Casio Exilim EX Z5 User Manual

PRINTING IMAGES
181
To configure print settings for all images
1.In the PLAY mode, press [MENU].
2.Select the “PLAY” tab, select “DPOF”, and
then press [].
3.Use [
] and [] to select “All images”, and
then press [].
4.Use [
] and [] to
specify the number of
copies.
•You can specify up to 99
for the number of copies.
Specify 00 if you do not
want to have the image
printed.
5.To turn on date stamping for the prints, press
[BS] so “On” is displayed.
•“On” indicates that date stamping is turned on....

PRINTING IMAGES
182
 IMPORTANT! 
•DPOF settings are not cleared automatically after
printing is complete. This means that if you perform
another printing operation without clearing DPOF
settings, printing will be performed in accordance
with the last settings you configured. If you want to
prevent this from happening, perform the procedure
under “To configure print settings for all images”
(page 181) and change the number of copies to “00”.
After that, you can configure new DPOF settings as
required.
•If...

PRINTING IMAGES
183
Using PictBridge or USB DIRECT-PRINT
You can connect the camera
directly to a printer that supports
PictBridge or USB DIRECT-PRINT,
and perform image selection and
printing using the camera monitor
screen and controls. DPOF support
(page 179) also lets you specify
which images you want to print and
how many copies of each should be
printed.
•PictBridge is a standard
established by the Camera and
Imaging Products Association
(CIPA).
•USB DIRECT-PRINT is a
standard proposed by Seiko...

PRINTING IMAGES
184

 Connecting the Camera to Your Printer
1.Check the battery level indicator to make sure
that the battery is fully charged, and then
press the power button to turn off the camera.
•If battery power is low, replace the battery.
•The camera does not draw power over the USB
cable.
USBUSB portUSB cable (bundled)
USB/AV connector
2.Use the USB cable that comes with the
camera to connect the camera to a printer.
•Take care when connecting the USB cable to the
camera or your printer. USB...

PRINTING IMAGES
185
4.Use [
] and [] to select “Paper Size”, and
then press [].
5.Use [
] and [] to select the paper size you
want to use for printing, and then press [SET].
•The following are the print sizes that are available.
3.5˝ ×
 5˝
5˝ ×
 7˝
4˝ ×
 6˝
A4
8.5˝ ×
 11˝
By Printer
•Selecting “By Printer” prints using the paper size
selected on the printer.
•Available paper size settings depend on the
connected printer. For full details, see the
instructions that come with your printer.

 Printing...

PRINTING IMAGES
186
7.On the camera’s monitor screen, use [
] and
[] to select “Print”, and then press [SET].
•This starts printing and displays the message
“Busy.... Please wait...” on the monitor screen. The
message will disappear after a short while, even
though printing is still being performed. Pressing any
of the camera’s buttons while printing is in progress
will cause the message to reappear.
•The print menu will appear when printing is
complete.
•If you selected “1 Image” in step 6, you can...

PRINTING IMAGES
187
Date Printing
Any one of the procedures described below can be used to
include the recording date in image prints. Correct date
printing requires that the current date be set on the camera
before the image is recorded.
•Before recording the image, turn on date stamping
(“Date” or “Date&Time”) (page 122).
•Specifying date printing with DPOF settings (page 180)
—If you use the DPOF setting to turn on date stamping
for printing on an image that already has date/time
stamp data embedded...

PRINTING IMAGES
188
Exif Print
Exif Print is an
internationally supported,
open standard file format
that makes it possible to
capture and display vibrant
digital images with accurate
colors. With Exif 2.2, files
include a wide range of
shooting condition
information that can be
interpreted by an Exif Print
printer to produce better-
looking prints.
 IMPORTANT! 
•Information about the availability of Exif Print
compatible printer models can be obtained from each
printer manufacturer.
PRINT Image Matching...

VIEWING IMAGES ON A COMPUTER
189
VIEWING IMAGES ON A COMPUTER
After establishing a USB connection between the camera
and your computer, you can use your computer to view
images in file memory and copy images to your computer’s
hard disk or other storage media. In order to do this, you
first need to install the USB driver located on the CD-ROM
that comes bundled with the camera onto your computer.
Note that the procedure you need to perform depends on
whether you are using computer running under Windows...

VIEWING IMAGES ON A COMPUTER
190
 IMPORTANT! 
• If battery goes low during printing, printing may stop
and the camera may shut down.
• If you plan to transfer file data from the camera’s
built-in memory to your computer, make sure there is
no memory card loaded in the camera. If there is,
remove the memory card from the camera before
you connect to your computer.

 Install the USB driver onto your computer
Do not try to establish a connection between the
camera and computer before installing the USB...