Celluon Projector Picoair User Manual

							Using DLNA : * To connect to a device using DLNA capability, you must install a DLNA streaming app on your mobile devie. Apps can be downloaded from  App Store / Play Store.
M/D
1. Turn on PicoAir by pressing power button and holding for 2-3 seconds.
3. Locate the mode switch next to the micro USB charge port on the side of device. Slide the switch to D to change to DLNA mode. 
1
24
2. Celluon logo will display upon powering on, followed by a Preparing wireless connection screen.4. DLNA “Ready to Connect” screen will display upon completion of mode switch.
11 
						

							5. On a desired mobile device, go to WiFi setting, and connect to Celluon PicoAir.  Use password 12345670 to connect. 
6. When WiFi is successfully connected, open the installed DLNA streaming application  on the mobile device. 
7. Select desired content to display.
8. Select display location: Celluon PicoAir
9. Mobile device will say “Connected” and PicoAir will start projecting selected media contents.
*** For DLNA connection with iOS devices:
1. Follow above steps 1-9.
C. Switching Connection Mode - Use the sliding mode switch located next to the micro USB charge port to change connection mode.
5
12 
						

							8. Making Adjustments
Volume Adjustment*Volume is controlled directly from PicoAir. Locate touch volume control area on top of device. Adjust the volume by lightly touching the + or – pattern.
Speaker / Earphone UsagePlease connect a speaker or an earphone to the 3.5mm audio out jack. 
Laser AlignmentWhen the images seem blurry and/or the colors appear skewed, please visit Celluon website at www.celluon.com for Laser Alignment instructions.
Engine Firmware UpdatePress and hold battery status indicator for about 3 seconds. MENU screen will be displayed for menu selection. Use volume control patterns ( + & - ) to select “Firmware Update”. Follow instructions on screen to update the engine firmware.
Product Firmware UpdatePlease visit Celluon website www.celluon.com for the latest system firmware update.
13 
						

							9. Charging the PicoAir
4-5 hours2+ hours with continuous useCharging TimeOperating Time
1. Locate micro USB port next to the battery status button. 2. Use the supplied power adapter to charge the PicoAir through    the micro USB port.
\bd  Please fully charge PicoAir’s internal battery before first use (approximately 2 to 4 hours). \bd  A low battery warning icon will show on the screen when the battery is low. \bd  Use the included power adapter to charge your PicoAir. If the battery is too low, PicoAir will automatically turn off.\bd  Please use included power adapter or any adapter supports 5V 2A to charge PicoAir.** Please note that using other adapters than the one provided may result in longer charging times.
Battery Status
First three LED indicators remain solid. When charging at this stage, the next LED indicator will blink to indicate it is being charged.All four LED indicators will remain solid.100% charged
Volume control + & - sensors will blink to indicate low battery status0% chargedDescriptionStatusLED Indicator
75% charged
First two LED indicators remain solid. When charging at this stage, the next LED indicator will blink to indicate it is being charged.50% charged
First LED indicator remains solid. When charging at this stage, the next LED indicator will blink to indicate it is being charged.25% charged
14 
						

