Casio Qt 6100 Service Manual

							
— 29 —
  No    Device to be checked  Operation   Note  Page
  1  Batch test 1    2  Test Device : RAM, FLASH, Display,   32
         Print, Time, Drawer  
  2  Batch test 2    3   Test Device : Display, Back light  32
  3  RAM WRITE/READ test n011    33
  4  RAM READ only test  n111    33
  5  FLASH Check SUM test  n512    34
  6 FLASH CLEAR/WRITE/READ test  n612     34
  7  CF-CARD WRITE/READ test  pn013     35
  8  CF-CARD READ only test  pn113     35
  9  CF-CARD CLEAR test  pn213    36
  10 CF-CARD CLEAR&WRITE/READ test pn313     36
  11  LCD test    n021    37
  12  LCD calibration test  221    38
  13  Back light OFF test  121    38
  14  Remote Cust DISP test  bn023    39
  15  External printer print test  x1x2x3n03d     40
  16  RS232C PORT test  xn04d    41
  17  RS232C PORT batch test  40    42
  18  Ethernet test    m0a51    43
  19  MAC Address SET  x0951    44
  20  Time setting   x1x2x3x4x5x60a70     46
  21  Time display    70    46
  22  Drawer open test  xn091    46
  23  Buzzer test    n092    47
  24  OBR test    95    47
  25  MCR test    96    48
  26  Charging test    99    50
7-5. Check item
   The following test can be checked in the diagnostic test. 
						

							
— 30 —
7-6. Operation of each test 
[ 1 ] Batch test 1
[Function]
  RAM  test,  FLASH  test,  display  test,  test  print,  time  setting  and  drawer  open  test  are  performed 
continuously.
  Make sure to connect the printer to COM1.
[Operation]
Refer to the page for the details of the following tests.
  Operation :  2  ST
The following tests are performed automatically.
(1)  RAM test : WRITE/READ all block test
(2)  FLASH : Check SUM test
(3)  Test print
(4)  Times setting : Set the following data.
      Arranged data : 2001 December 31, 23:59’30
(5)  Drawer open : Opens all drawer.
    Enters the wait mode for the input of [OK] or [NG] by the operator after drawer open.
(6)  Receipt issuance
[LCD]
*When normally printed
BATC H    2  
RAM WR    OK
FLASH CHK SUM  OK
 
BBBBBBBBBBBBBBBBBBBB     
             *8,888,88
DA TE   01/12/31 
TIME 
  23:59-30  
DRW ALL    OK 
END   
2  Print 
T
est
[Print]
*When normally printed
BA TC H    2  
RAM WR    OK
 
FLASH CHK SUM  OK
DATE   01/12/31 
TIME 
  23:59-30 
Please Hit Key  OK->1  NG->9  
DRW ALL    OK 
END   
2 
[Print]
*When normally printed
[ 2 ] Batch test 2
[Function]
  LCD display test and backlight test are performed continuously.
[Operation]
Refer to the page for the details of the following tests.
  Operation :  3  ST
The following tests are performed automatically.
(1)  LCD test : 
    Enters the wait mode for the input of [OK] or [NG] by the operator after the test.
    "OK" = 1, "NG" = 9
(2)  Backlight OFF test : 
      Turns the backlight off.
      Enters the wait mode for the input of [OK] or [NG] by the operator after the backlight turns off.
      *Since the backlight is turned off, "Please Hit Key..." cannot be seen.
   "OK" = 1, "NG" = 9
(3)  Receipt issuance
[LCD]
*When normally printed
BA TCH    3  
Please Hit Key  OK->1  NG->9 
LCD   OK
Please Hit Key  OK->1  NG->9  
BACK LIGHT  OK 
END   
3  Waiting for the input of [OK] o
r
[NG] for the LCD test.
Waiting for the input of [OK] or
[NG] for the backlight.
* When this appears, the backlight
is turned o ff
.
BATC H    3  
LCD   OK 
BACK LIGHT  OK 
END   
3  
						

							
— 31 —
[ 3 ] RAM WRITE/READ test
[Function]
  WRITE/READ test for RAM is performed.
  A counter is displayed for RAM test as follows.
[Operation]
  Operation :  n  0  1  1  ST
n:  01 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
RAM    n011 
RAM WR       OK 
END   
n011
[PRINT]
NOTE:  Prints the address of the error in case the test ended 
with an error.
Prints the address of the error in case the test ended with an 
error.
RAM  n011
RAM WR       N
G
END   
n011
[ 4 ] RAM READ ONLY test
[Function]
  READ ONLY test for RAM is performed
  Note that WRITE test (n011) must be performed right before this test.
[Operation]
  Operation :  n  1  1  1  ST
n:  01 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
RAM    n111 
RAM RD       OK 
END   
n111
RAM    n111
RAM RD       O
K
END   
n111
NOTE:  Prints the address of the error in case the test ended 
with an error.
Prints the address of the error in case the test ended with an 
error.
[PRINT] 
						

