Casio Projector XJ-A130 User Manual

							11
Momentarily Cutting Off the Input Source Image
1.Press the [BLANK] key.
This temporarily cuts off the image from the input source and projects a black screen in its 
place.
2.To resume projection of the image from the input source, press the [BLANK] key 
(or [ESC] key).
NoteYou can specify projection of a black screen or blue screen, or a logo. For details, see “Blank 
Screen” under “Screen Settings Main Menu” on page 30.
Freezing an Image
Pressing the [FREEZE] key freezes the projected image.
To freeze the projected image
1.While an image is being projected from an input source, press the [FREEZE] key.
This will capture the image that is on the screen at the moment you press [FREEZE] and stores 
it in projector memory. That image remains projected on the screen.
2.To restore projection of the image from an input source, press the [ESC] key. 
						

							12
Displaying a Pointer in the Projected Image
You can select from among different pointer styles, including various arrow styles, for display in the 
projected image. Pointers can be used during a presentation to indicate or highlight a specific part of 
the image.
NoteDepending on the pointer style you are using, the pointer may not display properly when you are 
using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE …] keys to 
change the keystone correction value to zero.
To display a pointer in the image
1.Press the [POINTER] key.
This will cause a pointer to appear in the image.
You also can use the setup menu to specify the pointer type that appears first when you press 
the [POINTER] key. For details, see “Pointer” under “Option Settings 2 Main Menu” on 
page 33.
2.Use the cursor keys to move the pointer to the location you want.
Holding down a cursor key moves the cursor at high speed.
3.To modify the pointer as described below, press the [STYLE] key.
To select the pointer type
1.Press the [POINTER] key to display the pointer.
2.Keep pressing the [POINTER] key until the pointer you want is displayed.
Each press of the [POINTER] key cycles through the available pointer types.
To clear the pointer from the image
Press the [ESC] key.
For this pointer type:Pressing [STYLE] will change it like this:
  
            
  
            
  
            
  
            
Toggle between flashing and not flashing 
						

							13
Changing the aspect ratio of the projected image
Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.
Available settings depend on your projector model as shown below. For details about the meaning of 
each setting, see the “Aspect Ratio” setting (page 29) on the “Screen Settings Main Menu”.
XJ-A230/XJ-A235/XJ-A240/XJ-A245
Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as 
shown below.
XJ-A130/XJ-A135/XJ-A140/XJ-A145
Pressing the [ASPECT] key will toggle between settings in accordance with the current input source as 
shown below.
NoteWhen the input source is a component or an HDMI (DTV) signal with an aspect ratio of 16:9, 
the aspect ratio is fixed at 16:9. In this case, pressing the [ASPECT] key will not change the 
aspect ratio setting.
For details about how the aspect ratio setting affects the projected image, see “Aspect Ratio 
Setting and Projection Image” (page 44).
You also can change the aspect ratio setting using the setup menu. For details, see “Aspect 
Ratio” under “Screen Settings Main Menu” on page 29.
Important!Note that enlarging or reducing the size of an image using the [ASPECT] key for commercial 
purposes or public presentation may infringe on the legally protected copyright of the copyright 
holder of the original material.
Input SourcePressing [ASPECT] will cycle through these settings:
VIDEO, Component, HDMI (DTV) Normal  16:9  Letter Box
RGB, HDMI (PC) Normal  Full  True
Input SourcePressing [ASPECT] will toggle between these settings:
VIDEO, Component, HDMI (DTV) Normal 
 16:9
RGB, HDMI (PC) Normal 
 Full 
						

							14
You can use the remote controller keys to adjust the volume level of the audio that is output from the 
projector’s speaker.
To adjust the volume level
1.Press the [VOLUME] key.
This causes the [Volume] screen to appear on the projected image.
2.Press the [] key to increase the volume, or the [] key to lower the volume.
3.After the setting is the way you want, press the [ESC] key.
This causes the [Volume] screen to disappear.
NoteYou also can use the setup menu to adjust the volume level. For details, see “Volume 
Adjustment Main Menu” on page 28.
To mute the audio
1.Press the [VOLUME] key.
2.Press the [ENTER] key.
This stops output from the speaker.
3.To restore the audio, press the [VOLUME] key again.
Adjusting the Volume Level 
						

							15
The following three Eco Mode settings are available to specify whether priority should be given to 
low-power, low-noise operation or lamp brightness.
Changing the Eco Mode Setting
1.Press the [ECO] key.
This displays the Eco Mode selection window. The currently selected Eco Mode is the one 
whose button is selected (filled in).
2.Use the [] and [] keys to move the highlighting to the Eco Mode you want to 
select, and then press the [ENTER] key.
This will select the button next to the highlighted Eco Mode name.
3.To hide the window, press the [ESC] key.
Note(for USB port model users)
Use the setup menu (page 17) to select the Eco Mode when the input source is an external 
device connected to the USB port or via the wireless adapter.
Eco Mode (Power Saving, Low Noise)
On (Level2) :  Gives maximum priority to low-power, low-noise operation.
On (Level1) :  Provides low-power, low-noise operation while maintaining lamp brightness to some 
level.
Off : Gives maximum priority to lamp brightness. 
						

