Casio Projector XJ-A130 User Manual

							21
The password feature lets you keep unauthorized individuals from using the projector. You can specify 
whether password input is required whenever you turn on the projector, and you can specify and 
change the password as required. Use the setup menu “Option Settings 1 Power On Password” 
setting to configure power on password settings.
Inputting a Password
The password of your projector is not really a “word” made up of letters, but rather a sequence of 
remote controller key inputs. The following is the 8-key sequence that represents the initial factory 
default password.
Using the Password Feature
Note the following precautions whenever you use the password feature.
The password feature protects against unauthorized use of the projector. Note that it is not an anti-
theft measure.
You will need to enter the initial factory default password the first time you use the projector after 
turning on the password feature. Change the initial factory default password to a different one of 
your choice as soon as possible after turning on the password feature.
Remember that password operations are always performed using the remote controller, so you 
should take care not to lose or misplace the remote controller.
Also note that you will not be able to input the password if the remote controller batteries are dead. 
Replace the remote control batteries as soon as possible after it starts to go low.
If you forget your password...
You will not be able to use the projector if you forget the password for some reason. If you forget the 
password, you will need to bring the following two items to your CASIO distributor to have the 
password cleared. Note that you will be charged to have the password cleared.
Note that your CASIO distributor will not be able to clear the password of your projector unless you 
bring both of the items listed above.
Also, keep the projector’s warranty in a safe place.
Important!Having your password cleared using the procedure described above will return all of the settings 
of your projector, except for the lamp time, to their initial factory defaults.
Password Protecting the Projector
[INPUT] [AUTO] [BLANK] [FREEZE] [] [] [] []
1. Personal identification (original or copy of your driver’s license, employee I.D., etc.)
2. Projector unit 
						

							22
Keep a written record of your password!
You will not be able to use the projector if you forget its password. We strongly suggest that you keep 
a written or other type of record of the password so you can look it up when necessary.
To change the password
1.Press the [MENU] key to display the setup menu.
2.Use the [] key to select “Option Settings 1”, and then press the [ENTER] key.
3.Use the [] key to select “Power On Password”, and then press the [ENTER] 
key.
This will display a dialog box prompting you to enter the current password.
4.Enter the current password.
If the projector is still protected by the factory default password, perform the key operation 
shown below to enter it.
5.After entering the current password, press the [ENTER] key.
This displays the Power On Password setting screen.
6.Use the [] key to select “Change Password”, and then press the [ENTER] key.
This will display a dialog box prompting you to enter the new password.
7.Enter a key sequence up to eight key operations long.
You can use any of the following keys as part of your password key sequence. 
[INPUT], [AUTO], [BLANK], [FREEZE], [VOLUME], [COLOR MODE], [D-ZOOM +], [D-ZOOM –], 
[KEYSTONE +], [KEYSTONE –], [MENU], [POINTER], [O], [f], [Z], [], [], [], [], [FUNC]
8.After entering the new password, press the [ENTER] key.
This will display a dialog box prompting you to enter the same password again.
9.Re-enter the same password key sequence you entered in step 7 and then press 
the [ENTER] key.
The message “Your new password has been registered.” indicates that the password has 
been changed. Press the [ESC] key.
If the password you entered in this step is different from the one you entered in step 7, the 
message “The password you input is wrong.” appears. Press the [ESC] key to return to step 7.[INPUT] [AUTO] [BLANK] [FREEZE] [] [] [] [] 
						

							23
To turn password protection on and off
1.Display the Power On Password setting screen by performing steps 1 through 5 
of the procedure under “To change the password” on page 22.
At this time, make sure that “Power On Password” is selected on the Power On Password 
setting screen.
2.Use the [] and [] keys to select “On” or “Off”.
Changing the power on password setting from “Off” to “On” causes the confirmation dialog 
box shown below to appear.
Press the [ENTER] key to confirm that you want to turn on power on password protection, or 
[ESC] to exit the dialog box without doing anything.
3.After you are finished, press the [MENU] key to exit the setup menu.
Entering the Password when Turning On the Projector
When you turn on the projector while password protection is turned on will cause a password input 
dialog box to appear on the projection screen. All projector operations will be accessible to you after 
you input the correct password and press the [ENTER] key.
NoteYou can perform the projection size adjustment operation ([ZOOM +] / [ZOOM …] keys), focus 
operation ([FOCUS] / [FOCUS] keys), and power off operation ([P] (Power) key) while the 
password input dialog box is on the projection screen. 
						