							10. Troubleshooting
Mobile device cannot find Celluon PicoAir during  Miracast connection searchPlease make sure PicoAir is on Miracast mode. This may also be due to particularly heavy wireless traffic. If this is the case, please reset the device by pressing the reset button on the back of device.Cannot stream contents through DLNA applicationPlease make sure device’s WiFi is properly connected to PicoAir’s WiFi. For DLNA connection, please make sure to connect using the password “12345670”
There is no soundPlease make sure the volume level of the PicoAir and/or connected device is not in the mute status.
Product makes abnormal noisesPlease contact Celluon Customer Service for further assistanceThe projected image is unclearThis is due to the shifts in laser diode. Please refer to Laser Alignment instruction page to adjust shifted lasers.
It takes a long time to display contents through DLNA modeIt depends on each DLNA streaming app to project contents through PicoAir. For large media files, it may take some time to load and convert the video to the correct format.PicoAir is connected, but only the black screen is projected from the devicePlease check if the connected mobile device is on sleep mode. If the screen of the connected device goes black, the projected screen will go black as well. Note that if the volume control LED patterns are on, the PicoAir is powered on.
The video stops playing periodicallyPlease make sure connected device has enough battery to play the video. If both devices have enough battery, this may be due to unstable WiFi connection. Please disconnect and reconnect the device.
Can users update PicoAir’s firmwarePlease visit Celluon website www.celluon.com for instructions to update PicoAir’s firmware.
Connection through Miracast intermittently disconnects during useThis is due to the noise occurred by double wireless connection. Try to connect again after disconnecting all the previously connected wireless networks.
Device automatically shuts down during useThis may be due to the depletion of battery or high temperature of the product. If the product is left in a place where the enviornmental temperature is high (such as in a blanket or near heater), the power will turn off automatically in protection of fire hazard. Please cool the product to specified operating temperatures before using again. If the prdouct has shut down due to battery depletion, please charge the device before turning it back on.PicoAir’s screen is frozen; it stopped playing the video / no response from buttons when pressed / cannot convert modes
Please reset the device by pressing the reset button on the back of device. Refer to “Identifying Parts” section for the location of reset button.
The occasional discrepancy between audio and visual displayWhen users stream media content from an online source while using PicoAir, audio discrepancy with video output  may occur depending  on wireless environment. The cause may be from the wireless connection between your mobile device and WiFi network or between your mobile device and PicoAir. A slight delay in mirroring (Miracast) from your mobile device to PicoAir may also occur.
PicoAir turns off while chargingPlease make sure PicoAir is being charged with the dedicated adapter. Other  adapters may not meet the optimal  power supply required for PicoAir. Therefore, using other adapters than the one provided may lead to the PicoAir turning off until sufficient battery power is stored.15 
						

							11. Specifications
The perceived brightness of laser projectors with a given ANSI  brightness is 50%+ higher than that of the LED based projectorsBrightness
150  x 73  x 13.4 mm(6 x 3 x 0.45 inches)170 g(0.38 lbs)3140mAh @ 3.7V
SizeMeasurementWeight
The operating time may vary depending on the environment of useBattery Capacity
Product LifetimeDisplay Method
Aspect RatioThrow RatioSequential Contrast RatioDisplay Performance
ResolutionColor Depth
Operating TimeElectrical CharacteristicsSpeakerAudio Interface
Classification
Laser Safety
FocusMax. Image (Screen) Size
32 ANSI Lumens
Laser10,000 hours
16:91.380,000 : 11920 x 720pHD resolution16.7M color (RGB 24bit)
Apprx. 2+ hrs1.0W3.5mm ear phone jackWirelessDual (2.4, 5G)IEC-60825-1 Class 3RConsumer safe deviceOutputWavelength Divergence AnglePulse Frequency60Hz
Red 90mW / Blue 85mW / Green 50mWRed 639nm / Blue 445nm / Green 522nm42.1 deg
Focus Free (always in focus)No focus wheel required250 inchesIn optimal lighting conditions
Laser Spec
ItemSpec.Remark
16 
						

							For devices with Android OS / Mode switchFor devices with iOS / Mode switch / Application RequiredPlease use the included power adapter or any adapter supports 5V 2A to charge PicoAir. ** Using other adapters than the one provided may result in longer charging times.
0°C - 35°CYes Yes
5V / Max 2A
Operating TemperatureMiracastDLNA
MicroUSB Type
Environmental Condition
Compatibility
Power Adapter
ItemSpec.Remark
The MIT License (MIT) Copyright (c)   
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the Software), to deal in the Software  without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF  MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
17 
						

							12. Warranty
\bd  Celluon warrants this product to be free from defects in materials and workmanship under normal use for a period of one (1) year from the date of purchase,     as evidenced by the receipt of purchase.
\bd  During the warranty period, Celluon shall repair or replace the product if defective. If replaced, the replacement shall be with a product of equal or greater value. 
\bd  This warranty is limited to the purchaser and is not transferable.
Please contact [email protected] for warranty supports.
18 
						

							Version 1.0