							
— 32 —
[ 5 ] FLASH Check SUM test
[Function]
  This test will check SUM test for FLASH is performed.
[Operation]
  Operation :  n  5  1  2  ST
n:  01 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
[PRINT]
FLASH  512
FLASH CHK SUM  OK
 
END   
512
FLASH  512
FLASH CHK SUM  OK
END   
512
[ 6 ] FLASH CLEAR WRITE/READ test
[Function]
  The CLEAR & WRITE/READ test for FLASH is performed.
  After deleting the memory by CLEAR, WRITE/READ test is performed.
  Note: since this test cannot backup the program, you need to perform IPL again after the test. 
When the memory in the FLASH memory is cleared (by the CLEAR test), the program is 
cleared also. 
[Operation]
  Operation :  n  6  1  2  ST
n:  01 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
NG  and  the  address  are  displayed  if  WRITE  cannot  be  done 
normally.
NG  and  the  address  are  printed  if  WRITE  cannot  be  done 
normally.
[PRINT]
FLASH     612
FLASH WR ERASE PGM  OK
 
END     
612
FLASH    612
FLASH WR ERASE PGM  OK
 
END     
612 
						

							
— 33 —
[ 7 ] CF-CARD WRITE/READ test
[Function]
  This test will check the write/read test (connection test) for CF-CARD.
  Perform the CF-CARD clear test, before start of this test.
  Note that this test does not ensure the data inside the CF-CARD as well as its performance.
[Operation]
  Operation :  p  n  0  1  3  ST
p :  designates PCMCIA SLOT
  0 = CF
  1 = PCMCIA
n:  0 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
NG  and  the  address  are  displayed  if  WRITE  cannot  be  done 
normally.
[PRINT]
CF-CARD  pn013
CF WR    OK 
END   
pn013
CF   pn013
CF WR    OK 
END   
pn013
NG  and  the  address  are  printed  if  WRITE  cannot  be  done 
normally.
[ 8 ] CF-CARD READ ONLY test
[Function]
  This test will check the read only test for CF-CARD.
  Perform the CF-CARD write test, before start of this test.
  Note that this test does not ensure the data inside the CF-CARD as well as its performance.
[Operation]
  Operation :  p  n  1  1  3  ST
p:  designates PCMCIA SLOT
  0 = CF
  1 = PCMCIA
n:  0 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
NG  and  the  address  are  displayed  if  READ  cannot  be  done 
normally.
NG  and  the  address  are  printed  if  WRITE  cannot  be  done 
normally.
CF-CARD  pn1 13
CF RD    OK 
END   
pn1 13
CF-CARD  pn113
CF RD    OK 
END   
pn1 13
[PRINT] 
						

							
— 34 —
[ 9 ] CF-CARD CLEAR test
[Function]
  This test will check the clear test for CF-CARD.
  Note that this test does not ensure the data inside the CF-CARD as well as its performance.
[Operation]
  Operation :  p  n  2  1  3  ST
p:  designates PCMCIA SLOT
  0 = CF
  1 = PCMCIA
n:  0 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
NG and the address are displayed if CLEAR cannot be done 
normally.
NG  and  the  address  are  printed  if  WRITE  cannot  be  done 
normally.
CF-CARD  pn213
CF CLR    OK 
END   
pn213
CF-CARD  pn213
CF CLR    OK 
END   
pn213
[PRINT]
[ 10 ] CF-CARD CLEAR WRITE/READ test
[Function]
  The CLEAR & WRITE/READ test for CF-CARD is performed.
  After deleting the memory by CLEAR, WRITE/READ test (connection test) is performed.
  Note that this test does not ensure the data inside the CF-CARD as well as its performance.
[Operation]
  Operation :  p  n  3  1  3  ST
p:  designates PCMCIA SLOT
  0 = CF
  1 = PCMCIA
n:  0 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
NG  and  the  address  are  displayed  if  WRITE  cannot  be  done 
normally.
[PRINT]
CF-CARD  pn313
CF CLR&WR  OK
 
END   
pn313
CF-CARD  pn313
CF CLR&WR  OK
 
END   
pn313
NG  and  the  address  are  printed  if  WRITE  cannot  be  done 
normally. 
						

							
— 35 —
[ 11 ] LCD test
[Function]
  This test will check the LCD display.
  In case of one time check only, the test can be ended by the judgment (OK or NG) of the opera-
tor.
  The  display  can  be  switched  by  the  touch  of  the  panel. The  display  will  not  change  to  the  next 
one unless the panel is touched.
[Operation]
  Press [OK] key or [NG] key to end the test when performing one time check.
 "OK" = 1, "NG" = 9
  Operation :   n  0  2  1  ST
n:  0 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
[LCD]
GreenBlueReverse 
checkRedWhiteBlackTo
uch any placein the panel. Touch any place
in the panel. Touch any placein the panel.Touch any place
in the panel.Touch any placein the panel.Touch any placein the panel.
Check (blackand white)    
  Shows  the  following  colors  and  patterns  in  the  display  in  the  order  of  black,  white,  red,  green, 
blue, check and reverse check.
  Returns to the normal display after the test, and waits for the input of [OK] or [NG] by the operator (in 
case of one time check).
  In case of continuous check, the test is ended manually upon the input of [ESC] key.
LCD  n021
LCD 
  OK 
END   
n021
[PRINT]
LCD  n021
LCD    OK 
END   
n021 
						

