Condition
Compatibility
Power Adapter
ItemSpec.Remark
The MIT License (MIT) Copyright (c)   
Permission is hereby granted, free of charge, to any...

12. Warranty
\bd  Celluon warrants this product to be free from defects in materials and workmanship under normal use for a period of one (1) year from the date of purchase,     as evidenced by the receipt of purchase.
\bd  During the warranty period, Celluon shall repair or replace the product if defective. If replaced, the replacement shall be with a product of equal or greater value. 
\bd  This warranty is limited to the purchaser and is not transferable.
Please contact [email protected] for...

Version 1.0