Casio Exilim EX V8 User Manual

							201MANAGING YOUR FILES Perform the following steps to view FAVORITE folder 
contents on your computer.
1.Remove the memory card from the camera.
2.Place the camera on the USB cradle (which is 
connected to the computer).
3.Perform the required operations on your 
computer to navigate to the camera’s memory 
and display the FAVORITE folder contents.
Files can be copied from the camera’s built-in memory to a 
memory card, or from a memory card to built-in memory.
This makes it possible, for example, to perform the following 
steps and copy a file from your memory card to another person’s 
memory card.
1Copy the file from your memory card to the camera’s built-in 
memory.
2Remove your memory card and insert the other person’s 
memory card.
3Copy the file from built-in memory to the other memory card.
IMPORTANT!
•You can copy snapshots, movies, audio snapshots, or 
Voice Recording files you recorded with your camera.
•You cannot copy a snapshot that is in the FAVORITE 
folder.
•When a copied file image appears on the full-month 
calendar screen, it is displayed on the date that it was 
copied (page 172).
Copying Files
Downloaded From camera-usermanual.com Casio Manuals 
						

							202MANAGING YOUR FILES
■Copying All Files in Built-in Memory to a 
Memory Card
The following operation copies all files from built-in memory to a 
memory card. You cannot copy files individually.
1.Load the memory card to which you want to 
copy the files into the camera.
2.Turn on the camera, enter the PLAY mode and 
then press [MENU].
3.On the “PLAY” tab, select “Copy” and then 
press [X].
4.Use [S] and [T] to select “Built-in   Card” 
and then press [SET].
This starts the copy operation. Wait until the “Busy... Please 
wait...” message disappears from the monitor screen before 
performing any operation on the camera.
•After the copy operation is complete, the last file copied 
will be displayed on the monitor screen.
■Copying a Single File from a Memory Card to 
Built-in Memory
With this procedure, files must be copied one-by-one.
1.Load the memory card that contains the file 
you want to copy into the camera.
2.Turn on the camera, enter the PLAY mode and 
then press [MENU].
3.On the “PLAY” tab, select “Copy” and then 
press [X].
4.Use [S] and [T] to select “Card   Built-in” 
and then press [SET].
5.Use [W] and [X] to select the file you want to 
copy.
6.Use [S] and [T] to select “Copy” and then 
press [SET].
This starts the copy operation. Wait until the “Busy... Please 
wait...” message disappears from the monitor screen before 
performing any operation on the camera.
•The copied image reappears on the monitor screen after 
the copy operation is complete.
Downloaded From camera-usermanual.com Casio Manuals 
						

							203MANAGING YOUR FILES
7.Now you can repeat steps 5 and 6 to copy 
another file, or you can exit this procedure by 
pressing [MENU].
NOTE•Files are copied to the folder in built-in memory whose 
name has the largest serial number.
Downloaded From camera-usermanual.com Casio Manuals 
						

							204DELETING FILES
DELETING FILES
You can delete files you no longer need, or after you transfer 
them to your computer’s hard disk or print them. This frees up 
memory for new files.
You can delete one specific file, or you can delete all files 
currently in memory.
Here we will explain the different file delete procedures, 
including how to delete snapshots from the FAVORITE folders.
IMPORTANT!
•Remember that a file delete operation cannot be undone. 
Always make sure that you really no longer need a file 
before deleting it.
•A protected file cannot be deleted. To delete a protected 
file, first remove its protection (page 197).
•Deleting an audio snapshot deletes both the snapshot and 
the audio file.
1.In the PLAY mode, 
press [T] ( ).
2.Use [W] and [X] to scroll through the images 
until the one for the file you want to delete is 
on the monitor screen.
3.Use [S] and [T] to select “Delete” and then 
press [SET].
•To exit the delete operation without deleting anything, 
select “Cancel”.
4.Now you can repeat steps 2 and 3 to delete 
another file.
•You can exit this procedure by pressing [MENU].
Deleting a Specific File
Downloaded From camera-usermanual.com Casio Manuals 
						

							205DELETING FILES
1.In the PLAY mode, press [T] ( ).
2.Use [S] and [T] to select “All Files Delete” 
and then press [SET].
3.In response to the confirmation message that 
appears, use [S] and [T] to select “Yes”.
•To cancel the delete operation, select “No” instead of 
“Yes”.
4.Press [SET].
•This deletes all of the files and displays the message 
“There are no files.”You can delete a single snapshot, or you can delete all the 
snapshots currently in the FAVORITE folder.
1.In the PLAY mode, press [MENU].
2.On the “PLAY” tab, select “Favorites” and 
then press [X].
3.Use [S] and [T] to select “Show” and then 
press [SET].
4.Press [T] ( ).
5.Use the procedures under “Deleting a Specific 
File” and “Deleting All Files” to delete the 
snapshots you want.
•You can exit this procedure by pressing [MENU] twice.
Deleting All FilesDeleting FAVORITE Folder Snapshots
Downloaded From camera-usermanual.com Casio Manuals 
						

