Casio Exilim EX Z5 User Manual

APPENDIX
231
If you have problems installing the USB driver...
You may not be able to install the USB driver properly if you use the USB cable to connect the camera to a computer running
Windows 98SE/98 before installing the USB driver from the bundled CD-ROM, or if you have another type of driver installed.
This will make it impossible for the computer to recognize the digital camera when it is connected. If this happens, you will
need to re-install the camera’s USB driver. For information about how to...

APPENDIX
232
Display Messages
Battery is low.
Cannot correct
image!
Can not find the file.
Cannot register any
more files.
Card ERROR
The battery is dead.
Keystone correction cannot be performed for some
reason. The image will be stored as-is, without
correction (pages 98, 100).
The camera cannot find a image specified by the
slideshow “Images” setting. Specify another image
(page 141).
•You are attempting to save a BEST SHOT scene
when there are already 999 scenes in the
“SCENE” folder (page 93).
•You...

APPENDIX
233
One of the following problems occurred during
printing.
•Printer power off
•Printer internal error
Image compression could not be performed during
image data storage for some reason. Record the
image again.
The camera is in the Printer mode, and the printer
is running low on ink or is out of ink.
If the lens comes into contact with some obstacle,
this message appears and the camera turns off. Take
action to remove the obstacle, and try turning on
power again.
Your camera system is corrupted....

APPENDIX
234
CA-32 USB Cradle/AC Adaptor (Option)
You can perform the following operations after setting the
camera onto the optional CA-32 USB Cradle/AC Adaptor.
•Charging of the camera’s rechargeable lithium ion
battery.
•Viewing of images using the Photo Stand slideshow
feature.
•TV connectability for viewing of images on a television
screen.
•Direct connection to a printer for printing.
•Transfer of images recorded with the camera to a
computer over a USB connection.
General Guide
The following...

APPENDIX
235
Using the USB Cradle to Charge the
Battery
You can charge the camera’s NP-20 rechargeable lithium
ion battery by setting the camera onto the USB cradle.
1.Load the rechargeable litium ion battery (NP-
20) into the camera.
2.Connect the bundled AC adaptor to the [DC IN
5.3V] connector of the USB cradle, and then
plug it in to a household power outlet.
AC Adaptor
[DC IN 5.3V]
USB Cradle
AC power cord
 NOTE 
•The bundled AC adaptor is designed for operation
with any power supply in the range of...

APPENDIX
236
4.With the camera
positioned with the
monitor screen facing
forward as shown in
the illustration, place it
onto the USB cradle.
•Do not place the camera
onto the USB cradle
while it is turned on.
•The [CHARGE] lamp on
the USB cradle should
turn red, indicating that charging has started. When
charging is complete, the [CHARGE] lamp will turn
green.
•It takes about 130 minutes to achieve a full charge.
Actual charging time depends on current battery
capacity and charging conditions.
5.After...

APPENDIX
237

 If the camera does not work normally
This can mean there is a problem with how the battery is
loaded. Perform the following steps.
1.Remove the battery from the camera and
check the battery contacts for dirt. If the
contacts are dirty, wipe them clean with a dry
cloth.
2.Check to make sure that the AC adaptor’s
power cord is connected securely to the
power outlet and USB cradle.
•If the same symptoms occur again when you place
the camera on the USB cradle after taking the above
steps,...

APPENDIX
238
Using the Photo Stand Feature
The “Photo Stand” feature lets you specify what should
appear on the camera’s monitor screen while the camera is
on its USB cradle. You can play a Photo Stand slideshow
without worrying about remaining battery power, or you can
specify display of a particular image. Photo Stand feature
operations are performed in accordance with slideshow
setting. Before using Photo Stand feature, you need to
configure slideshow settings as described in the camera
user’s guide....

APPENDIX
239
Using the USB Cradle to Display Images
on a TV Screen
You can place the camera onto the USB cradle and
connect the cradle to a TV to view camera images on a TV
screen.
1.Connect one end of the AV cable that comes
with the camera to the [AV OUT] port of the
USB cradle, and the other end to the video
input terminal of the TV.
AV cable (bundled)
[AV OUT] (AV output port) Video input
terminal TV
•Connect the yellow plug of the AV cable to the video
input (yellow) terminal of the TV, and the...

APPENDIX
240
Using the USB Cradle to Print Images
You can place the camera onto the USB cradle and
connect the cradle to a printer to print images.
1.Connect the USB cable that comes bundled
with the camera to the USB cradle and a
printer.
USB portConnector A
USB cable
(bundled)Connector B
[] (USB port)
•Also, connect the AC adaptor to the USB cradle and
plug the AC adaptor into an electrical outlet.
•If you are using battery power without the AC
adaptor, make sure that the battery is fully charged....