							16
Pressing the [FUNC] key displays the menu shown below.
You can use this menu to perform the operations described below.
Adjust image brightness
Highlight “Brightness” and then press the [ENTER] key.
Turn the Eco Mode on or off
Highlight “Eco Mode” and then press the [ENTER] key.
Select the aspect ratio of the projected image
Highlight “Aspect Ratio” and then press the [ENTER] key.
Note(for USB port model users)
When the input source is an external device connected to the USB port or via the wireless 
adapter, use the [FUNC], [O], [
f], and [Z] keys to control the connected device. For details, 
see the “USB Function Guide” and “Wireless Function Guide” on the bundled CD-ROM.
Using the [FUNC] Key
  This performs the same operation as pressing the [BRIGHT] key (O key) described on page 9.
  This performs the same operation as pressing the [ECO] key (
f key) described on page 15.
  This performs the same operation as pressing the [ASPECT] key (
Z key) described on page 13. 
						

							17
Configuring Advanced Projector Settings
Your projector has a setup menu that you can use to configure advanced settings.
Displaying the Setup Menu
Pressing the [MENU] key displays the menu shown below in the center of the projection screen.
To exit the setup menu
Press the [MENU] key.
Configuring Setup Menu Settings
1.Press the [MENU] key to display the setup menu.
2.Use the [] and [] keys to select the main menu item you want by highlighting 
it.
3.Press the [ENTER] key.
4.Use the [] and [] keys to select the sub-menu item you want by highlighting it.
5.Perform the required operation on the selected sub-menu item screen.
The guidance text explains the operations you need to perform to configure each setting.
6.To return to the main menu from the sub-menu, press the [ESC] key.
7.To exit the setup menu, press the [MENU] key.
Basic Setup Menu Operations
Main menu
Pressing the [MENU] key displays the main menu. 
The currently selected menu item is the one that is 
highlighted.
Sub-menu
The sub-menu shows each individual setting under each 
main menu item, and its current setting.
Guidance text
Guidance text provides a brief description of the main 
key operations available for the operation you are 
currently performing. 
						

							18
Basic Setup Menu Example
The procedure below shows how to configure the following three settings:
Image Adjustment 1  Contrast
Image Adjustment 1  Color Mode
Input Settings  Signal Name Indicator
NoteCertain settings on the setup menu cannot be changed while there is no input signal to the 
projector. Because of this, you should configure setup menu settings after selecting an input 
source and starting projection.
This example covers basic steps only. For more detailed information, see “Setup Menu 
Contents” on page 26.
To configure the “Image Adjustment 1  Contrast” setting
1.Press the [MENU] key to display the setup menu.
2.“Image Adjustment 1” is initially selected on the main menu, so simply press the 
[ENTER] key.
3.Use the [] key to select “Contrast”.
4.Use the [] (lighter) and [] (darker) keys to adjust contrast. 
						

							19
To configure the “Image Adjustment 1  Color Mode” setting
5.Use the [] key to select “Color Mode”.
6.Press the [ENTER] key.
This displays the color mode menu.
7.Use the [] and [] keys to select the color mode you want, and then press the 
[ENTER] key.
8.After selecting the color mode you want, press the [ESC] key.
To configure the “Input Settings  Signal Name Indicator” setting
9.Press the [ESC] key.
10.Use the [] key to select “Input Settings”.
11.Press the [ENTER] key.
12.Use the [] key to select “Signal Name Indicator”.
13.Use the [] and [] keys to select “On” or “Off”.
14.After you are finished, press the [MENU] key to exit the setup menu. 
						

							20
Direct Power On
You can configure the projector so it powers up automatically as soon as you plug it into a power 
source. With this “Direct Power On” feature, you do not even need to press the [P] (Power) key. To 
enable Direct Power On, display the Setup Menu, and then change the “Direct Power On” setting to 
“On”.
Important!When you have Direct Power On enabled, do not leave the projector plugged into an electrical 
outlet while it is turned off. If you do, there is the chance that it (and the lamp) might turn on 
automatically when power is restored after being cut off by a power outage, tripping of a 
breaker, etc.
NoteDirect Power On causes the projector to turn on automatically as soon as it is plugged into a 
power outlet. This greatly reduces the amount of time it takes until you are ready to start 
projecting. Note, however, that the actual startup sequence (Standby State Power On 
Projection Starts) that the projector performs is the same, regardless of whether Direct Power 
On is enabled or disabled. The only difference is what triggers the sequence (plugging in or 
pressing the [P] (Power) key). For details about the startup sequence that the projector 
performs when you plug it into a power source, see “To turn on the projector” in the separate 
“User’s Guide (Basic Operations)”.
For details about configuring the Direct Power On setting, see “Direct Power On” under 
“Option Settings 1 Main Menu” on page 32.