							206OTHER SETTINGS
OTHER SETTINGS
Your camera lets you configure the following sound settings.
•Type of sound and volume for shutter release and other 
operations
•Volume level for movie and Voice Recording playback
■Selecting the Operation Sound
1.Press [MENU].
2.On the “Set Up” tab, select “Sounds” and then 
press [X].
3.Use [S] and [T] to select the operation whose 
sound you want to configure (Startup, Half 
Shutter, Shutter, Operation) and then press 
[X].
4.Use [S] and [T] to select the setting you want 
and then press [SET].Configuring Camera Sound Settings
To do this:Select this setting:
Sound one of the built-in 
sounds (1 through 5)Sound 1 - 5
Turn sound off Off
Downloaded From camera-usermanual.com Casio Manuals 
						

							207OTHER SETTINGS
■Setting the Operation Tone Volume Level
1.Press [MENU].
2.On the “Set Up” tab, select “Sounds” and then 
press [X].
3.Use [S] and [T] to select “  Operation”.
4.Use [W] and [X] to specify the playback 
volume setting you want and then press [SET].
•You can set the volume to one of eight levels in the range 
of 0 (lowest) to 7 (highest).
•Setting a volume level of 0 mutes the sound.
NOTE•The volume setting you configure here is also applied to 
video output (page 166).
■Setting the Playback Volume Level
You can use this procedure to set the playback volume level for 
movies and audio snapshots, independent of the operation tone 
volume.
1.Press [MENU].
2.On the “Set Up” tab, select “Sounds” and then 
press [X].
3.Use [S] and [T] to select “  Play”.
4.Use [W] and [X] to specify the operation tone 
volume setting you want and then press [SET].
•You can set the volume to one of eight levels in the range 
of 0 (lowest) to 7 (highest).
•Setting a volume level of 0 mutes the sound.
IMPORTANT!
•The volume setting you configure here does not affect the 
video output (page 166).
Downloaded From camera-usermanual.com Casio Manuals 
						

							208OTHER SETTINGS
You can configure the camera to display a startup screen of an 
image you recorded, whenever you turn it on.
•Even if you configure startup screen settings in the PLAY 
mode, the startup screen does not appear when turn on the 
camera by pressing [ ] (PLAY).
1.Press [MENU].
2.On the “Set Up” tab, select “Startup” and then 
press [X].
3.Use [W] and [X] to scroll through the images 
until the one you want to use as the startup 
screen is on the monitor screen.
4.Use [S] and [T] to select the setting you want 
and then press [SET].
NOTE•The following are the types of images that you can select 
for the startup screen.
– Special startup screen images built into the camera
– Snapshots
– Audio snapshots (Audio does not play.)
•Only one startup screen image can be in effect at any time. 
To change the startup screen to another image, simply 
overwrite the current image with the new one.
•Formatting built-in memory (page 218) will delete the 
current startup screen image.
Turning the Startup Screen On or Off
To do this:Select this setting:
Use the selected image as the 
startup screenOn
Turn off the startup screen Off
Downloaded From camera-usermanual.com Casio Manuals 
						

							209OTHER SETTINGS
Use the following procedure to specify the rule that governs 
generation of the serial number used in file names (page 196).
1.Press [MENU].
2.On the “Set Up” tab, select “File No.” and then 
press [X].
3.Use [S] and [T] to select the setting you want 
and then press [SET].
Specifying the File Name Serial 
Number Generation RuleTo have the camera do this:Select this 
setting:
Remember the numbers used for files. Files will 
be named using the next sequential number, 
even if files are deleted or if a blank memory card 
is loaded.
•If a memory card is loaded that already has 
files stored on it and the largest sequential 
number in the existing file names is greater 
than the largest sequential number 
remembered by the camera, numbering of new 
files will start from the largest sequential 
number in the existing file names plus 1.Continue
Restart the serial number from 0001 whenever all 
files are deleted or when the memory card is 
replaced with a blank one.
•If a memory card is loaded that already has 
files stored on it, numbering of new files will 
start from the largest sequential number in the 
existing file names number plus 1.Reset
Downloaded From camera-usermanual.com Casio Manuals 
						

							210OTHER SETTINGS
When changing the date and time setting, be sure to do so for 
your Home City (the location where you normally use the 
camera). If you already have your Home City setting configured 
correctly, you can use the procedure under “Setting the Date 
and Time for Your Home City” (page 211) to change the current 
time setting only, if you want.
IMPORTANT!
•Changing the time and date setting without correctly 
configuring your Home City setting first will cause all of the 
World Time (page 212) dates and times to be off.
■Selecting Your Home City
1.Press [MENU].
2.On the “Set Up” tab, select “World Time” and 
then press [X].
This displays the current World Time settings.
3.Use [S] and [T] to select “Home” and then 
press [X].
4.Use [S] and [T] to select “City” and then 
press [X].
5.Use [S], [T], [W], and [X] to select the area 
where your Home City is located and then 
press [SET].
6.Use [S] and [T] to select your home city and 
then press [SET].
7.After the setting is the way you want, press 
[SET] to exit the setting screen.
Changing the Camera Date and Time 
Setting
Downloaded From camera-usermanual.com Casio Manuals