							24
You can use the procedures in this section to restore all of the settings on a particular main menu or all 
of the settings on the setup menu to their initial factory defaults.
To restore all settings on a particular main menu to their initial factory 
defaults
1.Press the [MENU] key to display the setup menu.
2.Use the [] and [] keys to select the main menu whose settings you want to 
restore to their initial factory defaults.
You can select Image Adjustment 1, Image Adjustment 2, Volume Adjustment, Screen 
Settings, Input Settings, Option Settings 1, or Option Settings 2.
3.Press the [ENTER] key.
4.Use the [] key to select “Restore Menu Defaults”.
5.Press the [ENTER] key.
This will display a confirmation screen like the screen shown below.
6.Use the [] key to select “Yes”.
7.To restore the settings of the main menu to their initial defaults, press the 
[ENTER] key.
To exit the operation without doing anything, press [ESC] instead of [ENTER].
8.After you are finished, press the [MENU] key to exit the setup menu.
NoteThe language setting and the password are not returned to their initial factory defaults if you 
select Option Settings 1 in step 2.
For details about how the above procedure initializes settings, see the explanations of the 
settings under “Setup Menu Contents” on page 26.
Restoring Projector Settings to Their Initial Factory 
Defaults 
						

							25
To restore all settings on the setup menu to their initial factory defaults
1.Press the [MENU] key to display the setup menu.
2.Use the [] key to select “Restore All Defaults” and then press the [ENTER] key.
3.After confirming that “Restore All Defaults” sub-menu is selected, press the 
[ENTER] key.
This displays a confirmation message asking if you want to initialize all settings.
4.Use the [] key to select “Yes”.
5.To restore all settings on the setup menu to their initial defaults, press the 
[ENTER] key.
This will restore all of the settings to their initial factory defaults, except for the Language, 
Lamp Time, Unit Operating Time and password settings.
To exit the operation without doing anything, press [ESC] instead of [ENTER].
6.After you are finished, press the [MENU] key to exit the setup menu. 
						

							26
This section contains tables that provide detailed explanations of all of the items included on the setup 
menu. The following describes the type of information that appears in each of the columns of the 
tables.
Image Adjustment 1 Main Menu
Setup Menu Contents
Setting Name: This column shows the names of the settings as they appear on the sub-menu.
Input: This column shows the input source for which each setting is supported.
Input source names are abbreviated as follows:
R : RGB input
C  : component video input
V  : video input
H : HDMI (PC) input
D  : HDMI (DTV) input
W : Wireless LAN input (USB port models only)
U  : USB input (USB port models only)
The letter N indicates that the setting can be configured while there is no input signal.
Setting Unit: The setting unit indicates how a setting is stored.
“Source Specific” in this column indicates that separate settings can be stored for each 
individual input source. For example, you could store an “Image Adjustment 1 
Brightness” setting of –1 for RGB input and a setting of +1 for VIDEO input.
“Single” in this column indicates that a single setting is stored and applied, regardless of 
the input source.
Description: This column provides details about the setting item and how to select it. The initial 
default setting is indicated by an asterisk (*).
Setting NameInputSetting UnitDescription
Brightness
RCVHDWUSource 
SpecificUse this sub-menu to adjust the brightness of the projected 
image. A larger value produces a brighter image.
Contrast
RCVHDWUSource 
SpecificUse this sub-menu to adjust the contrast of the projected image. 
A larger value produces a stronger contrast.
Sharpness
VSource 
SpecificUse this sub-menu to adjust the sharpness of the outlines in the 
projected image. A larger value makes the image sharper, while a 
smaller value makes it softer.
Saturation
VSource 
SpecificUse this sub-menu to adjust the color saturation of the projected 
image. A larger value increases color saturation.
Tint
VSource 
SpecificUse this sub-menu to adjust the tint of the projected image. 
A larger value makes the overall image more bluish, while a smaller 
value makes the overall image more reddish. This setting is 
supported only when the signal is NTSC or NTSC4.43. 
						

