Casio Projector XJ-A130 User Manual

21
The password feature lets you keep unauthorized individuals from using the projector. You can specify 
whether password input is required whenever you turn on the projector, and you can specify and 
change the password as required. Use the setup menu “Option Settings 1 Power On Password” 
setting to configure power on password settings.
Inputting a Password
The password of your projector is not really a “word” made up of letters, but rather a sequence of 
remote controller key inputs. The following...

22
Keep a written record of your password!
You will not be able to use the projector if you forget its password. We strongly suggest that you keep 
a written or other type of record of the password so you can look it up when necessary.
To change the password
1.Press the [MENU] key to display the setup menu.
2.Use the [] key to select “Option Settings 1”, and then press the [ENTER] key.
3.Use the [] key to select “Power On Password”, and then press the [ENTER] 
key.
This will display a dialog box...

23
To turn password protection on and off
1.Display the Power On Password setting screen by performing steps 1 through 5 
of the procedure under “To change the password” on page 22.
At this time, make sure that “Power On Password” is selected on the Power On Password 
setting screen.
2.Use the [] and [] keys to select “On” or “Off”.
Changing the power on password setting from “Off” to “On” causes the confirmation dialog 
box shown below to appear.
Press the [ENTER] key to confirm that you want to...

24
You can use the procedures in this section to restore all of the settings on a particular main menu or all 
of the settings on the setup menu to their initial factory defaults.
To restore all settings on a particular main menu to their initial factory 
defaults
1.Press the [MENU] key to display the setup menu.
2.Use the [] and [] keys to select the main menu whose settings you want to 
restore to their initial factory defaults.
You can select Image Adjustment 1, Image Adjustment 2, Volume...

25
To restore all settings on the setup menu to their initial factory defaults
1.Press the [MENU] key to display the setup menu.
2.Use the [] key to select “Restore All Defaults” and then press the [ENTER] key.
3.After confirming that “Restore All Defaults” sub-menu is selected, press the 
[ENTER] key.
This displays a confirmation message asking if you want to initialize all settings.
4.Use the [] key to select “Yes”.
5.To restore all settings on the setup menu to their initial defaults, press the...

26
This section contains tables that provide detailed explanations of all of the items included on the setup 
menu. The following describes the type of information that appears in each of the columns of the 
tables.
Image Adjustment 1 Main Menu
Setup Menu Contents
Setting Name: This column shows the names of the settings as they appear on the sub-menu.
Input: This column shows the input source for which each setting is supported.
Input source names are abbreviated as follows:
R : RGB input
C  : component...

27
Color ModeRCVHDWUSource 
SpecificYou can select from among four different color mode settings to 
optimize the projected image in accordance with image contents 
and projection conditions.
Standard:
Use this setting when you want to highlight the colors of your 
presentation.
Graphics:
Use this setting when you want photographs and graphics to 
appear natural.
Theater:
Use this setting to bring out the dark portions of your images.
Blackboard:
Use this setting for easy viewing when projecting onto a...

28
Image Adjustment 2 Main Menu
About the “Signal Specific” Setting Unit
For the items that have “Signal Specific” in the “Setting Unit” column of the above table, the setting is 
saved for the specific type of signal (XGA/60Hz, SXGA/60Hz, etc.) that is being input when the setting 
is performed, and not for a specific input source.
Volume Adjustment Main Menu
Setting NameInputSetting UnitDescription
Vertical 
Position
RCVSignal 
SpecificUse this sub-menu to adjust the vertical position of the input...

29
Screen Settings Main Menu
Setting NameInputSetting UnitDescription
Keystone 
Correction
RCVHDWUNSingle Use this sub-menu to correct vertical keystoning of the projected 
image.
Aspect Ratio
RCVHDSource 
SpecificUse this sub-menu to select an aspect ratio setting for the 
projected image.
Input Source: RGB or HDMI (PC)Normal*:
Projects at the projector’s maximum possible size while 
maintaining the input signal aspect ratio.
Full:
Projects at the projector’s maximum possible size by enlarging 
or...

30
Projection 
ModeRCVHDWUNSingle Use this sub-menu to specify whether projection will be from the 
front of the screen or the back of the screen.
Front*:
Select this option to project from the front of the screen.
Rear:
Select this option to project from the back of the screen. This 
setting flips the front projected image horizontally.
Ceiling Mount
RCVHDWUNSingle Use this sub-menu to configure the projector for use in an 
installation in which it is positioned upside down.
On:
Flips the projected...