Casio Projector XJ-A130 User Manual

11
Momentarily Cutting Off the Input Source Image
1.Press the [BLANK] key.
This temporarily cuts off the image from the input source and projects a black screen in its 
place.
2.To resume projection of the image from the input source, press the [BLANK] key 
(or [ESC] key).
NoteYou can specify projection of a black screen or blue screen, or a logo. For details, see “Blank 
Screen” under “Screen Settings Main Menu” on page 30.
Freezing an Image
Pressing the [FREEZE] key freezes the projected image.
To...

12
Displaying a Pointer in the Projected Image
You can select from among different pointer styles, including various arrow styles, for display in the 
projected image. Pointers can be used during a presentation to indicate or highlight a specific part of 
the image.
NoteDepending on the pointer style you are using, the pointer may not display properly when you are 
using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE …] keys to 
change the keystone correction value to zero.
To...

13
Changing the aspect ratio of the projected image
Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.
Available settings depend on your projector model as shown below. For details about the meaning of 
each setting, see the “Aspect Ratio” setting (page 29) on the “Screen Settings Main Menu”.
XJ-A230/XJ-A235/XJ-A240/XJ-A245
Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as 
shown below....

14
You can use the remote controller keys to adjust the volume level of the audio that is output from the 
projector’s speaker.
To adjust the volume level
1.Press the [VOLUME] key.
This causes the [Volume] screen to appear on the projected image.
2.Press the [] key to increase the volume, or the [] key to lower the volume.
3.After the setting is the way you want, press the [ESC] key.
This causes the [Volume] screen to disappear.
NoteYou also can use the setup menu to adjust the volume level. For...

15
The following three Eco Mode settings are available to specify whether priority should be given to 
low-power, low-noise operation or lamp brightness.
Changing the Eco Mode Setting
1.Press the [ECO] key.
This displays the Eco Mode selection window. The currently selected Eco Mode is the one 
whose button is selected (filled in).
2.Use the [] and [] keys to move the highlighting to the Eco Mode you want to 
select, and then press the [ENTER] key.
This will select the button next to the highlighted...

16
Pressing the [FUNC] key displays the menu shown below.
You can use this menu to perform the operations described below.
Adjust image brightness
Highlight “Brightness” and then press the [ENTER] key.
Turn the Eco Mode on or off
Highlight “Eco Mode” and then press the [ENTER] key.
Select the aspect ratio of the projected image
Highlight “Aspect Ratio” and then press the [ENTER] key.
Note(for USB port model users)
When the input source is an external device connected to the USB port or via the...

17
Configuring Advanced Projector Settings
Your projector has a setup menu that you can use to configure advanced settings.
Displaying the Setup Menu
Pressing the [MENU] key displays the menu shown below in the center of the projection screen.
To exit the setup menu
Press the [MENU] key.
Configuring Setup Menu Settings
1.Press the [MENU] key to display the setup menu.
2.Use the [] and [] keys to select the main menu item you want by highlighting 
it.
3.Press the [ENTER] key.
4.Use the [] and [] keys...

18
Basic Setup Menu Example
The procedure below shows how to configure the following three settings:
Image Adjustment 1  Contrast
Image Adjustment 1  Color Mode
Input Settings  Signal Name Indicator
NoteCertain settings on the setup menu cannot be changed while there is no input signal to the 
projector. Because of this, you should configure setup menu settings after selecting an input 
source and starting projection.
This example covers basic steps only. For more detailed information, see “Setup...

19
To configure the “Image Adjustment 1  Color Mode” setting
5.Use the [] key to select “Color Mode”.
6.Press the [ENTER] key.
This displays the color mode menu.
7.Use the [] and [] keys to select the color mode you want, and then press the 
[ENTER] key.
8.After selecting the color mode you want, press the [ESC] key.
To configure the “Input Settings  Signal Name Indicator” setting
9.Press the [ESC] key.
10.Use the [] key to select “Input Settings”.
11.Press the [ENTER] key.
12.Use the [] key to...

20
Direct Power On
You can configure the projector so it powers up automatically as soon as you plug it into a power 
source. With this “Direct Power On” feature, you do not even need to press the [P] (Power) key. To 
enable Direct Power On, display the Setup Menu, and then change the “Direct Power On” setting to 
“On”.
Important!When you have Direct Power On enabled, do not leave the projector plugged into an electrical 
outlet while it is turned off. If you do, there is the chance that it (and the...