							27
Color ModeRCVHDWUSource 
SpecificYou can select from among four different color mode settings to 
optimize the projected image in accordance with image contents 
and projection conditions.
Standard:
Use this setting when you want to highlight the colors of your 
presentation.
Graphics:
Use this setting when you want photographs and graphics to 
appear natural.
Theater:
Use this setting to bring out the dark portions of your images.
Blackboard:
Use this setting for easy viewing when projecting onto a 
blackboard.
Color Balance
RCVHDWUSource 
SpecificThis sub-menu lets you adjust the color balance of the projected 
image.
Preset:
You can select from among three preset color balance settings: 
Warm, Normal,* Cold.
Color:
You can adjust the intensity of red, green, and blue within the 
range of –50 to +50. The intensity of a color increases along 
with the setting value. Color settings can be adjusted 
individually only when “Normal” is selected as the “Preset” 
setting.
Eco Off Mode
RCVHDWUSingle When “Off” is selected for “Option Settings 1 Eco Mode”, you 
can select either of the following projection image modes.
Mode1:
Gives priority to brightness.
Mode2:
Suppresses brightness slightly and gives priority to color 
balance.
Restore Menu 
Defaults
RCVHDWUSource 
SpecificUse this sub-menu to return all of the sub-menu items on the 
Image Adjustment 1 main menu to their initial default
settings.
Restoring menu defaults when there is no input signal will 
restore defaults for the currently selected input source.
Setting NameInputSetting UnitDescription 
						

							28
Image Adjustment 2 Main Menu
About the “Signal Specific” Setting Unit
For the items that have “Signal Specific” in the “Setting Unit” column of the above table, the setting is 
saved for the specific type of signal (XGA/60Hz, SXGA/60Hz, etc.) that is being input when the setting 
is performed, and not for a specific input source.
Volume Adjustment Main Menu
Setting NameInputSetting UnitDescription
Vertical 
Position
RCVSignal 
SpecificUse this sub-menu to adjust the vertical position of the input 
source image within the projection area.
Horizontal 
Position
RCVSignal 
SpecificUse this sub-menu to adjust the horizontal position of the input 
source image within the projection area.
Frequency
RSignal 
SpecificWhen vertical bands appear in the projected image while RGB is 
selected as the input source, it means that the frequency setting is 
not correct. When this happens, use this setting to adjust the 
frequency manually.
Important!If, for some reason, your manual frequency settings cause 
the image input from the computer to disappear from the 
projection, you can press the [AUTO] key to perform an auto 
adjust operation, which should cause the image to appear.
Phase
RSignal 
SpecificWhen there is flickering in the projected image while RGB is 
selected as the input source, it means that the phase setting is not 
correct. When this happens, use this setting to adjust the phase 
manually.
Restore Menu 
Defaults
RCVSource 
SpecificUse this sub-menu to return all of the sub-menu items on the 
Image Adjustment 2 main menu to their initial default settings.
Restoring menu defaults will restore defaults for the current 
signal type (XGA/60Hz, SXGA/60Hz, etc.) only.
Setting NameInputSetting UnitDescription
Volume
RCVHDWUNSource 
SpecificUse this sub-menu to adjust the volume level of the projector’s 
speaker.
Changing this setting when there is no input signal changes the 
volume setting of the currently selected signal source.
Restore Menu 
Defaults
RCVHDWUNSource 
SpecificUse this sub-menu to return Volume to its initial default setting.
Restoring menu defaults when there is no input signal will 
restore defaults for the currently selected input source. 
						