							
— 36 —
[ 13 ] LCD Backlight OFF test
[Function]
  This is a test for the LCD backlight.
  The test ends upon judgment of the operator between [OK] and [NG].
[Operation]
  Press [OK] key or [NG] key to end the test when performing one time check.
  "OK" = 1, "NG" = 9
  Operation :  1  2  1  ST
[LCD]
[PRINT]
BACK LIGHT 121
BACK LIGHT  OK 
END   
121
BACK LIGHT 121
BACK LIGHT  OK 
END   
121
[ 12 ] LCD calibration test
[Function]
  This will test the calibration of the LCD (touch panel).
  * Perform  the  calibration  in  the  diagnostic  mode  even  when  the  product  is  in  the  market.  Make 
sure to backup the register data when necessary.
[Operation]
  A  cross  appears  at  the  following  four  coordinates  in  the  panel  one  by  one.  When  a  cross  at  a 
certain coordinate is touched, the next coordinate will show another cross there.
  (X,Y) = (100,100), (100,500), (700,100), (700,500)
  Operation :   2  2  1  ST
[LCD]
T OUCH ST ART 221
(X1,Y1)  : (XXX,XXX)
(X2,Y2)  : (XXX,XXX)
(X3,Y3)  : (XXX,XXX)
(X4,Y4)  : (XXX,XXX)
END   
 221
[PRINT]
T OUCH ST ART 221
(X1,Y1)  : (XXX,XXX)
(X2,Y2)  : (XXX,XXX)
(X3,Y3)  : (XXX,XXX)
(X4,Y4)  : (XXX,XXX)
END   
 221
Displays data 1 for calibration
Displays data 2 for calibration
Displays data 3 for calibration
Displays  the  position  of  the  forth  coordinate  (performs  cali-
bration) 
						

							
— 37 —
[ 14 ] Remote Cust DISP test
[Function]
  This test will check whether REMOTE DISP can be displayed.
  Make sure to connect REMOTE DISP to COM3.
  In case of one time check only, the test can be ended by the judgment (OK or NG) of the opera-
tor.
  Pastel  green  (white  plus  green)  appears  as  the  backlight,  which  turns  off  upon  the  end  of  the 
test.
  * When changing the baud rate, make sure to change the REMOTE DISP setting.
[Operation]
  Press [OK] key or [NG] key to end the test when performing one time check.
 "OK" = 1, "NG" = 9
  Operation :  b  n  0  2  3  ST
b:  Baud rate selection
0 = 19.2 Kbps, 1 = 9600 bps
n:  0 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
  When  performing  continuous  check,  the  same  test  character  data  is  sent  at  a  certain  interval. 
When  the  test  is  ended  manually  upon  the  input  of  [ESC]  key,  the  display  is  cleared  and  the 
backlight turns off.
  In case of one time check, the display is cleared and the backlight turns off after the judgment ([OK] 
or [NG]) of the operator.
[LCD]
REMOTE DISP na23
REMOTE DISP  OK 
END   
na23
REMOTE DISP na23
REMOTE DISP  OK 
END   
na23
[REMOTE DISP]
ABCDEFGHIJKLMNOP QRSTUVWXYZabcdef
0,1,2,3,4,5,6,7,8,9,
[PRINT] 
						

							
— 38 —
[ 15 ] External printer print test
[Function]
  This test will check the print test for the RS232C I/F printer.
  Connect the printer to the COM which is to be tested.
[Operation]
  Operation :   x1  x2  x3  n  0  3  d  ST
X1: Print test pattern (0 = A pattern, 1 = B pattern)
X2: Port selection (1 = COM1, 2 = COM2, 3 = COM3)
X3: Baud rate selection (1 = 4800 bps, 2 = 9600 bps, 3 = 19.2 kbps)
n:  0 = One time check (can be omitted)
  not 0 = Continuous check (To stop the test, press "ESC" key)
d:  Printer type selection (1 = RJ, 2 = SLIP)
  Note that some printers cannot use certain baud rates. Refer to the list below.
  When changing the baud rate, make sure to change the setting for the printer also.
A patternB pattern
19.2 Kbps 9600 bps 4800 bps
SLIP PRINTER (SP1300)
RJ PRINTER (UP250/350/360)
BBBBBBBBBBBBBBBBBBBBB            *8,888,88BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
[LCD]
PR T   xxxn03d
END    xxxn03d
Error display
When the printer is not connected
NON PRINTER ERR
[PRINT]
Printing pattern is the following 2 types.
The number of lines : 40 lines for RJ and 35 lines for SLIP.