							29
Screen Settings Main Menu
Setting NameInputSetting UnitDescription
Keystone 
Correction
RCVHDWUNSingle Use this sub-menu to correct vertical keystoning of the projected 
image.
Aspect Ratio
RCVHDSource 
SpecificUse this sub-menu to select an aspect ratio setting for the 
projected image.
Input Source: RGB or HDMI (PC)Normal*:
Projects at the projector’s maximum possible size while 
maintaining the input signal aspect ratio.
Full:
Projects at the projector’s maximum possible size by enlarging 
or reducing the input signal.
True (XJ-A230/XJ-A235/XJ-A240/XJ-A245 only):
Projects the input signal at its actual size (1 input source dot 
equal to one projector output pixel dot) in the center of the 
projector’s projection screen. If the input signal resolution 
exceeds the projector’s output resolution, the excess is cut off.
Input Source: VIDEO, Component or HDMI 
(DTV)
Normal*:
Projects at the projector’s maximum possible size while 
maintaining the input signal aspect ratio.
16:9 :
This setting specifies a 16:9 aspect ratio, which is the same as a 
movie screen, high-definition TV, etc. Using this setting when 
the input signal is a 16:9 image that has been squeezed to a 4:3 
image causes the image to be displayed with its normal 16:9 
aspect ratio.
Letter Box (XJ-A230/XJ-A235/XJ-A240/XJ-A245 only):
This will resize the image horizontally to 1280 dots and project 
800 vertical dots of the center of the image, maintaining the 
aspect ratio of the input signal.
NoteWhen the input source is a component or an HDMI (DTV) 
signal with an aspect ratio of 16:9, the aspect ratio is 
fixed at 16:9. The aspect ratio setting cannot be changed 
in this case.
When projecting while “True” is selected as the aspect 
ratio setting for an RGB signal with a resolution that is 
less than SVGA, the image is enlarged to SVGA and 
projected.
For details about projection screen display conditions for 
different aspect ratio settings, see “Aspect Ratio Setting 
and Projection Image” (page 44).
Important!Note that enlarging or reducing the size of an image for 
commercial purposes or public presentation may infringe on 
the legally protected copyright of the copyright holder of the 
original material. 
						

							30
Projection 
ModeRCVHDWUNSingle Use this sub-menu to specify whether projection will be from the 
front of the screen or the back of the screen.
Front*:
Select this option to project from the front of the screen.
Rear:
Select this option to project from the back of the screen. This 
setting flips the front projected image horizontally.
Ceiling Mount
RCVHDWUNSingle Use this sub-menu to configure the projector for use in an 
installation in which it is positioned upside down.
On:
Flips the projected image horizontally and vertically.
Off*:
Projects a normal image.
Startup Screen
RCVHDWUNSingle Use this sub-menu to specify whether or not a startup screen 
should be projected whenever the projector is turned on.
Logo:
Select this option to project the projector’s built-in logo screen 
at startup.
None*:
Select this option when you do not want to project a startup 
screen.
No Signal 
Screen
RCVHDWUNSingle Use this sub-menu to specify what should be projected when 
there is no input signal to the projector.
Blue*:
Select this option to project a blue screen.
Black:
Select this option to project a black screen.
Logo:
Select this option to project the projector’s built-in logo screen.
Blank Screen
RCVHDWUNSingle Use this sub-menu to specify what should be projected after the 
[BLANK] key is pressed.
Blue:
Select this option to project a blue screen.
Black*:
Select this option to project a black screen.
Logo:
Select this option to project the projector’s built-in logo screen.
Restore Menu 
Defaults
RCVHDWUNSource 
SpecificUse this sub-menu to return all of the sub-menu items on the 
Screen Settings main menu to their initial default settings.
Restoring menu defaults when there is no input signal will 
restore defaults for the currently selected input source.
Note that the “Keystone Correction”, “Projection Mode”, 
“Ceiling Mount”, “Startup Screen”, “No Signal Screen”, and 
“Blank Screen” settings are always returned to their initial 
defaults, regardless of the currently selected input source.
Setting NameInputSetting UnitDescription